Table of Contents
Advertisement
Quick Links
Left hand swing out, PN 300995
Stand in front of Commander;
door opens away from you.
Left hand swing in, PN 300996
Stand in front of Commander;
door opens towards you.
Electrical Installation Guide
Commander
Automatic Door Opener
Right hand swing out, PN 300993
Right hand swing in, PN 300994
Stand in front of Commander;
door opens towards you.
Door
Hinges
Part No. 000981
09-m10-2013
Stand in front of Commander;
door opens away from you.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Savaria Commander
- Page 1 Commander Automatic Door Opener Left hand swing out, PN 300995 Right hand swing out, PN 300993 Stand in front of Commander; Stand in front of Commander; door opens away from you. door opens away from you. Right hand swing in, PN 300994 Left hand swing in, PN 300996 Stand in front of Commander;...
-
Page 2: Electrical Shock Hazard
Standard notations The following notations may be used throughout this guide to emphasize important safety information, mechanical concerns, and other important information. Savaria recommends that you review and follow all of these messages. Danger messages indicate an imminently hazardous situation, which, if not avoided, results in death or seri- DANGER ous injury. -
Page 3: Table Of Contents
Table 1 List of steps in this guide Step Page Verify factory settings - Commander main board Electrical connections for PAL Electrical connections for Infinity or Eclipse Electrical connections for Voyager Electrical connections for V1504 or Multilift... -
Page 4: Table 2
4 Verify factory settings - Commander main board Step 1 Verify factory settings - Commander main board Purpose To verify the Commander main board factory settings. NOTE The main board configuration is set at the factory. You do not normally need to make adjustments during verification of the initial configuration. - Page 5 Verify factory settings - Commander main board 5 Locate the fuses on the main board. Figure 2 Initial jumper and pot settings Table 4 Main board fuses Fuse Rating 5 Amp, SLO, MDL 3AG 4 Amp, SLO, MDL 3AG Note: Jumper J3 is also installed.
-
Page 6: Electrical Connections For Pal
Connect the Commander harness to one of the PAL main controller board terminals, depending on which Electrical connections for PAL floor the Commander is on – top, middle or bottom. For the top floor, connect the Commander harness to Purpose TDOT. -
Page 7: Electrical Connections For Infinity Or Eclipse
Electrical connections for Infinity or Eclipse 7 Connect the harness from T2 on the Commander board Step 3 to the Micro-6 main controller board connectors J23 to Electrical connections for Infinity or J28 (FL1 to FL6) pins 11 and 12. -
Page 8: Electrical Connections For Voyager
Voyager: connect T2 Voyager main controller board sends an additional signal to the Commander to begin the door open cycle. This safety feature ensures the lock and latch allow the door to open only when the lift is at the floor level that has sent the cab call signal. - Page 9 Voyager 3rd floor rear Voyager 2nd floor front For the 1st floor front landing, connect the 1st floor front harness to T2. Figure 17 1st floor front landing Voyager 1st floor front Part no. 000671 09-m10-2013 Commander Electrical Installation Guide...
- Page 10 2nd floor rear landing Voyager 2nd floor rear 10 For the 1st floor rear landing, connect the 1st floor rear harness to T19. Figure 21 1st floor rear landing Voyager 1st floor rear Commander Electrical Installation Guide Part no. 000671 09-m10-2013...
-
Page 11: Electrical Connections For V1504 Or Multilift
Controller board landing terminal connections (for one or two Commanders) Multilift From Commander board T2 RED GRN Purpose To connect the lift to the Commander for the begin door open signal. Requirements For a V-1504 with more than two Commanders, follow Complete Step 1... -
Page 12: Electrical Connections For Stand-Alone Doors
Commander main board. Step Requirements Complete Step Connect the wiring to the Commander main board TDOB for begin door open signal. Considerations Figure 28 Push button switch terminal connections Use the step-down transformer when the Commander installation is stand-alone and when you want separate power for the Commander. -
Page 13: Electric Strike - Powered By Commander
When possible, run the Commander wiring to the lock cutout in the door frame during door frame construction. Step Connect the wiring to the Commander main board TSS for begin door open signal. TSS-1 ground (black) and TSS-2 hot (red). Figure 30... -
Page 14: Push And Go Cam Adjustment
1'' open and includes the full opening cycle to fully open. This feature allows the Commander to fully open the door once the door is pushed by a person. It activates at 1'' open and substitutes for a wall mounted door opener or a remote control button opener. -
Page 15: Latch Check Cam Adjustment
Installation Guide. Considerations Use needle-nose pliers to rotate the cam. The Latch Check cam contact allows the Commander Ensure the bottom Open Door Limit cam only releases spring to overcome difficult door close conditions. the contact when the door is in the fully open position. -
Page 16: Pot Adjustments
5 Commander main board on page 4 Pots are in midrange position when equidistant locate TDOB on the Commander main board. between the fully left and fully right position. Move the pots a maximum of 1/4 turn at a time... -
Page 17: Remote Control Programming
The remote is made up of the remote control unit transmitter (tx) that you carry and the receiver unit (rx) in the Commander. Usage If the Commander installation is on an elevator or lift 23A 12V battery door, the remote control signal opens the door under the following circumstances: •... -
Page 18: Disconnect Power From Board
To disconnect power from the Commander main board. NOTE You do not need to disconnect the battery during installation. This procedure is not a requirement for Commander installation; use this procedure only during general maintenance or troubleshooting. Initially, the Commander battery terminal is closed. In addition, there is no connection to a step-down... -
Page 19: Remove Board From Main Unit
Commander NOTE You do not need to remove the circuit board during installation. This procedure is not a requirement for Commander installation; use this procedure only during general maintenance or troubleshooting Considerations The board is grounded on its own connector plate. To... - Page 20 Rev. Date: CD40106B MC14093 Date: AND MAY NOT BE USED BY OTHERS WITHOUT PRIOR WRITTEN CONSENT. Drawn by: PRO-II AUTO DOOR/COMMANDER USED CD40106B 1.0nF Document Number: 623393R0 Size OPERATOR BOARD 772393 R000 SHEET Commander Electrical Installation Guide Part no. 000671 09-m10-2013...
- Page 22 Commander Automatic Door Opener for Elevators ELECTRICAL INSTALLATION GUIDE Part No. 000671 © Copyright 2013 Savaria Corporation Lifts and Elevators www.savaria.com Support 2 Walker Drive Brampton, Ontario, L6T 5E1, Canada Toll free: (800) 791-7999 Fax: (905) 791-2222...
Need help?
Do you have a question about the Commander and is the answer not in the manual?
Questions and answers