Advertisement
Model CSF Gas Countertop Model Fryers
WARNING ! : I
OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE
,
INSTALLATION
OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE
INSTALLING OR SERVICING THIS EQUIPMENT
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE
VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER
Please call the Service Department and ask for contact information for your local
11990 Rivera Rd. Santa Fe Springs, CA 90670
Telephone:(714) 547-9218
MPROPER INSTALLATION
FOR YOUR SAFETY
APPLIANCE.
service company.
www.connertoncooking.com
Installation,
Operation &
Maintenance
Instructions
,
,
ADJUSTMENT
,
INJURY OR DEATH
.
(562) 464 - 9901
,
ALTERATION
SERVICE
. R
EAD THE
1
Advertisement
Table of Contents
Summary of Contents for Connerton CSF Series
- Page 1 Installation, Operation & Maintenance Instructions Model CSF Gas Countertop Model Fryers WARNING ! : I MPROPER INSTALLATION ADJUSTMENT ALTERATION SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE INJURY OR DEATH EAD THE INSTALLATION OPERATING AND MAINTENANCE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER...
- Page 2 NOTICE Unit must be level to assure maximum performance. Improper leveling may void warranty. WARNING ! If disconnection of the restraint is necessary to move the appliance for cleaning, etc., reconnect it when the appliance is moved to its original installed position. WARNING ! All fryers must be restrained to prevent tipping to avoid the splashing of hot liquid.
- Page 3 WARNING ! There must be adequate clearance between fryer(s) and construction. Clearance must also be provided in front for servicing and for operation. Installation in Non-combustible locations only LL GAS MODEL FRYERS SHALL BE INSTALLED WITH AT LEAST A INCH SPACE BETWEEN THE FRYER AND SURFACE FLAMES FROM ADJACENT EQUIPMENT FLAME GUARD IS ACCEPTABLE IF ALLOWED UNDER LOCAL CODE...
- Page 4 Due to the variety of problems that can be caused by outside weather conditions, venting by canopies or wall fans is preferred over any type of direct venting. It is recommended that a canopy extend 6” past the appliance and the bottom edge be located 6’ 6” from the ○...
- Page 5 An adequate gas supply is imperative. Undersized or low-pressure lines will restrict the volume of gas necessary for satisfactory performance. A combination gas valve and pressure regulator, which is provided with each unit, is set to maintain a 4” W.C. manifold pressure for natural gas or 10.0”...
-
Page 6: Operation
Connect the gas supply directly to the ½” male NPT connector located near the lower left rear corner of the fryer. When tightening the supply pipe, be sure to hold the matting connector extending from the unit securely with a wrench. This will prevent any damage or distortion to the internal piping and controls of the unit. -
Page 7: Shutdown Procedure
knob is released, repeat the lighting procedure and keep the knob down longer. Adjustment of pilot flame may be necessary. 4. When the pilot stays lit, turn the knob counter clockwise to the “ON” position. Do not press down on the knob in this step. 5. - Page 8 Diagrams Note: High limit Shown tripped.
- Page 9 Wiring Diagram...
- Page 10 IMIT ONTROL Gas floor model fryers are equipped with a secondary heat control that prevents the oil ○ temperature from rising above 450 F. (Because of the accuracy tolerance of the ○ sensor, the oil temperature may reach as high as 475 In the event the fryer shuts down due to this condition, the oil must be cooled to below ○...
- Page 11 CSF-Shallow Fryer Diagram CSF – Shallow Fryer Parts List 10-150-00 Burner CSG-03 Gas Valve CSF36-163 Magnet CSF36-A160 Pilot Access weld assembly CSG-05 Pilot CSF36-168 Knob, Thermostat 00-100-40 Orifice CSG-04 Thermostat CSG-02 High-limit switch 10 CSG-19 Thermopile...
-
Page 12: Daily Cleaning
Effective January 2020 CONNERTON (Company) warrants to the original owner that the product be free from defects in materials and/or workmanship. This warranty shall apply to units properly installed in a static location only and be in effect for two (2) years from the date of purchase but shall not exceed 30 months from the date of shipment from the Company. - Page 13 The use of only authorized servicers for needed repairs. PROCEEDURES FOR REQUESTING WARRANTY SERVICE All services must be prearranged by the Company prior to works being performed. Contact CONNERTON service department at (714)-547-9218 furnish complete model and serial numbers and a copy of the purchase invoice and describe nature of the problem.
Need help?
Do you have a question about the CSF Series and is the answer not in the manual?
Questions and answers