JMTek MBT200-M Instruction Manual

Microphone Bluetooth Speaker Instruction Manual
Please read the following carefully before using this device to ensure safe
and proper usage.
Important: Before using your wireless speaker with microphones for the
first time, fully charge it.
SPECIFICATIONS
Input (Type-C): 5V 2A at the back (for the main unit) or on the base (for
the main unit and microphones). Designed with pogo pin connectors and
mating pads for charging the main unit and microphones. Includes AUX
input, TF/USB card playback.
Output value in Watt 5W
Bluetooth version 5.3
Charging time 160 minutes
Total play time at 50% volume (hours) 6 hours
Pick up function No
Operating distance 10m.
Speaker driver 57mm.
S/N Ratio >65dB
Frequency range 200Hz-18KHz
Pairing name MBT200
Battery capacity speaker 2000mAh
Battery capacity microphones 1200mAh*2
1
MICROPHONE PANEL
1. To control power and various volume settings:
- Switch between music volume,
micro volume, and reverberation volume.
- Play or pause by double-clicking.
2. To increase volume or move to the next track.
3. To decrease volume or go to the previous track.
4. To control the microphone:
1.
2.
3.
4.
5
260 x 95mm 70g书写纸 双面印刷
�
Microphone Bluetooth Speaker Instruction Manual DEVICE LAYOUT
TOPPANEL
Please read the following carefully before using this device to ensure safe
and proper usage.
Important: Before using your wireless speaker with microphones for the
first time, fully charge it.
SPECIFICATIONS
Input (Type-C): 5V 2A at the back (for the main unit) or on the base (for
the main unit and microphones). Designed with pogo pin connectors and
mating pads for charging the main unit and microphones. Includes AUX
input, TF/USB card playback.
1.
Output value in Watt 5W
2.
Bluetooth version 5.3
Charging time 160 minutes
Total play time at 50% volume (hours) 6 hours
Pick up function No
Operating distance 10m.
Speaker driver 57mm.
S/N Ratio >65dB
Frequency range 200Hz-18KHz
Pairing name MBT200
2. Volume down or previous track
Battery capacity speaker 2000mAh
3. Play or pause
Battery capacity microphones 1200mAh*2
4. USB disk, TF card or Bluetooth; RGB lightcontrol
5. Volumeup or previous track
1
第1折痕
标准说明书
260mm
Ω
�
BACKPANEL
DEVICE LAYOUT
TOPPANEL
2. 3.
1.
1. 4.
2. 5.
BACKPANEL
3.
1. AUX IN
ff Connect an external audio device using a 3.5mm audio cable.
2. TF CARD
Insert a TF card to play.
3. USB DISK
Insert a USB flash drive to play.
2. Volume down or previous track
4. LED LIGHT
3. Play or pause
Displays the status of charging and microphone connection. fl
4. USB disk, TF card or Bluetooth; RGB lightcontrol - The red LED lights up when charging and goes out when fully charged.
5. Volumeup or previous track - The blue LED lights up when connected and flashes when disconnected.
5. TYPE C PORT
； Connect to a power supply to charge the main unit.
2
TF/USB CONNECTION
POWER ON
Insert a TF card or USB storage device containing playable audio content into
To power on the device and enter Bluetooth pairing mode, press and hold
the TF card slot or USB port of the speaker.
the power button for 3 seconds.
- The speaker will switch to the TF card or USB source automatically.
- Audio playback will begin automatically.
USING
MUSIC CONTROL
Press the "play" button once to pause or resume playback.
NOTES:
- Only one sound source can be played at a time. The priority order is
AUX CONNECTION
TF/USB /BLUETOOTH/AUX.
1. Attach an external audio device to the speaker using a 3.5 mm AUX cable
- Starting a source with higher priority will always interrupt a source with
(cable not included).
lower priority.
2. Once playback from any other source has been stopped, commence audio
- To start a source with lower priority, stop the source with higher priority
playback on the external device.
first.
MIXING SOUND WITH A MICROPHONE
BLUETOOTH CONNECTION: When utilizing a microphone, you have the ability to blend sound with an
audio source.
- You can use the speaker with your Bluetooth-enabled smartphone or
tablet.
NOTES:
- Choose "MBT200" on your Bluetooth device to connect.
- Prior to connecting or disconnecting the microphone, ensure that the
microphone volume is set to the minimum level.
