Advertisement
Quick Links
Installation Instructions
Sunnex Solo Spot Exam Light
Models: HM2006-38EXT, HM2005-37EXT, HM2017-44EXT
1.1 Applications
The Sunnex Solo Spot Series light was designed specifically for medical applications where a
focused cool light is required.
1. SoloSpot with direct
2. SoloSpot with wall
mount
mount
3. SoloSpot with
4. SoloSpot with
C-Clamp
trolley base
1.2 Cleaning and Disinfection
The lamp fixture can be cleaned as needed with a damp cloth and a mild detergent. For disinfection use a
soft cloth with a disinfectant solution such as isopropyl alcohol. NOTE! Do not introduce any fluids to the
inside of the lamp head as this could cause a fire hazard.
1
Sunnex Solo Spot Service & Installation Manual
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for SUNNEX Solo Spot HM2006-38EXT
- Page 1 Installation Instructions Sunnex Solo Spot Exam Light Models: HM2006-38EXT, HM2005-37EXT, HM2017-44EXT 1.1 Applications The Sunnex Solo Spot Series light was designed specifically for medical applications where a focused cool light is required. 1. SoloSpot with direct 2. SoloSpot with wall...
- Page 2 WEEE standard. 2.3 Transportation and Storage This light is packaged in card board and should be transported protected from moisture. The light should be stored in a dry environment and room temperature. Sunnex Solo Spot Service & Installation Manual...
- Page 3 4. Remove the halogen cold light bulb from its socket. 5. Replace the damaged halogen cold light reflector. Only Sunnex cold light reflector with part. no. 18562 must be used. NOTE! Make sure the cold light reflector is clean and without fingerprints.
- Page 4 4. Tighten the screw (7). Secure the legs in the housing by lining up the teeth on the clamp plate (5) with the holes in the legs. SoloSpot with direct mount Sunnex Solo Spot Service & Installation Manual...
- Page 5 2. SoloSpot with wall mount 3. SoloSpot with C-clamp Sunnex Solo Spot Service & Installation Manual...
-
Page 6: Hole Pattern
2. Be sure transformer plug is not plugged into power source at this time. 3. After down tube support is secured plug electrical connectors at the end of the down tube support and lamp arm together. HOLE PATTERN Sunnex Solo Spot Service & Installation Manual... - Page 7 Warranty extends only to the original buyer. If the Product is determined to be defective within the warranty period, Sunnex, at its option, will repair or replace the Product, at no charge or refund the then-current value of the Product.
- Page 8 Sunnex and displayed prominently on the outside packaging of any Product shipped to Sunnex. (c) Within ten (10) days of receipt of the RMA number, Customer must ship the Product to Sunnex at Customer’s expense (insuring the Product is recommended) in either its original packaging or packaging affording an equal degree of protection, to Sunnex Inc.
- Page 9 Product or the Extended Limited Warranty to become effective and apply to the Product. Customer must pay the appropriate Extended Limited Warranty fee and upon initial purchase, register each Product with Sunnex within thirty (30) days from the date of shipment to Customer by Sunnex, or a Sunnex authorized dealer or reseller.
- Page 10 The power frequency magnetic field should be measured In the intended installation location to assure that It is sufficiently low. NOTE U is the a.c. mains voltage prior to application of the test level. Sunnex Solo Spot Service & Installation Manual...
- Page 11 SoloSpot Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m. Sunnex Solo Spot Service & Installation Manual...
- Page 12 If it is inadvertently brought into patient areas. NOTE 4 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people. REV. 1 JULY 2008 Sunnex Solo Spot Service & Installation Manual...
Need help?
Do you have a question about the Solo Spot HM2006-38EXT and is the answer not in the manual?
Questions and answers