Murata GCD219R72A332KA01 Series Reference Sheet

Chip monolithic ceramic capacitor mlsc serial for automotive

Hide thumbs

page of 28

/ 28
Bookmarks

Quick Links

Download this manual

Chip Monolithic Ceramic Capacitor MLSC Serial for Automotive

GCD219R72A332KA01_ (0805, X7R:EIA, 3300pF, DC100V)

_: packaging code

1.Scope

This product specification is applied to Chip Monolithic Ceramic Capacitor MLSC Serial used for Automotive Electronic equipment.

2.MURATA Part NO. System

(Ex.)

GCD

(1)L/W

Dimensions

3. Type & Dimensions

(1)-1 L

(1)-2 W

2.0±0.15

1.25±0.15

4.Rated value

(3) Temperature Characteristics

(Public STD Code):X7R(EIA)

Temp. coeff

or　Cap. Change

-15 to 15 %

5.Package

mark

(8) Packaging

f180mm Reel

PAPER W8P4

f330mm Reel

PAPER W8P4

Product specifications in this catalog are as of Jun.6,2016,and are subject to change or obsolescence without notice.

Please consult the approval sheet before ordering.

Please read rating and !Cautions first.

GCD219R72A332KA01-01

(2)T

(3)Temperature

Dimensions

Characteristics

(2) T

0.85±0.1

0.2 to 0.7

(4)

Rated

Temp. Range

Voltage

(Ref.Temp.)

-55 to 125 °C

DC 100 V

(25 °C)

Packaging Unit

4000 pcs./Reel

10000 pcs./Reel

332

(4)Rated

(6)Capacitance

(5)Nominal

Voltage

Capacitance

(Unit:mm)

0.7 min.

Specifications and Test

(6)

(5) Nominal

Capacitance

Tolerance

3300 pF

±10 %

Reference Sheet

A01

(7)Murata's Control

(8)Packaging Code

Tolerance

Code

Methods

(Operating

Temp. Range)

-55 to 125 °C

Need help?

Do you have a question about the GCD219R72A332KA01 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Murata GCD219R72A332KA01 Series

