Summary of Contents for SINBON WSM-A0 Series
- Page 1 User Manual Model Name: WSM‐A0x Wi SUN Module Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com...
- Page 2 4.6 Suggested circuit 4.7 Module PCB Dimension 4.8 Environmental Recommended Land Pattern pages 11 Odering and Marking Information pages 11 Product Marking pages 12 Packing Information pages 12 Statement information pages 13~14 Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com...
- Page 3 Revision Index Date Status / Comments Aug/12/2021 Release May/29/2023 Shielding & WSM‐A01 Firmware update to version: V1.0.0.0 Aug/22/2023 Add Statement information Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com...
- Page 4 Advanced Metering Infrastructure (AMI): Wi‐SUN is well‐suited for AMI deployments, where it enables two‐way communication between utility companies and smart meters. It facilitates automated meter reading, remote disconnect/reconnect, and real‐time data collection for billing and load management. Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com...
-
Page 5: Specification
‐109 dBm at 50 kbps GFSK (Typ.)(100 kbps,BER<0.1%) Frequency deviation ±20ppm or less Power Supply VDD=2.7~3.6V Current 50~145 mA(Typ.)[Transmission] consumption 30 mA(Typ.)[Reception] (VDD=3.3V) 7mA(Typ.)[Sleep state] (Data rate=100 kbps) Host interface UART(115,200 bps) Certification FCC/CE/NCC Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com... - Page 6 1K Ohm BOOT Setting RESETn 0 : Flash Boot (Default) USB to UART Bridge 0.1uF 1 : iROM Boot Status Indication (Option) UART1 Setting BOOT=0 : Console (Default) BOOT=1 : Programming Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com...
-
Page 7: Module Pin Out
Default: General purpose IO, IOA3. IOA3 Function 1: Second pulse output (RTCPLL divider output) Function 2: EINT3 Default: General purpose IO, IOA9. IOA9 Function 1: ADC channel 1 input Function 2: EINT9 Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com... - Page 8 Function 4: Key scan output 0 Function 5: FSPI SRAM CSN TXO_M_OUT EXT PA, RF single out TXO_M_IN EXT PA, RF single in GPIO5 GPIO w ePA Power Control RF in /out Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com...
- Page 9 Suggested circuit Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com...
- Page 10 Operating Humidity Range 20 to 90% RH (without condensation or freezing) ‐40~105℃ Storage Temperature Range 20 to 95% RH Storage Operating (Sharp temperature change,without condensation or Humidity Range freezing not allowed) Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com...
-
Page 11: Recommended Land Pattern
5 Recommended Land Pattern 6 Odering and Marking Information Part Number Description Note WSM‐A01 IEEE 802.15.4g, Wi‐SUN Stamp Module , LPWAN, U.FLx1 (915Mhz) A9314288‐001 WSM‐A02 IEEE 802.15.4g, Wi‐SUN Stamp Module , LPWAN, U.FLx1 (868Mhz) Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com... - Page 12 Product Marking 8 Packing Information Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com...
- Page 13 XXXXX‐XXXXX”. The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co‐located or operating in conjunction with any other antenna or transmitter. Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com...
- Page 14 NCC 警語 「取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大 功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經 發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管 理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性 電機設備之干擾。」 本模組於取得認證後將依規定於模組本體標示審驗合格標籤，並要求最終產品平台廠商 (OEM Integrator)於最終產品平台(End Product)上標示” 本產品內含射頻模組， 其 NCC 型式認證號碼為: CCXXxxYYyyyZzW Aug/22/2023 Version 1.2 / Status: Released VISIT US: www.sinbon.com...
Need help?
Do you have a question about the WSM-A0 Series and is the answer not in the manual?
Questions and answers