Subscribe to Our Youtube Channel
Related Manuals for RocketFish RF-HPL302
Summary of Contents for RocketFish RF-HPL302
- Page 1 Whole Home HD Extender RF-HPL302 User Guide Before using your new product, please read these instructions to prevent any damage.
-
Page 2: Table Of Contents
Legal notices..................18 One-Year Limited Warranty..............21 Introduction Congratulations on your purchase of a Rocketfish Whole Home HD Extender. This system delivers 1080p full HD video and audio content anywhere in your home, using your home’s power lines. Power line transmission results in great range and high performance video without wireless interference or WiFi range limitations. -
Page 3: Safety Information
RF-HPL302 Safety information CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. -
Page 4: Additional Safety Information
7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. -
Page 5: Features
RF-HPL302 • Read the Rating Labels on the bottom of the Transmitter and Receiver for power input and other safety information. Features Package contents • Transmitter • Receiver • AC power cords (2) • HDMI cables (2) • Dual IR emitter cable •... -
Page 6: Front Panel
Transmitter Front panel Item Description Source indicators Light to show which input source is selected. Sync indicator If this indicator is off, the HD Extender Transmitter and Receiver have not established a connection. When they are connected, the indicator will blink according to the quality of the connection: as the connection quality improves, the indicator will blink slower. -
Page 7: Back Panel
RF-HPL302 Back panel Item Description RESET button Press (with a pen tip or paperclip) to reset to factory default settings. HDMI INPUTS Plug the HDMI cable from the source HD audio/video devices into these jacks. HDMI 1 is the default. - Page 8 Receiver Front panel Item Description Source indicators Light to show which input source is selected. Sync indicator If this indicator is off, the HD Extender Transmitter and Receiver have not established a connection. When they are connected, the indicator will blink according to the quality of the connection: as the connection quality improves, the indicator will blink slower.
- Page 9 RF-HPL302 Back panel Item Description RESET button Press (with a pen tip or paperclip) to reset to factory default settings. HDMI OUT Plug the HDMI cable from an HD TV into this jack. SERVICE port Service port, do not use.
-
Page 10: Remote Control
Remote control Item Description Press to turn on power to the Transmitter or Receiver. Press (power) to switch to standby mode. Source 1 Press to select the SOURCE 1 input. Source 2 Press to select the SOURCE 2 input. -
Page 11: Set Up Your Hd Extender
RF-HPL302 Set up your HD Extender This unique technology allows you to connect a DVR, cable box, or other video device to another TV anywhere in your home! Connect the Transmitter to your video device(s) and TV, then connect the Receiver to another TV to extend your viewing environment. - Page 12 To set up your HD Extender: 1 Place your Transmitter near your DVR, cable box, or other video device. 2 Connect your video source devices' HDMI output to the Transmitter's HDMI IN 1 or HDMI IN 2 inputs. You do not have to connect video devices to both HDMI inputs.
- Page 13 RF-HPL302 5 Place your Receiver near your TV. 6 Connect the Receiver's HDMI OUT jack to your TV's HDMI IN jack. 7 Press the Source/Input button on your TV's remote to select the correct HDMI input. 8 Plug the Receiver into AC power.
- Page 14 Set up the IR emitter and IR receiver An IR receiver cable and an IR emitter cable are included, allowing you to control a video source, even when it's in another room. Just point your devices' remote control at the IR receiver instead of your video sources themselves.
-
Page 15: Use Your Hd Extender
RF-HPL302 1 Plug the IR emitter cable into the Transmitter. 2 The IR emitter cable has two separate IR emitters, one for each video source device you want to control. For each IR emitter, remove the protective cover from the tape on the emitter and stick the emitter near the IR sensors on your video sources. -
Page 16: Troubleshooting
Notes: The Receiver and Transmitter will automatically turn on and off based on the power state of the TVs connected to the Receiver and Transmitter. • When the TV connected to the Transmitter is turned on, the Transmitter automatically turns on. •... - Page 17 RF-HPL302 Problem Solution No picture on your TV or • Make sure that the connections are correct and secure between the Transmitter input and your HD device projector output. • Make sure that an HDMI input has been selected as the source on your TV or projector.
-
Page 18: Specifications
Specifications Video CODEC H.264 video encode and decode Video Resolution Support up to 1920 x 1080 @ 60p Digital audio Dual channel, Linear PCM, 44.1 KHz, 48KHz Power Line Link speed 500 Mbps SmartLink PLC technology Power Consumption Standby - 4.2 W On - 6.0 W Legal notices This device complies with Part 15 of the FCC Rules. -
Page 19: Open Source Software
For Open Source Software information, if you require additional information or you wish to receive the complete corresponding licensed source code, please call the Rocketfish support line at 1-800-620-2790. This source code is available for a period of three (3) years from the date of the distribution of this product... -
Page 21: One-Year Limited Warranty
One-Year Limited Warranty Rocketfish Products (“Rocketfish”) warrants to you, the original purchaser of this new RF-HPL302 (“Product”), that the Product shall be free of defects in the original manufacture of the material or workmanship for one (1) year from the purchase of the Product (“Warranty Period”). -
Page 22: What Does The Warranty Not Cover
• Damage due to incorrect operation or maintenance • Connection to an incorrect voltage supply • Attempted repair by anyone other than a facility authorized by Rocketfish to service the Product • Products sold as is or with all faults •... - Page 23 7601 Penn Avenue South, Richfield, Minnesota, U.S.A. 55423-3645 © 2014 Best Buy Enterprise Services, Inc. All rights reserved. ROCKETFISH is a trademark of Best Buy Enterprise Services, Inc. Registered in some countries. All other products and brand names are trademarks of...
- Page 24 Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richfield, MN 55423-3645 USA © 2014 BBY Solutions, Inc. All rights reserved. ROCKETFISH is a trademark of BBY Solutions, Inc. All other products and brand names are trademarks of their respective owners. V1 ENGLISH 14-0333...
Need help?
Do you have a question about the RF-HPL302 and is the answer not in the manual?
Questions and answers