Advertisement
How to Configure DS-TMC403-E(/WG)
1. Installation
Installation Standard
Choose a horizontal installation floor
Pre-embedded cables, the conduit should be 50 mm above the ground to prevent
water from entering the cable and causing a short circuit
When installing against a wall, at least 200mm of space should be reserved between
the back cover and the wall to facilitate wiring and other operations
When installing this device, the fuselage needs to be turned sideways to align with
the capture position;
(1) Capture Distance
The capture position is 3.5-5m away from the capture unit
2. Fixed Base
The camera needs to be fixed to the mounting surface with expansion screws.
(1) According to the general direction of the all-in-one chassis on the safety island,
punch 3 holes in the safety island, as shown in the figure below
(2) Use an impact drill to drill holes on the installation holes with a depth of about
Advertisement
Table of Contents
Related Manuals for HIKVISION DS-TMC403-E/WG
Summary of Contents for HIKVISION DS-TMC403-E/WG
- Page 1 How to Configure DS-TMC403-E(/WG) 1. Installation Installation Standard Choose a horizontal installation floor Pre-embedded cables, the conduit should be 50 mm above the ground to prevent water from entering the cable and causing a short circuit When installing against a wall, at least 200mm of space should be reserved between the back cover and the wall to facilitate wiring and other operations ...
-
Page 2: Cable Connection
120mm; for the 3 racetrack holes at the bottom (3) Insert the expansion bolts with a diameter of 12mm into the installation holes, and tighten the nuts to fix them. 3. Cable Connection This equipment is equipped with a special terminal block, and all wiring needs to be completed on the terminal block. - Page 3 (2) Gate control and gate signal wiring: Control gate: the corresponding 1A1B2A2B corresponding to the opening and closing of the gate The wiring of the remote control alarm signal of the gate: the output of the gate is opened in place (remote control alarm) and connected to the camera ALARM IN1, After the gate signal wiring is completed, you need to configure the relevant functions in the Device...
-
Page 4: Application Mode
Check the firmware version and make sure the Smart Module Status is Normal. 5. Application Mode (1) Trigger type I/O coil: trigger camera capture by external switch signal, coil or radar Video Detection: trigger camera capture through pure video ... -
Page 5: Angle Adjustment
and so on (4) Radar hybrid configuration and wiring Select IO1 for the radar mixed forward radar, connect IN1 and GND for the corresponding trigger radar, select IO2 for the backward radar, and connect IN2 and GND for the corresponding logic radar 6. - Page 7 7. Pixel adjustment (1) License plate recognition position and pixel points The trigger recognition range of the capture camera is 3.5-5 meters, and the best position is 4 meters (the distance between the trigger capture and the camera); the capture position of the capture camera is best at the lower 1/3 of the overall image;...
-
Page 9: Capture Parameters
8. Recognition Area The identification area must be drawn according to the actual scene of the scene, and it is forbidden to use the default area or doodle randomly. When taking pictures, the license plate and the front of the car must be inside the recognition area. - Page 10 (2) Supplement Light Control Constant Light by Brightness: the lower the brightness threshold, the easier the fill light is to light up. When the threshold is 0, the fill light is always on. Control Constant Light by Schedule: enable it according to actual needs, it is recommended to enable it by schedule (1) Vehicle Feature ...
-
Page 11: Image Parameters
10. Image Parameters (1) General parameters WDR: If the lights are too bright at night and the image is too explosive, the WDR can be turned on to suppress the lights according to the time. Note: Turning on WDR will cause the image noise to increase, so you don't need to turn it on when it's not necessary ... - Page 12 Enterances and Exits Control mode: The platform control corresponding to the opening signal is sent by the platform; the camera control is controlled by the camera according to the vehicle information management to determine the opening of the gate itself ...
- Page 14 12. How to setup camera to work with HTTP POST Go to Network Parameters > Data Connection > HTTP Listening Select Enable One if you are sending the data to one server only. Select Enable Two if you will also send the data to another server.
- Page 15 Set the preferred DNS Server to 1.1.1.1 or 8.8.8.8 Configure the Server IP, port and Absolute Path (URL) on camera webpage. The following is an example of configuring HTTP listening parameters for Zatpark: Select HTTP If it’s requested by Zatpark that the ANPR data be sent over HTTP. Select HTTPS If it’s requested by Zatpark that the ANPR data be sent over HTTPS.
-
Page 16: How To Send
like to use host name instead, please setup DNS server in advance. Add Port provided by ZatPark. Normally it is 80 Add Absolute Path provided by ZatPark.(Also known as URL. )： /xxxx/xxxx/xxxx ； Set Alarm Server Mode to ZatPark ... - Page 17 Click ‘Arming’, once there is a License plate is recognised, it will be displayed in the Picture List. HTTP server (like ZatPark) will also receive this ANPR reads. Or you can click the ‘Continuous Capture’ if there is no vehicle pass by, HTTP server (like ZatPark) will receive a Test Data with license plate number is UNKNOWN.
- Page 18 Option: It is possible to test whether the camera sends data by using TCP server emulation software. The following are the results of an ANPR Test using the TCP Server simulation tool to receive ANPR as an HTTP server. 2. How to reduce the data usage? You could reduce the data usage by lowering the Capture Resolution (e.g.
- Page 19 (2) You could lower the image quality (as explained in 2.How to reduce the data usage), just so each piece of information will take less bandwidth. If this still not resolve the problem, please contact Hikvision support team. Contact Please contact the following windows if you have any further questions or need any help.
Need help?
Do you have a question about the DS-TMC403-E/WG and is the answer not in the manual?
Questions and answers