Advertisement
PG-04
1-1 PG-04 Appearance
1-2 Explanations of the terminals of PG-04 Card
Terminals
VP
DCM
A1,
A1
B1,
B1
Z1,
Z1
A2,
A2
B2,
B2
A/O, B/O,
Z/O
Pulse Generator Card for VFD-V Series
Instruction Sheet
Input terminal
CH1
A1
B1
A1
B1
Output voltage of encoder: +12V±5% 200mA
Common point of the power supply and the signal
The input signal of encoder (select output type of the encoder from FJP1)
The power supply can be single-phase and 2-phase and the Max. is
500KP/Sec.
The input signal of encoder (select output type of the encoder from FJP4)
The power supply can be single-phase and 2-phase and the Max. is
500KP/Sec.
The output signal of encoder can set the dividing frequency by using
parameter 10-20.
The Max. output of Open Collector is DC24V 100mA.
Grounding
Pulse input terminal
CH2
Power
Z1
VP
Z1
A2
A2
B2
B2
Explanation
1
Advertisement
Table of Contents
Related Manuals for Delta Electronics Pulse Generator Card PG-04
Summary of Contents for Delta Electronics Pulse Generator Card PG-04
- Page 1 PG-04 Pulse Generator Card for VFD-V Series Instruction Sheet 1-1 PG-04 Appearance 1-2 Explanations of the terminals of PG-04 Card Terminals Output voltage of encoder: +12V±5% 200mA Common point of the power supply and the signal The input signal of encoder (select output type of the encoder from FJP1) The power supply can be single-phase and 2-phase and the Max.
- Page 2 1-3 Wiring Notes 1. Using the shielded wire to prevent interference, and do not line up in parallel with circuits of AC200V or above. 2. Recommended wire size: 0.21~0.81mm 3. Wire length The Output Types of the Encoder Max. Wire Length Voltage Open Collector Line Driver...
-
Page 3: Wiring Examples
1-4 Wiring Examples Wiring Diagram 1 Non-Fuse breaker FWD/STOP REV/STOP Multi-step1 Multi-step2 Multi-step3 Multi-step4 Reset E.F. Digital common 10-08 10-12 Line driver Main circuit (power) terminals Jumper Braking Resistor(Option) +1 +2/B1 B2 R/L1 U/T1 V/T2 S/L2 W/T3 T/L3 Control circuit terminals Motor Line driver Line driver encoder... - Page 4 Wiring Diagram 2 Non-Fuse breaker FWD/STOP REV/STOP Multi-step1 Multi-step2 Multi-step3 Multi-step4 Reset E.F. Digital common EH-PLC Phase difference 90 Main circuit (power) terminals Recommended Wiring for Resistors Pull High Resistor 330 330 330 Jumper Braking Resistor(Option) +1 +2/B1 B2 R/L1 U/T1 V/T2 S/L2...
- Page 5 1-5 Installation For 1-5HP Step 1: Insert 3 PCB supports into control board. Step 2: Press the PG card on the control board to be fixed to tighten the 3 screws with a torque of 4-6kgf-cm. If the PG card is not fixed on the control board, it may cause screw idle running and cannot turn the screw into supports.
- Page 6 1-6 The corresponding output types of encoder Output Types of the Encoder ASIA DELTA ELECTRONICS, INC. TAOYUAN Plant/ 31-1, SHIEN PAN ROAD, KUEI SAN INDUSTRIAL ZONE TAOYUAN 333, TAIWAN, R.O.C TEL: 886-3-362-6301 FAX: 886-3-362-7267 FJP1 NORTH/SOUTH AMERICA DELTA PRODUCTS CORPORATION Sales Office/ P.O.
Need help?
Do you have a question about the Pulse Generator Card PG-04 and is the answer not in the manual?
Questions and answers