Advertisement
Quick Links
SETUP & OPERATION MANUAL
Convert almost any drill press into a
mortiser in minutes!
Supplied with a convenient storage case –
kit contains:
Mounting hardware
Cast-iron Chisel Holder
Guide fence with workipiece hold-
down
4 of the most commonly used morti-
sing chisel and bit sets with 5/8" bit
shank x 1/4", 5/16", 3/8" & 1/2"
Adapter hardware including 6 bush-
ings (4 two-piece & 2 split style) to fit
most drill presses with 52, 55, 58, 60, 65 &
66 mm quills
MORTISING ATTACHMENT KIT
MODEL
# 70-905
REVISION 1 - August 11/08
© Copyright General International 08/2008
https://manual-hub.com/
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for General International 70-905
Summary of Contents for General International 70-905
- Page 1 Adapter hardware including 6 bush- ings (4 two-piece & 2 split style) to fit most drill presses with 52, 55, 58, 60, 65 & 66 mm quills MODEL # 70-905 REVISION 1 - August 11/08 © Copyright General International 08/2008 https://manual-hub.com/...
- Page 2 THANK YOU for choosing this General ® International model 70-905 Mortising Attachment Kit. This Mortising Attachment Kit has been carefully tested and inspected before shipment and if properly used and maintained, will provide you with years of reliable service. To ensure optimum performance and trouble-free operation, and to get the most from your investment, please take the time to read this manual before assembling, installing and ope- rating the unit.
- Page 3 ® ® GENERAL & GENERAL INTERNATIONAL WARRANTY All component parts of General®, General® International and Excalibur by General International ® products are carefully inspected during all stages of production and each unit is thoroughly inspected upon completion of assembly. Limited Lifetime Warranty Because of our commitment to quality and customer satisfaction, General®...
-
Page 4: Rules For Safe Operation
RULES FOR SAFE OPERATION To help ensure safe operation, please take a moment to learn the machine’s applications and limitations, as well as poten- tial hazards. General® International disclaims any real or implied warranty and holds itself harmless for any injury that may result from improper use of its equipment. - Page 5 Carefully unpack and remove the mortising attachment kit and its components from the box and check for dam- aged or missing items as per the list of contents below. NOTE: Please report any damaged or missing items to your General International distributor immediately. LIST OF CONTENTS CHISEL HOLDER .............1...
- Page 6 ASSEMBLY INSTRUCTIONS ASSEMBLE THE CHISEL HOLDER 1. Thread one of the knobs into the chisel holder 2. Slip the sprocket washer onto the T-slot bolt as shown then insert the T-slot bolt through the holder and secure in place with the locking lever as shown FIT THE CHISEL HOLDER TO THE DRILL PRESS 1.
- Page 7 6. Remove the alignment pin from the chuck. 5. Tighten the knob to hold the chisel holder in place on the alignment pin, then secure the chisel holder using the locking lever Note: Do not overtighten the locking lever – The gap does not need to be closed ASSEMBLE THE FENCE AND SECURE IT TO THE DRILL PRESS TABLE UNDERSIDE VIEW...
- Page 8 INSTALL A CHISEL AND BIT SET CHISEL AND BIT TIP ARE VERY SHARP . TO AVOID PERSONAL INJURY PUT THE PLASTIC CAP BACK ON THE CHISEL AND BIT SET BEFORE HANDLING OR INSTALLING IT ON THE DRILL PRESS. 1/2” 3/8” 5/16”...
-
Page 9: Parts Diagram
PARTS DIAGRAM *70905-22 CHISEL & BIT SET 70-910 = 1/4” 70-920 = 5/16” 70-930 = 3/8” 70-940 = 1/2” PARTS LIST 70-905 PART NO. REF. N0. DESCRIPTION SPÉCIFICATION 70905-01 BUSHING (TWO PIECE) 58 MM 70905-02 BUSHING (TWO PIECE) 52 MM... - Page 10 MODEL 70-905 8360 Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Tel.: (514) 326-1161 Fax: (514) 326-5565 - Fax: (514) 326-5555 - Parts & Service / Order Desk orderdesk@general.ca www.general.ca IMPORTANT When ordering replacement parts, always give the model number, serial number of the machine and part number.
Need help?
Do you have a question about the 70-905 and is the answer not in the manual?
Questions and answers