Titan Attachments ATVWC5 Operator's Manual

Towable wood chipper

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

TOWABLE WOOD CHIPPER

ATVWC5

198269

Operator's Manual

Read the Operator's Manual entirely. When you see this

symbol, the subsequent instructions and warnings are

serious follow without exception. Your life and the lives

of others depend on it!

Table of Contents

Need help?

Do you have a question about the ATVWC5 and is the answer not in the manual?

Questions and answers

Summary of Contents for Titan Attachments ATVWC5

Page 1 TOWABLE WOOD CHIPPER ATVWC5 198269 Operator’s Manual Read the Operator’s Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious follow without exception. Your life and the lives of others depend on it!
Page 2 PART 1: GENERAL SAFETY RULES WARNING Read this Safety & Operating Instructions manual before you use the Woodchipper. Become familiar with the operation and service recommendations to ensure the best performance of your machine. CAUTION This machine is designed solely to chip wood and must not be used for any other purpose.
Page 3: Protecting Yourself And Those Around You
G. DO NOT operate inside a building or confined space or Climb on the in-feed chute. PROTECTING YOURSELF AND THOSE AROUND YOU WARNING This is a high-powered machine, with moving parts operating with high energy. You must operate the machine safely. Unsafe operation can create a number of hazards for you, as well as anyone else in the nearby area.
Page 4: General Safety
B. Store all fuel and oil in containers specifically designed and approved for this purpose and keep away from heat and open flame, and out of the reach of children. C. Replace rubber fuel lines and grommets when worn or damaged and after 5 years of use.
Page 5 machine could cause personal injuries and property damage and will invalid your warranty. G. If the machine starts to make an unusual noise or vibrate, shut down the engine, disconnect the spark plug wire, keeping it away from the spark plug to prevent accidental starting, wait 5 minutes for engine to cool down, then inspect for damage.
Page 6: A Note To All Users
A NOTE TO ALL USERS List of warnings and cautions cannot be all-inclusive. If situations occur that are not covered by this manual, the operator must apply common sense and operate this WOODCHIPPER in a safe manner. Contact the dealers for assistance in your area PART 1: GENERAL SAFETY RULES (CONT) SAFETY LABELS FOUND ON YOUR UNIT...
Page 7: Technical Specifications
PART 2: FAMILIAR WITH THE WOODCHIPPER TECHNICAL SPECIFICATIONS RECOIL START ELECTRIC START ENGINE 13HP/15HP FOUR 13HP/15HP FOUR STROKES STROKES POWER GASOLINE/PETROL GASOLINE/PETROL CHIPPER CAPACITY 4CBM/HOUR TO 4CBM/HOUR TO 6CBM/HOUR 6CBM/HOUR WOOD DIAMETER DIAMETER 120MM DIAMETER 120MM PERMITTED WOOD 310MM 310MM WIDTH CHIPPER BLADE TWIN REVERSIBLE BLADES...
Page 8 PART 3: OPERATING THE WOODCHIPPER WARNING A. Read and understand all instructions, safety precautions, and/or warnings listed in “PART I: General Safety Rules” before operating the WOODCHIPPER. If any doubt or question arises about the correct or safe method of performing anything found in this manual, please contact the dealers in your area.
Page 9 OPERATOR ZONE WOOD CHIPPING NOTICE Woods and branches’ diameter should be no bigger than 120mm. WARNING Do not place your hands into the chute when loading. This is a very UNSAFE method and could result in injury to your hands. Do not reach or step across the rail while the Woodchipper is running.
Page 10: Belt Adjustment And Replacement
BELT ADJUSTMENT AND REPLACEMENT If you need to adjust the tightness of the belts or replace old belts, please follow the steps below: Step 1: Unscrew the 4 “Bolts” from the belt cover and remove the belt cover from the machine. Step 2: Remove the old belts and replace with new belts.
Page 11: Blade Replacement
BLADE REPLACEMENT If you need to replace old blade or use another edge of the blade, please follow the steps below: Step 1: Remove the "Bearing cover" and open or remove the "Infeed hopper". Step 2: Use "Special Spanner" to rotate the drum to proper position where you can see the blade that needs to be replaced or adjusted clearly as shown in the figure below.
Page 12: Blade Adjustment
Step 3: (WITH CAUTION) Use the "T-Socket" tool to unscrew the 5 "Blade bolts". Once the blade is replaced and in position, tighten the 5 "Blade bolts". BLADE ADJUSTMENT If needed, adjust the “Gap” between the “Blade” and “Anvil” as shown in the figure below: (Usually the smaller one of the two "Gap"...
Page 13 As shown in the figure below (viewing from the bottom at the infeed hopper side): Step 1: Loosen the 5 "Anvil bolts". Step 2: Use the "Adjust bolts" to adjust the position of the "angle bar" until the gap between the "Anvil"...
Page 14: Engine Service
PART 4: MAINTAINING THE WOODCHIPPER Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer’s user manual for maintenance procedures. WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool.
Page 15: Part 5: Troubleshooting And Parts List
LUBRICATION NOTICE All Bearings of your Chipper are sealed units and should have sufficient lubricant to last the life of your machine with normal use. PART 5: TROUBLESHOOTING AND PARTS LIST WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five minutes to allow all parts to cool.
Page 16 Machine does not The belts may be too loose and slipping. Adjust or replace ➢ seem belts as needed. to have full chipping power.
Page 17: Explosion View
EXPLOSION VIEW DESCRIPTION DESCRIPTION FOUNDATION IN-FEED ROLLER EMERGENCY STOP FIXATION BLADE RUBBER FIXATION WHEEL AXIS EMERGENCY STOP SWITCH WHEEL SPRING PULLEY RUBBER BELT SWITCH BELT COVER SWITCH COVER CLUTCH ANGLE BAR BELT INNER COVER IN-FEED EXTENSION BEARING HANDLE BEARING FIXATION PLATE SWITCH EXTENSION SUPPORT FOOT FLANGE...
Page 18 ACKNOWLEDGEMENT OF RISK AND RELEASE OF LIABILITY The use of any equipment, including this one, involves the potential risk of injury. Apart from any warranty claim that might be presented for a claimed defect in material or workmanship of the product, you accept and assume full responsibility for any and all injuries, damages (both economic and non- economic), and losses of any type, which may occur, and you fully and forever release and discharge Titan, its insurers, employees, officers, directors, associates, and agents from any and all claims,...

This manual is also suitable for:

198269