Download Print this page
Sealey SA55 Instructions
Sealey SA55 Instructions

Sealey SA55 Instructions

Air scissors

Advertisement

Quick Links

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
 WARNING! Ensure Health & Safety, local authority and general workshop practice regulations
are adhered to when using this equipment.
 WARNING! Disconnect from air supply before changing accessories or servicing.
 Maintain the tool in good condition and replace any damaged or worn parts. Use
genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
 Wear approved safety eye/face shield, ear defenders and hand protection.
 Keep fingers clear of blades.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Keep children and non essential persons away from the working area.
 DO NOT use the tool for a task it is not designed to perform.
 WARNING! DO NOT use tool if damaged or thought to be faulty. Contact Sealey service agent.
 DO NOT use tool unless you have been instructed in its use by a qualified person.
 DO NOT carry the tool by the air hose, or yank the hose from the air supply.
 DO NOT operate tool if you are tired or under the influence of alcohol, drugs or intoxicating
medication.
 DO NOT carry tool with your hand on the power trigger in order to avoid unintentional starting.
 DO NOT direct air from the air hose at yourself or others.
 When not in use disconnect from air supply and store in a safe, dry, childproof location.
 WARNING: The warnings, cautions and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood
that common sense and caution are factors which cannot be built into this product, but must
be applied by the operator.
2.
INTRODUCTION & SPECIFICATION
Polished aluminium housing with textured grip handle. Suitable for accurately cutting metal sheet.
Unlike air shears this tool is ideal for trimming ragged sheet edges to gain a flat finish.
Handle exhaust helps reduce noise level.
Max. Cutting Capacity: . . .1.2mm(Steel Sheet)
Air Consumption: . . . . . . . . . . . . . . . . . 4.3cfm
Operating Pressure: . . . . . . . . . . . . . . . . 90psi
Air Inlet Size: . . . . . . . . . . . . . . . . . . . 1/4"BSP
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4kg
Replacement Blade Left: . . . . . . . . . . SA55.36
Replacement Blade Right: . . . . . . . . . SA55.37
Noise Power: . . . . . . . . . . . . . . . . . . . . 78dB.A
Noise Pressure: . . . . . . . . . . . . . . . . . . 94dB.A
Original Language Version
INSTRUCTIONS FOR:
AIR SCISSORS
SA55
MODEL No:
SA55
Issue: 2 - 06/11/09

Advertisement

loading
Need help?

Need help?

Do you have a question about the SA55 and is the answer not in the manual?

Questions and answers

Summary of Contents for Sealey SA55

  • Page 1 SA55 MODEL No: Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
  • Page 2 To replace the blades (36 and 37), loosen the three lock screws (34) and slide the cutter housing (33) off the gear case (29). Remove the two lock screws (34) that secure the blades (36, 37 and 39) and remove the blades. Original Language Version SA55 Issue: 2 - 06/11/09...
  • Page 3 Slide the cutter housing onto the gear casing and secure using the lock screw. Tighten all three lock screws. 5.2. If the system does not have an oiler lubricate the tool daily with a few drops of Sealey air tool oil dripped into the air inlet. 5.3.