Page 1 GCD219R72A332KA01_ (0805, X7R:EIA, 3300pF, DC100V) _: packaging code Reference Sheet 1.Scope This product specification is applied to Chip Monolithic Ceramic Capacitor MLSC Serial used for Automotive Electronic equipment. 　　 2.MURATA Part NO. System (Ex.) (2)T (7)Murata’s Control (1)L/W (4)Rated (3)Temperature...
Page 2 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method Pre-and Post-Stress Electrical Test 2 High Temperature The measured and observed characteristics should satisfy Solder the capacitor on the test board (glass epoxy board). Exposure (Storage) the specifications in the following table.
Page 3 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method The measured and observed characteristics should satisfy the 7 Operational Life Solder the capacitor on the test board (glass epoxy board). specifications in the following table.
Page 4 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method 14 Thermal Shock The measured and observed characteristics should satisfy the Solder the capacitor on the test board (glass epoxy board). specifications in the following table.
Page 5 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method 18 Board Flex Appearance No marking defects Solder the capacitor on the test board (glass epoxy board) shown in Fig1. Then apply a force in the direction shown in Fig 2 for 60s.
Page 6 ■AEC-Q200 Murata Standard Specification and Test Methods AEC-Q200 Test Item Specification. AEC-Q200 Test Method 21 Capacitance Capacitance R7 : Within ±15% The capacitance change should be measured after 5min. at each specified temperature stage. Temperature Change (-55℃ to +125℃) Characteristics The ranges of capacitance change compared with the above 25℃...
Page 7 Package GCD Type 1.Tape Carrier Packaging(Packaging Code:D/E/F/L/J/K) 1.1 Minimum Quantity(pcs./reel) φ180mm reel φ330mm reel Type Paper Tape Plastic Tape Paper Tape Plastic Tape Code:D/E Code:L Code:J/ F Code:K GCD18 4000 10000 4000 10000 GCD21 4000 10000 3000 10000 1.2 Dimensions of Tape 　(1)GCD18/21 <Paper Tape>...
Page 8 態 ( 単位： mm) Package GCD Type Fig.1 Package Chips (in mm) Chip Fig.2 Dimensions of Reel 2.0±0.5 φ21±0.8 ｗ Fig.3 Taping Diagram 16.5 max. 10±1.5 Top Tape : Thickness 0.06 Feeding Hole :As specified in 1.2. Hole for Chip : As specified in 1.2. Bottom Tape :Thickness 0.05 (Only a bottom tape existence ) Base Tape : As specified in 1.2.
Page 9 Package GCD Type ﾌﾟ詰め状態 ( 単位： mm) 1.3 Tapes for capacitors are wound clockwise shown in Fig.3. (The sprocket holes are to the right as the tape is pulled toward the user.) 1.4 Part of the leader and part of the vacant section are attached as follows. Tail vacant Section Chip-mounting Unit Leader vacant Section...
Page 10 Caution ■Limitation of Applications Please contact us before using our products for the applications listed below which require especially high reliability 　 for the prevention of defects which might directly cause damage to the third party's life, body or property. 　　　①Aircraft equipment ②Aerospace equipment ③Undersea equipment ④Power plant control equipment...
Page 11 Caution 2.Measurement of Capacitance 1. Measure capacitance with the voltage and frequency specified in the product specifications. 1-1. The output voltage of the measuring equipment may decrease occasionally when capacitance is high. Please confirm whether a prescribed measured voltage is impressed to the capacitor. 1-2.
Page 12 Caution 5. DC Voltage and AC Voltage Characteristic 1. The capacitance value of a high dielectric constant type [Example of DC Voltage Characteristics] capacitor changes depending on the DC voltage applied. Sample: R(R1) Characteristics 0.1μF, Rated Voltage 50VDC Please consider the DC voltage characteristics when a capacitor is selected for use in a DC circuit.
Page 13 Caution ■Soldering and Mounting 1.Mounting Position 1. Confirm the best mounting position and direction that minimizes the stress imposed on the capacitor during flexing or bending the printed circuit board. 1-1.Choose a mounting position that minimizes the stress imposed on the chip during flexing or bending of the board. 　...
Page 14 Caution 3.Maintenance of the Mounting (pick and place) Machine 1. Make sure that the following excessive forces are not applied to the capacitors. 1-1. In mounting the capacitors on the printed circuit board, any bending force against them shall be kept to a minimum to prevent them from any damage or cracking.
Page 15 Caution 4-1.Reflow Soldering 1. When sudden heat is applied to the components, the [Standard Conditions for Reflow Soldering] mechanical strength of the components will decrease because a sudden temperature change causes deformation inside the components. In order to prevent Temperature(℃) Soldering mechanical damage to the components, preheating is Peak Temperature...
Page 16 Caution 4-2.Flow Soldering 　　　　　[Standard Conditions for Flow Soldering] 1. Do not apply flow soldering to chips not listed in Table 2. Temperature(℃) Table 2 Soldering Soldering Chip Dimension Peak Series Temperature Differential Gradual Temperature (L/W)　Code ΔT Cooling Preheating ΔT≦150℃ Peak GC□...
Page 17 Caution 4-3.Correction of Soldered Portion When sudden heat is applied to the capacitor, distortion caused by the large temperature difference occurs internally, and can be the cause of cracks. Capacitors also tend to be affected by mechanical and thermal stress depending on the board preheating temperature or the soldering fillet shape, and can be the cause of cracks.
Page 18 Caution 5.Washing Excessive ultrasonic oscillation during cleaning can cause the PCBs to resonate, resulting in cracked chips or broken solder joints. Take note not to vibrate PCBs. 6.Electrical Test on Printed Circuit Board 1. Confirm position of the support pin or specific jig, when inspecting the electrical performance of a capacitor after mounting on the printed circuit board.
Page 19 Caution (1) Example of a suitable jig [In the case of Single-side Mounting] An outline of the board separation jig is shown as follows. Recommended example: Stress on the component mounting position can be minimized by holding the portion close to the jig, and bend in the direction towards the side where the capacitors are mounted. Not recommended example: The risk of cracks occurring in the capacitors increases due to large stress being applied to the component mounting position, if the portion away from the jig is held and bent in the direction opposite the side where the capacitors are mounted.
Page 20 Caution (3) Example of Router Type Separator [ Outline Drawing ] Router The router type separator performs cutting by a router rotating at a high speed. Since the board does not bend in the cutting process, stress on the board can be suppressed during board separation.
Page 21 Caution ■ Others 1. Under Operation of Equipment 1-1. Do not touch a capacitor directly with bare hands during operation in order to avoid the danger of an electric shock. 1-2. Do not allow the terminals of a capacitor to come in contact with any conductive objects (short-circuit). Do not expose a capacitor to a conductive liquid, inducing any acid or alkali solutions.
Page 22 Notice ■ Rating 1.Operating Temperature 1. The operating temperature limit depends on the capacitor. 1-1. Do not apply temperatures exceeding the maximum operating temperature. It is necessary to select a capacitor with a suitable rated temperature that will cover the operating temperature range. It is also necessary to consider the temperature distribution in equipment and the seasonal temperature variable factor.
Page 23 Notice ■Soldering and Mounting 1.PCB Design 1. Notice for Pattern Forms 1-1. Unlike leaded components, chip components are susceptible to flexing stresses since they are mounted directly on the substrate. They are also more sensitive to mechanical and thermal stresses than leaded components. Excess solder fillet height can multiply these stresses and cause chip cracking.
Page 24 Notice 2. Land Dimensions Chip Capacitor 2-1. Chip capacitors can be cracked due to the stress Land of PCB bending , etc. if the land area is larger than needed and has an excess amount of solder. Please refer to the land dimensions in table 1 for flow soldering, table 2 for reflow soldering.
Page 25 Notice 3. Board Design When designing the board, keep in mind that the amount of strain which occurs will increase depending on the size and material of the board. Relationship with amount of strain to the board thickness, length, width, etc.] ε= Relationship between load and strain 2Ewh...
Page 26 Notice 5.Flow Soldering ［As a Single Chip］ Set temperature and time to ensure that leaching of the terminations does not exceed 25% of the chip end area as a single chip (full length of the edge A-B-C-D shown at right) and 25% of the length A-B shown as Termination mounted on substrate.
Page 27 Notice ■ Others 1.Transportation 1. The performance of a capacitor may be affected by the conditions during transportation. 1-1. The capacitors shall be protected against excessive temperature, humidity and mechanical force during transportation. (1) Climatic condition 　･ low air temperature : -40℃ ･...
Page 28 NOTE 1.Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. 2.Your are requested not to use our product deviating from this product specification. 3.We consider it not appropriate to include any terms and conditions with regard to the business transaction in the product specifications, drawings or other technical documents.

This manual is also suitable for:

Gcd219r72a332ka01j