Advertisement
Installer Guide
7330 Wireless Remote Humidity Sensor
Please read all instructions before proceeding.
The wireless remote humidity sensor monitors the humidity passing through the
return air plenum and transmits the humidity data wirelessly to the thermostat.
The sensor can be used to view the current humidity level or to control external
humidification or dehumidification equipment. One wireless remote humidity
sensor can be connected.
1 Specifications
Operating Temperature: 14 - 140 ˚F
Storage Temperature: 14 - 140 ˚F
Operating Humidity: 5 - 95% Rh
Blue LED Indicator
- 1 flash every 30 seconds:
- 3 flashes every 10 minutes: Sending sensor data to thermostat
- 1 flash every 2 seconds:
- Solid for 60 seconds:
Red LED Indicator
- 1 flash every 10 seconds:
NOTE: LED indicators are only visible with the sensor cover off.
AC Power: 24 Volt AC
Terminations: Rc, C, H1, H2, D
Normal operation
Sensor is in pairing mode
Successfully paired remote sensor
Lost communication with thermostat
®
smart connect
7330-100-01
TM
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Braeburn 7330
Summary of Contents for Braeburn 7330
- Page 1 ® Installer Guide smart connect 7330 Wireless Remote Humidity Sensor Please read all instructions before proceeding. The wireless remote humidity sensor monitors the humidity passing through the return air plenum and transmits the humidity data wirelessly to the thermostat. The sensor can be used to view the current humidity level or to control external humidification or dehumidification equipment.
-
Page 2: Installation
2 Installation The remote humidity sensor should be mounted in an accessible location on the RETURN RETURN air duct at least 15 inches from AIR PLENUM any duct bends. Wiring is typically run through the return air ductwork to the sensor. 1. -
Page 3: Terminal Description
3 Wiring Remote Sensor The wireless remote humidity sensor communicates wirelessly with the thermostat, however it requires 24 VAC for power and also requires wires to connect to your humidification or dehumidification equipment. Connect your wires as shown. NOTE: The thermostat needs to be configured to control the humidification and/or dehumidification equipment connected to the humidity sensor. - Page 4 Fan Powered Humidifier R C H1 H2 D 120 Volts Constant 24 VAC Switched from HVAC w/Furnace Transformer Operation Dehumidifier R C H1 H2 D Constant 24 VAC 24 VAC Control Relay from HVAC for Dehumidifier or Transformer Outside Air Control Installer Guide...
- Page 5 4 Pairing Remote Sensor See thermostat Installer Guide for additional information on pairing sensors. 1. Enter the wireless setup mode on the thermostat you wish to pair with the remote sensor. Proceed until you see the word SENS in the display with a flashing symbol.
-
Page 6: Communication Loss
Replacing a Sensor – If you are replacing a wireless remote sensor that is paired with an existing thermostat, you will need to clear the thermostats remote sensor settings before pairing the new wireless remote sensor. 1. Install your new wireless remote sensor. 2. - Page 7 FCC Compliance Statement (Part 15.19) (USA only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation. FCC Warning (Part 15.21) (USA only) Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
-
Page 8: Limited Warranty
2215 Cornell Avenue Montgomery, IL 60538 ® Braeburn Systems LLC 2215 Cornell Avenue • Montgomery, IL 60538 Technical Assistance: www.braeburnonline.com 844-BLU-LINk (844-258-5465) (U.S.) 630-844-1968 (Outside the U.S.) 7330-100-01 ©2015 Braeburn Systems LLC • All Rights Reserved • Made in China.
Need help?
Do you have a question about the 7330 and is the answer not in the manual?
Questions and answers