1. Manuals
  2. Brands
  3. RED BAND Manuals
  4. Construction Equipment
  5. SCREEDEMON WS500
  6. Operator's safety and service manual

RED BAND SCREEDEMON WS500 Operator's Safety And Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
O
PERATOR
S
AND
ERVICE
S
CREE
This manual covers the following serial numbers
and higher for each model listed:
WS500 . . . . . . . . . . . . . . . . . . . 141030
W
S
ET
CREED
RED BAND UK LTD
Unit 41­45 • The Warren
East Goscote Ind. Est.
East Goscote • Leicester
LE7 3XA
'
S
S
M
D
EMON
Tel: 0116 260 2601
Fax: 0116 260 2603
sales@redbanduk.co.uk
www.redbanduk.co.uk
AFETY
ANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SCREEDEMON WS500 and is the answer not in the manual?

Questions and answers

Summary of Contents for RED BAND SCREEDEMON WS500

  • Page 1 WS500 ....141030 CREED RED BAND UK LTD Unit 41­45 • The Warren Tel: 0116 260 2601 East Goscote Ind.

  • Page 3: Table Of Contents

    ABLE ONTENTS Safety Information ..... . 1 Maintenance Schedule......7 Engine Maintenance.
  • Page 4 This page intentionally left blank.

  • Page 5: Safety Information

    AFETY NFORMATION Introduction SAFE DRESS: Do not wear loose clothing, rings, wristwatches, etc. near machinery. This Safety Alert Symbol is used to call attention to items or operations which may be dangerous to those operating or working with this NOISE PROTECTION: Wear OSHA specified equipment.

  • Page 6: Patent Pending

    PATENT PENDING 01504 EXCITER LOCATION 17768 EXCITER LOCATION 17768 17769 Safety Decals (Decal Set #17782) - 2 -...

  • Page 7: Specifications

    PECIFICATIONS 500H 500R Operating Weight 29 lbs (13.2 kg) 29 lbs (13.2 kg) Engine Make Honda Robin Engine Mode GX31TA2 EH035V Maximum Rated Power 1.5 Hp (1.12 kW) @7000 rpm 1.6 Hp (1.18 kW) @7000 rpm Displacement (1.9 in ) 31 cm (2.04 in ) 33.5 cm Spark Plug...

  • Page 8: Operation

    PERATION Introduction Red Band equipment is intended for use in very severe applications. They are powered by four cycle engines and are available in different sizes and a selection of engines. Bolt This parts manual contains only standard parts. Variations of these parts as well as other special parts are not included.

  • Page 9: Operation

    Operation Before placing the ScreeDemon in concrete make sure the Blade Length clamps securing the exciter to the float blade are tight. CAUTION Keep the blade clamps tight at all times. Operat- ing the ScreeDemon with the clamps loose will damage the float blade.

  • Page 10: Handle Adjustment

    Handle Adjustment The operator can adjust the handle on the Handle ScreeDemon to a comfortable position. Adjustment Knob Refer to Figure 2. Loosen the handle by turning the handle adjustment knob counter-clockwise. Move the handle to the desired position. Kickstand Tighten the handle adjustment knob.

  • Page 11: Maintenance

    AINTENANCE WARNING CAUTION Always exercise the stopping procedure before Always verify fluid levels and check for leaks after servicing or lubricating the unit. changing fluids. After servicing the unit, replace and fasten all Do not drain oil onto ground, into open streams, guards, shields, and covers to their original or down sewage drains.

  • Page 12: Service

    ERVICE Engine Mounting Flange Removal Assembly and disassembly should be performed by a service technician who has been factory trained on MBW Refer to Engine and Engine Mount, page 16. equipment. The unit should be clean and free of debris. Cleaning unit before disassembly is recommended.

  • Page 13: Exciter Assembly

    Loosen the three socket head cap screws (#13) Apply a small bead of Loctite 426 adhesive (MBW securing the exciter cover (#8) to the exciter housing. #17885) to the lip on the engine mounting flange. Back the socket head cap screws out about 1/4”. See Figure 4.

  • Page 14: Parts Replacement Cycles And Tolerances

    Parts Replacement Cycles and Tolerances Replace anytime a bearing is rough, binding, discolored or removed from housing or Bearings shaft. Engine Components Refer to your engine manufacturer’s Owner’s Manual. Replace any worn or damaged hardware as needed. Replacement hardware should Hardware be grade 5 and zinc plated unless otherwise specified.

  • Page 15: Contact Information

    Write Serial Number here Write Model Number here shockmount bolt. Write Serial Number here Contact Information RED BAND UK LTD Unit 41­45 • The Warren Tel: 0116 260 2601 East Goscote Ind. Est. Fax: 0116 260 2603 East Goscote • Leicester sales@redbanduk.co.uk...

  • Page 16: Main Assembly

    Main Assembly - 12 -...
  • Page 17 ITEM PART NO. DESCRIPTION 18472 GRIP, HANDLE 17170 SHOCKMOUNT, 2” OD X 1-3/4” LONG 17245 DOWEL PIN, 1/4” X 1.75” 17263 LEVER, THROTTLE 17639 WASHER, SEALING 17647 KNOB, CLAMPING 17649 CLAMP 17651 STUD, 1/2-13 X 1-1/2” LONG 17653 MOUNT, HANDLE 17656 HANDLE, LIFTING 17660...

  • Page 18: Exciter Assembly

    Exciter Assembly - 14 -...
  • Page 19 ITEM PART NO. DESCRIPTION 06237 O-RING, 4.33 ID X 0.103 17170 SHOCKMOUNT, 2” OD X 1-3/4” LONG 17629 HOUSING, EXCITER 17640 BEARING, BALL 17643 SHOCKMOUNT, 1” OD X 1” LONG 17645 COVER, EXCITER 18547 KIT, CLAMPS (INCLUDES TWO CLAMPS AND ALL NECASSARY HARDWARE) 17736 NUT, SQUARE, 3/8”-16 17863...

  • Page 20: Engine And Engine Mount

    Engine and Engine Mount - 16 -...
  • Page 21 ITEM PART NO. DESCRIPTION 09618 FITTING, PLUG 15304 SOCKET HEAD CAP SCREW, M6 X 25mm 17296 SWITCH, ENGINE STOP 17634 FLANGE, ENGINE MOUNT 17635 BEARING, BALL 17636 SHAFT (DOES NOT INCLUDE ITEM 7) 17637 STUD, 1/4”-20 X 3/4” 17709 ENGINE, HONDA GX31TA2 17792 ENGINE, ROBIN EH035V 17711...

  • Page 22: Warranty

    The cost of transportation and other expenses assume for us any other liability or warranty in Red Band reserves the right to inspect and render fi nal connected therewith are not covered by this warranty. connection with the sale or service of any of our decision on each warranty case.

Table of Contents