Related Manuals for Amer WAP3x Series
Summary of Contents for Amer WAP3x Series
- Page 1 WAP33DC and WAP38DC Wireless Indoor Access Point Installation Manual Manual Version: v2.0...
-
Page 2: Table Of Contents
WAP3x Series Wireless Indoor AP Installation Manual Content Content Chapter 1 Device Introduction ..........1-1 Chapter 2 Preparation for Installation ........2-1 2.1 Installation Precautions ................. 2-1 2.2 Installation Environment Requirements..........2-1 2.3 Equipment Accessories................2-1 2.4 Installation Tools ..................2-2 Chapter 3 AP Installation ............ -
Page 3: Chapter 1 Device Introduction
WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 1 Device Introduction Chapter 1 Device Introduction The WAP3xDC series metal indoor wireless access points includes the WAP33DC and WAP38DC: Fig 1-1 WAP33DC WAP38DC Fig 1-2... - Page 4 WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 1 Device Introduction Quick Specs: Product Model WAP33DC WAP38DC Features IEEE802.11a/b/g/n IEEE802.11a/b/g/n Double Radio frequency Double Radio frequency Built-out antenna: 2.4G gain 5dBi, Built-in antenna: 2.4G gain 4dBi, Antenna 5G gain 5dBi 5G gain 5dBi Power Consumption...
-
Page 5: Chapter 2 Preparation For Installation
WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 2 Preparation for Installation Chapter 2 Preparation for Installation 2.1 Installation Precautions Before the installation and configuration, please read the related security introduction carefully. Use the appropriate security measures to avoid personal injury and equipment damage. -
Page 6: Installation Tools
WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 2 Preparation for Installation 2.4 Installation Tools Recommended tools to use when installing WAP3xDC series access points: Horizontal Permanent Knife Wire Network pliers ruler marker stripper Impact drill (1) Rubber Phillips Ladder and some hammer screwdriver... -
Page 7: Chapter 3 Ap Installation
WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 3 AP Installation Chapter 3 AP Installation 3.1 Installation Process Fig 3-1 AP installation flow diagram... -
Page 8: Installation Checklist
WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 3 Installation 3.2 Installation Checklist Check the following items before installing the AP: Power on the AP and connect the Ethernet cable. Inspect the LED status to make sure the AP is working normally. Record AP’s MAC address and serial number (MAC address and serial numbers are located on the back of the AP). -
Page 9: Wall Hanging Installation
WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 3 AP Installation 3.4.1 Wall Hanging Installation Use the wall mounting bracket and the supporting expansion bolts and screws if you plan to install the device to a wall. Fig 3-2 wall mounting bracket size and block diagram (unit: mm) If you choose to install the AP using the wall hanging method, we recommend connecting the Ethernet cable to the AP first and then install the AP to the wall mounting bracket. - Page 10 WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 3 AP Installation Match the screw holes to the expansion bolt holes on the wall. The screws should pass through the installation holes of the wall mounting kit. Lock the wall mounting kit to the wall.
- Page 11 WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 3 AP Installation Fig 3-5 hang WAP33DC AP to the wall mounting bracket 1: AP 2: Wall Mounting Bracket The same method applies to the WAP38D: Fig 3-6 WAP38DC back mounting holes...
- Page 12 WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 3 AP Installation Fig 3-7 WAP38DC to the wall mounting bracket (5) Finally, on the WAP33DC, lock the stationary blanks of the chassis to the AP and screw the wall mounting bracket using the M3 screws Fig 3-8 Stationary blanks of the chassis to the wall mounting bracket 1: stationary blanks of the chassis 2: M3 Screw...
-
Page 13: T-Keel Installation
WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 3 AP Installation 3.4.2 T-keel Installation 1. The width of T-keel is from 12mm to 30mm. 2. This installation method is only applied to the T-keel The square hole on the rail in the wall mounting kit will be used for this method: Fig 3-9 T-keel Installation 1: T-keel Mounting Kit 2: Wall Mounting Kit... - Page 14 WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 3 AP Installation (1) Set the T-keel mounting kit into the rail of the wall mounting kit and place the M3x7 fastening screws through the rail hole of the T-keel mounting kit. Fig 3-10 Keel bracket to the T-keel 1: Wall Mounting Kit 2: Square Hole of the Rail...
- Page 15 WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 3 AP Installation (3) Slide the T-keel mounting kit according to the direction in the following picture. Screw the M3x7 until the T-keel mounting kit is firmly locked in. Fig 3-12 T-keel mounting kit 2: T-keel mounting kit 3: M3×8 fastening screws (4) Use the four M3x7 fastening screws under the T-keel until the T-keel is firmly locked...
- Page 16 WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 3 AP Installation Fig 3-14 WAP38DC installation (7) Close the stationary blanks of the chassis to the AP device using the M3 screws. Fig 3-14 complete the AP installation (8) Connect AP to the wired LAN/POE by using the cable.
-
Page 17: Ap Power Options
WAP3xDC Series Wireless Indoor AP Installation Manual Chapter 3 AP Installation 3.5 AP Power Options The WAP3xDC series supports both local power and PoE. WAP33DC adopts the 802.3af/802.3at PoE power supply. WAP38DC adopts the 802.3af/802.3at PoE power supply. Table 3-1 power adapter specifications Items Explanation Power Adapter Input...
Need help?
Do you have a question about the WAP3x Series and is the answer not in the manual?
Questions and answers