Related Manuals for Master Chef 85-1603-8
Summary of Contents for Master Chef 85-1603-8
- Page 1 This Owner's Manual is provided and hosted by Appliance Factory Parts. Master Chef G10601 Owner's Manual Shop genuine replacement parts for Master Chef G10601 Find Your Master Chef Grill Parts - Select From 118 Models -------- Manual continues below --------...
- Page 2 Outdoor Stovetop S A F E U S E , C A R E A N D A S S E M B L Y M A N U A L D A N G E R If you smell Gas 1.
- Page 3 W A R R A N T Y 1 Year Limited Warranty This Masterchef Outdoor Stovetop carries a 1 year limited warranty against defects in manufacturing workmanship. This Limited Warranty is nontransferable and becomes void if used for commercial or rental purposes. This warranty applies only when unit is used in Canada.
- Page 4 I N F O R M A T I O N The installation of this appliance must be in accordance with all local codes, or in the absence of local codes: I N S T A L L A T I O N Canadian installation must conform to the current national standards, which at •...
- Page 5 The Cylinder must also be equipped with: A shut-off valve with a correct cylinder valve outlet as specified in current standards. • Canada: CAN/ CGA 1.6g-M97 Outdoor Gas Grills. • U.S.A: ANSI Z21.58a-2006/CSA 1.6a-2006 Outdoor Cooking Appliances. • a) Constructed and marked in accordance with the Specifications for LP-Gas Cylinders of the U.S.
- Page 6 F I L L I N G T H E For safety reasons the LP gas cylinder, if supplied with your barbecue, has been shipped empty. The cylinder must be filled prior to use and must have the air L . P . C Y L I N D E R purged.
- Page 7 Attention: Improperly lighting the barbecue can activate the flow control feature, resulting in lower heat output. If this occurs, the re-flow feature must be reset by turning off all the burner controls and the cylinder valve. Wait at least 30 seconds before slowly turning on the cylinder valve, and then after another 5 seconds turn the burner valve on and light the barbecue.
- Page 8 P R I O R T O U S I N G Do not use your barbecue until you have carefully read and fully understand all the information in this manual. Please ensure the following: Your barbecue is properly assembled. •...
- Page 9 L I G H T I N G Prior to lighting your Outdoor Stovetop, visually check all hoses before each use, for nicks, cracking, abrasions or cuts. If the hose is found to be damaged in any T H E B A R B E C U E way, do not use your barbeque.
- Page 10 Match-Lighting Do not lean over burner while lighting. 1. Remove lid. Turn on gas at LP cylinder. 2. Place lit match into match holder. Place match near burner. 3. Push in and turn burner knob to HI. Be sure burner lights and stays lit. W A R N I N G Use this slot for manual match lighting If the heat output is too low, the flow control feature may have...
- Page 11 S A F E T Y C H E C K Burner Check Light burner, rotate knob from HI to LOW. You should see a smaller flame in the LOW position than the HI position. Always check flame prior to each use. Burner Flame Check Inspect burner prior to each use.
-
Page 12: Troubleshooting Guide
T R O U B L E S H O O T I N G G U I D E Problem Possible Causes Corrective Action Burner will not light Blocked venturi tubes Clean out blockage • • (match or igniter) Cylinder or gas supply valve turned off Open cylinder or gas supply valve •... - Page 13 P A R T S L I S T Item No. Quantity Description Part No. Top Lid G106-0008-01 8 5 - 1 6 0 3 - 8 ( G 1 0 6 0 1 ) Handle, Top Lid G402-0001-02 Top Support Frame G106-0200-01 Cooking grate G106-0007-01...
- Page 14 Manual Hardware Pack...
- Page 15 A S S E M B L Y I N S T R U C T I O N S Hardware Pack List Key No. Description Part Number Quantity Tools needed for assembly are shown below. No.10-24 UNC x 25 Screw 20124-10025-03A ø5 Washer 40300-05000-250...
- Page 16 Insert 3 vertical supporting bars (CH) into tank support (DA). Secure the supporting bars to the tank support using hardware #1 (x6) and #2 (x6). Assemble the side panel (CF), front panel (CE) and support- ing bars (CH) together as shown using hardware #3 (x16). Assemble the igniter (CB) to the control panel (CA) as shown.
- Page 17 Position the control panel (CA) into the hole located on the front panel (CE) using hardware #3 (x4). Place the control knob (CC) on as shown. Assemble the cart handle (CJ) to the side panel (CF) using hardware #6 (x2) as shown. Assemble the Bracket Holder (CK) to the bottom of Heat Shield (BE) using hardware #11 (x2) as shown.
-
Page 18: Very Important
7.1 Assemble the burner assembly (BC) to the heat shield by positioning the burner Venturi tube through the hole located in the heat shield, using hardware #7 (x3). 7.2 Assemble the heat shield and burner to the top of the cart body using hardware #3 (x4). - Page 19 Assemble the back panel (CG) by attaching to the heat shield as shown. Then place lid to cover the top of this unit. C A U T I O N Lid should only be used for storing after Side burner unit has cooled down. Never place cover over burner when unit is in operation.
- Page 20 Remove one of the hardware #3 (self tapping screw) from the Front Panel (CE), then connect the Retention Hook to the Front panel (CE) as shown using the same hardware which was just removed (hardware #3) and a 5mm washer (hardware #2). Important! Clip the regular PVC hose to the hook as shown before connecting the QCC1 regulator to the gas tank.
- Page 21 D I S T R I B U T O R Trileaf Distribution Trifeuil Toronto, Canada M4S 2B8...
Need help?
Do you have a question about the 85-1603-8 and is the answer not in the manual?
Questions and answers