Subscribe to Our Youtube Channel
Related Manuals for Triad TS-PAS12
Summary of Contents for Triad TS-PAS12
- Page 1 Triad Cinema Subwoofers Installation Guide TS-PAS12/15/18/18DVC Package contents (1) Cinema subwoofer (1) Baffle cover (1) Grille (6) Feet/wall anchors (2) Washers (4) 1" screws for 12" subs (4) 1.25" screws for 15" & 18" subs...
-
Page 2: Installation
Installation 1. Determine if the Triad Cinema subwoofer is being installed vertically or horizontally. Either installation requires four rubber feet for the bottom of the sub and two to act as wall spacers. Note: The horizontal orientation's mounting holes are the width of a standard 16"... - Page 3 Caution: Do not mount the 15 or 18 model subwoofers off the ground. The weight must be supported by the ground, not the wall. 3. Slide out the top two channel covers. Pull the speaker wire (minimum 14 AWG) through the wireway hole and secure them in the subwoofer's binding posts by screwing them down onto the wire.
- Page 4 5. Locate the smaller holes on the back of the enclosure, peel the adhesive off the wall anchors/feet, then align the hole in the anchor with the hole in the sub and attach them. Use wall screws and the included washers to attach the sub to the wall. Note: Wall screws and anchors are not included.
- Page 5 6. Put the channel covers back in place. 7. Attach the baffle cover. If desired, attach the grille over the baffle cover, making sure that all six magnets are secure.
-
Page 6: Amplifier Connections
Pro Tip: Pass the wire through the bottom hole of the binding post and tighten down on the wire. This allows the wire to lay flat in the wire channels and is less likely to cause a buzzing sound. Single speaker wiring with a 4 Ω load Supported SKUs: TS-PAS12-4, TS-PAS15-4, TS-PAS18-4... - Page 7 Dual speaker wiring in series with an 8 Ω load Supported SKUs: TS-PAS12-4, TS-PAS15-4, TS-PAS18-4...
- Page 8 Single DVC speaker wiring with a 2 Ω load (4 Ω load per voice coil) Supported SKU: TS-PAS18-DVC-4...
- Page 9 Single DVC speaker wiring to two amplifiers with a 4 Ω load per voice coil Supported SKU: TS-PAS18-DVC-4...
- Page 10 Single speaker wiring in series with an 8 Ω load each (4 Ω load per voice coil) Supported SKUs: TS-PAS18-DVC-4...
-
Page 11: Specifications
Min Impedance (in sealed box) Ohm 5.13 5.36 3.68 2 x 3.5 Frequency Response (-3dB) 19-300 22-300 23-300 23-300 (w/Triad tuning)* -6dB LF (w/ Triad tuning) Xmax 13.7 22.25 22.25 Sold as Each Each Each Each 32.75" x 24.25" x 38.75"... - Page 12 BakPak, Binary, Dragonfly, Episode, Luma, Mockupancy, Nearus, NEEO, Optiview, OvrC, Pakedge, Sense, Strong, Strong Evolve, Strong VersaBox, SunBriteDS, SunBriteTV, Triad, Truvision, Visualint, WattBox, Wirepath, and Wirepath ONE are also registered trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the property of their respective owners.
Need help?
Do you have a question about the TS-PAS12 and is the answer not in the manual?
Questions and answers