Subscribe to Our Youtube Channel
Summary of Contents for Ecobee Smart Doorbell Camera
- Page 1 Smart Doorbell Camera • What’s in the box? • Wiring diagrams Replace with Smart Doorbell Camera asset...
- Page 2 Smart Doorbell Camera Backplate & Security Wedge ecobee Smart Doorbell Wire Extenders (x2) screw (pre-attached) Camera Long Screws (x2) Allen Key Wire Connectors (x5) Anchors – Brick only (x2) Short Screws (x4) Chime Adapter...
- Page 3 Smart Doorbell Camera 1/4” masonry bit (hard surfaces) Drill Needle-nose pliers Phillips Screw Driver 5/64” (soft surfaces)
-
Page 4: Turn Off Power
Smart Doorbell Camera 1. Locate Chime Box Easiest way to do this is by ringing the doorbell & following the sound. 2. Turn off Power Once you have located the chime box and confirm the doorbell is working, turn off the power by turning off the circuit breaker... - Page 5 Smart Doorbell Camera 3. Remove Chime Box Cover 4. Take a photo of the chime box: We know you are Pros at this, but we recommend taking photos the chime box. Make sure the wiring and labels are clearly visible.
- Page 6 Smart Doorbell Camera 7A: Disconnect the FRONT wire. 5A: Disconnect the TRANS wire. 9A: Connect the U-wires to the TRANS and FRONT terminals. The order and color of the wires do not matter. Attach one of the U- 6A: Connect the chime adapter’s black 8A: Connect the chime adapter’s red...
- Page 7 Smart Doorbell Camera This is the wiring setup for homes with one doorbell. Double-check the Chime Box Wiring Setup and confirm they are secure.
- Page 8 Smart Doorbell Camera 13B. Attach the Chime Adapter Find a spot for the chime adapter where it will not impact the sound of the doorbell. Use the adhesive on the back of the chime adapter to secure it. See examples below 14B: Put the cover back on &...
- Page 9 Smart Doorbell Camera 7B: Disconnect the Trans Wire: 5B: Disconnect the Rear Wire: 9B: Disconnect the Front Wire: 6B: Connect the chime adapter’s blue 8B: Connect the chime adapter’s blue 10B: Connect the chime adapter’s blue wire with the Rear wire...
- Page 10 Smart Doorbell Camera 11B: Connect the chime adapter’s red wire with the FRONT wire 12B: Connect the U-wires to the TRANS and FRONT terminals...
- Page 11 Smart Doorbell Camera This is the wiring setup for homes with more than one doorbell. Double-check the Chime Box Wiring Setup and confirm they are secure.
- Page 12 Smart Doorbell Camera 13B. Attach the Chime Adapter: Find a spot for the chime adapter where it will not impact the sound of the doorbell. Use the adhesive on the back of the chime adapter to secure it. See examples below 14B: Put the cover back on &...
- Page 13 Smart Doorbell Camera 1. Remove Old Doorbell 2. Disconnect and bend the wires...
- Page 14 Smart Doorbell Camera 3. Attach the wire extenders Twist the exposed portion of the wire extender and one of the wires from the wall. Align the tips of the wires and screw on a wire connector. Repeat with the second wire extender.
- Page 15 Smart Doorbell Camera 5. Align the wedge & mark the holes Gently pull the wires through the bottom hole. Make sure the smooth side is facing the wall.
- Page 16 Smart Doorbell Camera 6. Are you installing on a hard or soft surface? Drill the holes with a 5/64" bit Drill the holes with a 1/4” masonry bit & insert the anchors...
- Page 17 Smart Doorbell Camera 7. Attach the wedge Align the wedge, then gently pull the wires through the bottom hole. Screw the provided long screws into the wide slots. 8. Detach the backplate from the doorbell Using the provided Allen key, loosen the security screw on the bottom of the device until you can lift the backplate off.
- Page 18 Smart Doorbell Camera 9. Guide the wires through the backplate 10. Attach the backplate to the wedge Screw the provided short screws into the smaller holes.
- Page 19 Smart Doorbell Camera 11. Loosen the terminal screws Loosen the 2 terminal screws on the back of the doorbell. Do not remove the terminal screws. 12. Connect the U-wire to the terminal and tighten the screw Slide the U-wire under the terminal screw, with the U-wire pointing down.
- Page 20 Smart Doorbell Camera 13. Hang the doorbell on the backplate & secure the doorbell. Slide the U-wire under the terminal screw, with the U-wire pointing down. The order of the wires does not matter. Tighten the terminal screw. 14. Turn on the power for the doorbell.
- Page 21 Smart Doorbell Camera 15. Is the light loop on the front of the doorbell solid green? This may take a minute or two. If no, try these troubleshooting steps: 1. Turn off power to your system. 2. Make sure all the wires are connected correctly.
- Page 22 Smart Doorbell Camera 16. Ring the doorbell to test the sound Look at the possible outcomes below. If you can hear the in-home chime, you have successfully installed the ecobee Smart Doorbell Camera. If you cannot hear the in-home chime, press and hold the doorbell button until the light loop flashes green 3 times.
- Page 23 Smart Doorbell Camera Install the ecobee app on the Homeowners phone QR CODE QR CODE Android Login or Create an account.
Need help?
Do you have a question about the Smart Doorbell Camera and is the answer not in the manual?
Questions and answers