Renu Electronics FL055-0808N-V2 Manual

FL055-0808N-V2 &
FL005-0808N-V2
FL055-0808N-V2: Is base PLC model from FlexiLogics family.
It has inbuilt 8 digital inputs and 8 digital NPN type outputs
with 2 serial ports, one USB Type C, one Ethernet port. The
model can be expanded up to 16 I/O modules.
FL005-0808N-V2: This is a base PLC model from FlexiLogics
family. It has inbuilt 8 digital inputs and 8 digital NPN type
outputs with 2 serial ports, one USB Type C port. This model
can be expanded up to 16 I/O modules. This model does not
have an Ethernet port.
System Components:
- FL055-0808N-V2 or FL005-0808N-V2
- Installation Kit: 2 Locking Connectors, 2 DIN rail sliders.
PRODUCT DIMENSIONS
SPECIFICATIONS
Power Supply 24VDC (±15%), 110mA
Isolation Non-Isolated
Memory
Total Program Memory 8 MB + 2 MB
(Application+ Ladder/Logic)
Program Capacity 50K Steps
Keep Memory Registers 10752 WORDS (FRAM)
Communication Ports
COM1 (RJ45) RS232, for Programming & Communication
COM2 (Open terminals) 2-wire RS485 for Communication
Ethernet* (FL055 only) 10/100Mbps, for
upload/download/Communication
USB 1 x USB Type C
Expansions
Expansion IO capacity 16 Expansions modules, 256 I/O ports
Local IO Specification
Number of Inputs 8 Inputs [Bi-directional type]
Input Design According to the EN 61131-2 type 1
ON Voltage Minimum : 15VDC, Maximum: 30VDC
OFF Voltage Minimum : -3VDC, Maximum: 5VDC
Nominal Input 24VDC, 5mA typical
Isolation Optically isolated from internal circuit
High isolation voltage (BV= Greater than
1I bk
1.5KV)
Input Response Time ON: 10msec, OFF: 10msec
Input Impedance 4.8KΩ
High Speed Channels High Frequency 200kHz: 4 Pairs (X0-X1, X2-
Single Phase Counter X3, X4-X5 & X6-X7) or
Low Frequency 25kHz: 8 (X0-X7)
Quadrature Channels High Frequency 200kHz: 4 Pairs (X0-X1, X2-
X3, X4-X5 & X6-X7)
Max. Input Count 4294967295 (32 Bit)
Number of Outputs 8 (NPN Transistor type), within which 4
Outputs are PWM type
4 PWM Output Y0(Pulse 200kHz), Y1(for Direction of Y0),
Y2(Pulse 200kHz), Y3(for Direction of Y2),
Y4(Pulse 200kHz), Y5(for Direction of Y4),
Y6(Pulse 200kHz), Y7(for Direction of Y6)
ON Output Voltage Min ON: 22VDC (Voltage across load)
Max. ON: 30VDC (Voltage across load)
Nominal Output Voltage 24VDC
Nominal Output Current 250mA typical per channel
Output Response Time ON: 10µsec, OFF: 10µsec
Nominal Load Max. 96Ω/6W (resistive) @24VDC
5VA(inductive)
Environment & Approvals
Operating Temperature 0 to 55°C
Humidity 10 to 90% (Non-Condensing)
25g, 11ms, Half Sine wave, 3 mutually
Shock Circuit Protection
perpendicular axes
5 to 150Hz, displacement of 0.3mm
Vibration (peak to peak), 3G, 3 mutually
perpendicular axes
Approvals CE, RoHS
PANEL MOUNTING
FIG-1: Pull up the sliders (highlighted) provided with the unit
towards outward direction as shown.
FIG-2: Rest the unit on the DIN rail plate.
FIG-3: Press the highlighted connector into the downward
direction to lock it same connector from the downside of the
product press upward direction. Locking connector helps the
two units (FL base & expansion) to hold each-other properly on
the DIN rail plate.
FIG-4
FIG-4: Two slots to grip the locking connector are provided on
the case highlighted by RED circle, pulled the connector.
FIG-5: Lock connector provided with base module unit as shown
to the Expansion module.
FIG-5