- Once successfully connected, you can stream audio from your Bluetooth
device to this speaker.
- To terminate the Bluetooth-enabled device:
CONNECTING THE MICROPHONE
The wireless microphone is pre-paired with the speaker by default at the
factory.
• Disable Bluetooth on your device.
Turn on the speaker and then the supplied wireless microphones one by one.
- To reconnect the Bluetooth-enabled device:
You will hear a prompt tone once the wireless connection is successfully
• When you turn on this speaker next time, it tries to reconnect the last
set up.
connected device automatically.
SING THROUGH THE MICROPHONE
• If not, manually select "MBT200" on your Bluetooth device
To adjust the volume of the audio source, press the "+" or "-" button once to
to connect.
increase or decrease it.
6 7
说明书折法：
Ω
BACKPANEL
4.
2. 3.
1.
4.
5.
BACKPANEL
3.
1. AUX IN
ff Connect an external audio device using a 3.5mm audio cable.
2. TF CARD
Insert a TF card to play.
3. USB DISK
Insert a USB flash drive to play.
4. LED LIGHT
Displays the status of charging and microphone connection. fl
- The red LED lights up when charging and goes out when fully charged.
- The blue LED lights up when connected and flashes when disconnected.
�
5. TYPE C PORT
；
Connect to a power supply to charge the main unit.
ED fl
2 3
第2折痕
MBT200-SMS-JMT001
MBT200
POGO PINS AND MATING PADS
�
4.
5.
Please place the main unit and microphones into the base. They will be
charged when needed.
NOTE:
Ensure that the microphones slide down the slot into the base connecting
the pogo pins to the mating pads.
�
ED fl
3 4
LIGHT EFFECT
You can switch between seven performance styles by double-clicking "M".
RECHARGING YOUR MAIN UNIT AND MICROPHONES:
To recharge your main unit and microphones, place them into the base
and use the provided USB cable to connect the Type-C port on the base
to a USB wall charging adapter. During the recharge process, the red LEDs
will be illuminated. Once the main unit and microphones are fully charged,
connecting the supplied USB cable to the Type-C port on the back of the
main unit to a USB wall charging adapter.
NOTICE
1. Keep the product dry; do not place the product in damp places.
2. Keep out of direct sunlight and high temperatures. High temperatures
may result in damage.
3. Keep out of cold temperatures; this will help avoid internal damage.
4. Improper usage can lead to explosions or the risk of chemical burns.
When damaged, batteries can cause chemical burns upon contact
with human skin.
5. Do not disassemble the product.
6. Avoid dropping the product.
7. Do not continue to charge the product over 10 hours.
8. When charging use the Type-C charging cable that came with the
product.
9. Only charge with devices rated and marked with 5V to avoid damage
to the speaker.
10. Battery life and number of charge cycles varies by use and settings.
11. Keep away from small children. This is not a toy.
12. To maintain good battery health, the item should be recharged every
6 months. The battery will lose capacity when stored without
charging.
8
POGO PINS AND MATING PADS
�
5.
Please place the main unit and microphones into the base. They will be
charged when needed.
NOTE:
Ensure that the microphones slide down the slot into the base connecting
the pogo pins to the mating pads.
4
第3折痕
第1版
240513
正面
（Front）
背面
（Back）
POGO PINS AND MATING PADS
Microphone Bluetooth Speaker Instruction Manual
Please read the following carefully before using this device to ensure safe
and proper usage.
Important: Before using your wireless speaker with microphones for the
first time, fully charge it.
SPECIFICATIONS
Input (Type-C): 5V 2A at the back (for the main unit) or on the base (for
the main unit and microphones). Designed with pogo pin connectors and
mating pads for charging the main unit and microphones. Includes AUX
input, TF/USB card playback.
Output value in Watt 5W
Bluetooth version 5.3
Charging time 160 minutes
Total play time at 50% volume (hours) 6 hours
Pick up function No
Operating distance 10m.
Speaker driver 57mm.
S/N Ratio >65dB
Please place the main unit and microphones into the base. They will be
Frequency range 200Hz-18KHz
charged when needed.
Pairing name MBT200
NOTE:
Battery capacity speaker 2000mAh
Ensure that the microphones slide down the slot into the base connecting
Battery capacity microphones 1200mAh*2 the pogo pins to the mating pads.
1
折后正面
折后尺寸：65 x 95mm
Steven
�
4
折后背面