A l l t r a d e m a r k s , b r a n d n a m e s , a n d b r a n d s a p p e a r i n g h e r e i n a r e t h e p r o p e r t y o f t h e i r r e s p e c t i v e o w n e r s .
• C r i t i c a l a n d e x p e d i t e d s e r v i c e s
• I n s t o c k / R e a d y - t o - s h i p
Artisan Scientific Corporation dba Artisan Technology Group is not an affiliate, representative, or authorized distributor for any manufacturer listed herein.
In Stock
Used and in Excellent Condition
Buy Today!
https://www.artisantg.com/94400-6
• We b u y y o u r e x c e s s , u n d e r u t i l i z e d , a n d i d l e e q u i p me n t
• F u l l - s e r v i c e , i n d e p e n d e n t r e p a i r c e n t e r
±10 v, 20 ms/s/ch, 14-bit, 4-channel c series digitizer module (10 pages)
Summary of Contents for National Instruments 9213
Page 1
NI NI 9213 16 TC, High-Density Thermocouple Module (Spring Terminal) In Stock Used and in Excellent Condition Buy Today! https://www.artisantg.com/94400-6 A l l t r a d e m a r k s , b r a n d n a m e s , a n d b r a n d s a p p e a r i n g h e r e i n a r e t h e p r o p e r t y o f t h e i r r e s p e c t i v e o w n e r s .
Page 2
GETTING STARTED GUIDE NI 9213 16 TC, ±78 mV, 24 Bit, 75 S/s Aggregate hnology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www...
This document explains how to connect to the NI 9213. Before you begin, complete the software and Note hardware installation procedures in your chassis documentation. The guidelines in this document are specific to Note the NI 9213. The other components in the system might not meet the same safety ratings.
Do not connect the NI 9213 to signals or use Caution for measurements within Measurement Categories III or IV. Safety Guidelines for Hazardous Voltages If hazardous voltages are connected to the device, take the following precautions. A hazardous voltage is a voltage greater than 42.4 Vpk voltage or 60 VDC to earth ground.
Safety Guidelines for Hazardous Locations The NI 9213 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4 and Ex nA IIC T4 hazardous locations; and nonhazardous locations only.
Page 7
Zone 2 hazardous locations, in ambient temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI 9213 in Gas Group IIC hazardous locations, you must use the device in an NI chassis that has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.
In addition, take precautions when designing, selecting, and installing measurement probes and cables to ensure that the desired EMC performance is attained. 8 | ni.com | NI 9213 Getting Started Guide hnology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www...
Preparing the Environment Ensure that the environment in which you are using the NI 9213 meets the following specifications. Operating temperature -40 °C to 70 °C (IEC 60068-2-1, IEC 60068-2-2) Operating humidity 10% RH to 90% RH, (IEC 60068-2-78) noncondensing...
Page 13
Figure 1. Connecting a Thermocouple to the NI 9213 Shield Thermocouple TC– NI 9213 reference Connect the shield to a common-mode voltage reference on the thermocouple. A valid common-mode voltage reference is a voltage that is within ±1.2 V of the common-mode voltage of the thermocouple 12 | ni.com | NI 9213 Getting Started Guide...
Page 15
2. Press a wire into the open connector terminal. 3. Remove the screwdriver from the activation slot to clamp the wire into place. 14 | ni.com | NI 9213 Getting Started Guide hnology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www...
• Make sure the NI 9213 terminals are facing forward or upward. • Keep the NI 9213 in a stable and consistent orientation. • Allow the thermal gradients to settle after a change in system power or in ambient temperature. A change in system power can happen when the system powers on, the system comes out of sleep mode, or you insert/remove modules.
You can obtain the DoC for your product by visiting ni.com/certification. If your product supports calibration, you can obtain the calibration certificate for your product at ni.com/calibration. 18 | ni.com | NI 9213 Getting Started Guide hnology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www...
Need help?
Do you have a question about the 9213 and is the answer not in the manual?
Questions and answers