DG Electronics C_ratio,n. Ur_ut:_-,grized m_ificatbn could void tj,'_euser's autl_rib# to operate this prodS. The res_nsible pa@_' for this device compliance Zenith Electronics Corporation 1-201416-2000 Marked and districted in the Unit_ States by LG, Electronics U.S,A,, Inc. 1000 Sylvan Avenue,...
Safety Instructions ions WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Apparat_ To Rain Or Moisture. Apparatus s_ll not be exp_ed to dripping or splashing and no _jects filled with liquids, such as vases, shall _i pla_ on the apparatus.
Page 4
Safety, Instructions Instructions continued -..,, 12. Use only w_h a _rt, stand, tri_, bracket, or Refer a_l servicing to qualified servia per- table specified by the man_acturer, or _1_ sonnel. Servicing required when with the apparatus. When a cart i-sused, use apparatus has been damaged in any way,...
introduction Z15LCD1 Menu VO,L INPUT Menu INPUT Power/Standby Indicator G_ows red in Standby mode, Glows green when the TV is turned on Remote Control Sensor...
Introduction Functions When using the remote control, aim it at the remote control sensor on the TV, POWER: Power On/Off_ MUTE: Swithes on or off. 0~9: Number buttons 100:Number button:choose DISPLAY: Press this two ,three digital channel entry button display Channel, CH: Press4, or "_f to adjust channel,...
Installation i. Place the set with its front facing dowrnward on a soft cloth. 2. Assemble the stand into the set in the _rrect direction. Make sure you push it until you hear it "click". 3. Once assembled take the set up carefully and face the front side, Lock 3pcs.
Page 11
Installation Eq ui pm e nt C o n ne ct io ns - For optimum picture qualib,_, adjust antenna dir_tion. Connecting to an Inside Antenna _tup i i i Antenna Apa_ment Buildings Wall Conn_tion Jack Antenna Jack - if you have a 75_2 round cable, insert the bronze wire and then tighten the connection nut.
Insta Hation External Equipment Connections Continued - In Vid_ mode, TV automatically reverts to TV mode if the INPUT buttons are pressed. Connection Set VCR switch to 3 or 4 and then tune re to the same channel number, Typical Connection Antennas 1.
Instailation Connectio, ns Connect the audio/video output jacks on the external #JV equipment to the corresponding input jacks on the W. When connecting W to external AfV _uipment, match the jack colors (Vid_ = yellow, Audio Left = white, and Audio Right = red). Viewing Setup 1.
Ins_llation - To watch digitally broadcast programs, purchase and con- nect a digital set-top box. Connections DTV Receiver (Set-top Box) Connect the digital set-top box video outputs to the COM- PONENT (Y, Ps, PR) jacks and connect the digital set-top box audio outputs to the AUDIO jacks.
Page 15
Inst_ llatjon After setup, be sure to select PC source on TV. Connections i. Set the monitor output _lution on the PC before co.nnecting to the TV. 2. Connect the TV to the PC with me PC cable. 3. Connect the piC audio outputto the TV's PC SOUND input: Viewing...
Operation Press the MENU button to display each menu Use V,_II_ to select a menu item, Use 4, I_ to enter a submenu or enab[etdisaMe the function Press the MENU button to exit the menu. Press the MENU button to enter the main OSD (On Screen Display).
Operation Sound Menu Options The range of adjusting volume, bass : -05-+05,, treble : -05~+05. The range of adjusting Balance is; L40~R40; when adjusting from 0 to L40, the sound from the left track fades until silence; when adjusting from 0 to R40, the sound from the right track fades unti_ silence, AVL: you can set it "ON"...
Operation Picture Menu Options When the input source is in PC mode(Only for Z15LCD1) , you can select Brightness, Contrast, Position, Video noise, Sharpness, info,, Color Temp., Red, Green, Blue and Reset to default; shown the figure below: Brightness and Contrast: The range can be adjusted from 0-100.
Operation When the input source is in Component mode, you can select Brightness, Contrast, Video noise ,Co,or, Sharpness, Tint, Temperature and Reset to default respectively; shown in the figure below: Brightness and Contrast: The range can be adjusted from 0-100; use Brightness and Contrast options to adjust the brightness...
Operation (1). Only when the CNd Lock is ON and the Channelock will be enabled; when the Child Lock Setup is OFF, and the Channelock is disabled. (2)_ Lock code: VOhip password be set up when the code is locked, Enter the 4-digit password which you choose! The factory default pass_rd...
Operation MPAA Rating: Select the movie ratings from low to high (ale_) - & PG, PG=13, R, NC-17, X and Off. TV PG Rating: Shown in the figure below: The empty box refers to unlocked; the solid box refers to locked. Reset to default: Reset to the factory default value.
Operation Closed Captions Closed captioning is a process which converts the audio poAion of a television program into written words which then appear as subtitles on the television screen. Closed captions allow viewers to read the dia- logue and narrat:ion of television programs.
Maintenance & Product Specifications Ma inte na nce Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the. power off and unplug the power cord before you begin any 1.
Troubleshooting Checklist Troubleshooting • Check to see if there is any object between the product and the remote control causing obstruction. 'The mm_e control ° Are bakeries installed with correct _larity (+ to +, - to -)? dOesn't _ ° Correct remote operating mode set: TV, VCR etc.? •...
Page 25
Troubleshooting Check°list • Pre_ the VOL (or 'Volume) button. Picture OK & • Sound muted? Press MUTE button. No sound • Try another channel. The problem may be with the broadcast. • Are the audio cables installed properly? No output from •...
Page 28
• Repaired or replaced products are war- unit to Zenith for replacement ranted for the remaining potion of the Shipping charges both ways w[l_ be paid by Zenith during original warranty period.