Sony NSD-M1000 Operating Instructions

F:\Works\819712U_20230411_Lunx\H057100111\H057100111NSDM1000U\EN1U.indd
DTP data saved: 2023/03/31 13:29
PDF file created: 2023/04/11 06:27
Wireless LAN Extender
Operating Instructions
NSD-M1000
© 2023 Sony Network
Communications Inc.
Printed in China
Owner's Record
The model and serial numbers are located on the bottom of the unit.
Record the serial number in the space provided below. Refer to these
numbers whenever you call upon your Sony dealer regarding this product.
Model No. NSD-M1000
Serial No.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Country Code selection feature to be disabled for products marketed to the US/CANADA
Operation of this device is restricted to indoor use only
Checking the supplied items
Check that all the following items are included in the package.
If there is any missing item, consult with your service provider.
• NSD-M1000 main unit • AC adaptor
• Operating Instructions (this
document)
Identifying parts
H-057-100-11(1)



 WPS button
 Status indicator
 Ventilation holes
Status indicator
Color and state of indicator
Flashes in green and red
Lights up in green
Lights up in red
Flashes in green
Flashes in orange
Flashes in red
Lights off
Setup 1: Setting up on the ONU
Enable the Wi-Fi mesh function of the ONU (ONU Integrated High-speed Router) in
the following steps.
1
Connect your smartphone or computer to the ONU via Wi-Fi.
2
After the connection is established, access the following URL on the
browser of the smartphone or computer.
http://192.168.1.1
3
Enter the user name and the password to log in.
Find the password on the bottom exterior of the ONU.
SSID(5G) : xxx-xxxxx-xxx-x
SSID(2.4G) : xxx-xxxxx-xxx-x
Key (WPA) : xxxxxxx
4
After login, select [Detail Setting] - [Wi-Fi Mesh Function]




 LAN terminal
 RESET button
 DC IN jack
 Product label
Unit status
Wireless LAN is not set up (default settings).
Connected in EasyMesh mode
Start-up failed/software update failed
Pairing with the wireless LAN router (base
unit) is in progress.
Being started up/being reset/software being
updated
No connection with the wireless LAN router
(base unit)/an invalid software update file
received
Power off
WEB-GUI: xxxxxxx
5
Set [Enabel Wi-Fi Mesh] to ON and select [Apply].
It may take about 30 seconds until the setting is completed.
Setup 2: Pairing
Pair the ONU and this unit (Wireless LAN Extender). There are two pairing methods;
pairing by the WPS button and pairing by connecting the LAN cable.
Pairing by the WPS button
1
Place this unit near the ONU.
2
Connect the supplied AC adaptor to this unit.
Status indicator
The status indicator on the rear of this unit flashes in orange, and then it flashes
in green and red alternately.
3
Press and hold the WPS button on the rear of the ONU for 5 seconds.
Status indicator
The status indicator on the rear of this unit changes to flashing in green.
4
Press and hold the WPS button on the top of this unit for 5 seconds.
The setting is completed when the status indicator on the rear of this unit lights
up in green.
If the status indicator does not change to light up in green, disconnect the AC
adaptor and repeat from step 2.
Continued on back page
NSD-M1000
H-057-100-11(1)