Introduction Thank you for choosing the PCD F40 fixed wireless phone. This phone is designed for use with UMTS 850/900/1900/2100 MHz, 4G B2/3/4/5/7/12/13/17/28/41/66 networks. For operation requires a valid SIM card from your network operator. Please consult your network operator for more information.
Precautions for use Operating Environment Your phone PCD F40 is an RF transmitter, so please turn off your terminal or disable the radio functions in the following situations: ●● When you are on an airplane. ●● When you are in the vicinity of flammable atmospheres and is indicated by the entity responsible for risk management.
Emergency calls Like any mobile phone, this phone works with radio signals that can not guarantee connection in all conditions. Therefore, you should never rely solely on a mobile phone for essential communications like medical emergencies. To make or receive calls, the phone must be switched on and in a service area with adequate signal strength.
Battery use ●● Never use any charger or battery if damaged. Use the battery correctly. ●● Do not short-circuit the battery, as this may damage the battery or cause a fire. ●● Do not subject the battery to high temperatures or fire as it may explode. ●●...
Installation Follow the steps below to install the SIM card and the different accessories of your phone PCD F40: 1. Disconnect the power adapter and remove the cover of the battery compartment on the bottom of the device to install the SIM card and the micro-SD memory card.
5. Connect the short end of the curly cord to the connector on the handset, as shown in the illustration. 6. Connect the cable from the power supply to the connector on the front of the phone and then plug the power supply into a household AC power outlet. The battery level will be displayed on the screen showing the status of the charging process.
Charging a completely discharged battery can comprise from 2 to 3 hours. Fully charge the battery before first use of the device. Note: Always make sure your device is turned off before removing your SIM card. This will prevent data loss and damage to the SIM card. Do not place the SIM card near surfaces or electromagnetic environments and avoid touching the metal connectors.
Page 12
[OK]ok key Confirmed key [Audio] Audio profiles key Select the corresponding audio profiles [FM] FM key Enter FM function [Redial] Redial key In standby mode, press to redial the last number of the call log.
Main menu Once you turn on the device and complete the setup process, the main menu will be displayed on the screen. Applications Menu Press on the key [Menu] on the left side of the main menu to access the applications menu.
Make a Call There are several ways to perform callings with your terminal PCD F40: Calling using the alphanumeric keypad 1. In standby mode, enter the phone number using the alphanumeric keypad and press [ ] button or pick up handset to call.
the call. 2. To reject an incoming call, press the [Cancel ] button. Adjusting the handset volume During an active call, press the [▲ ] [▼ ] buttons to decrease or increase respectively the volume of your headset or handsfree. Features Bluetooth connection ·...
turn off, please check the "on" then press the [OK] key again. Troubleshooting The phone can not be turned on ●● Be sure to hold down the [ ] button for more than 3 seconds. ●● Make sure the battery is properly connected to your phone. ●●...
Page 17
Your correspondent can not call you ●● Make sure the phone is turned on and connected to a network. ●● Make sure the SIM card is not locked. ●● Check that the SIM card is within network coverage. ●● Check that you have not set an incoming call barring. Your correspondent can not hear you ●●...
Specific Absorption Rate (SAR) information: This PCD, LLC meets the government's requirements for exposure to radio waves. The and thorough evaluation of scientific studies.The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue.
Regulations This product bears the symbol of selective treatment of electrical and electronic waste (WEEE). This means that this product must be treated according to the European Directive 2002/96 / EC when it is recycled or dismantled to minimize its impact on the environment. For more information, please consult your local or regional authorities.Electronic products not included in the selective treatment process.Are potentially hazardous to the environment and human health, due to the to the presence of dangerous...
Need help?
Do you have a question about the F40 and is the answer not in the manual?
Questions and answers