Summary of Contents for Aclara Y84110-221
- Page 1 Edge Gateway Installation and Con guration Technical Manual Y21057-TUM Revision C www.Aclara.com...
- Page 3 Disclaimer The information in this document is subject to change without notice and should not be construed as a commitment by Aclara. Aclara assumes no responsibility for any errors that may appear in this document. No responsibility is assumed for the use or reliability of software on equipment that is not supplied by Aclara.
-
Page 5: Table Of Contents
Contents of Schweitzer SEL-351 Install Kit (Aclara PN 109-SEL351R) ......11 Contents of Schweitzer SEL-651 Install Kit (Aclara PN 109-SEL651R)..12 Installer Kit . - Page 6 Table of Contents A c l a r a E d g e G a t e w a y I n s t a l l a t i o n a n d C o n f i g u r a t i o n...
-
Page 7: Chapter 1: Warnings, Cautions, And Notes
Chapter 1 • Warnings, Cautions, and Notes CHAPTER ARNINGS AUTIONS OTES Always consult and adhere to all local and national safety codes, regulations, and standards.WARNING, CAUTION and Note statements are used throughout this manual to emphasize important and critical information to help you ensure safety and prevent product damage.These statements are defined below. -
Page 8: Supplier's Declaration Of Conformity
• Increase the separation between the equipment and receiver. • Connect the equipment to an outlet circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician (Aclara) for help. FCC ID: LLB2021006 IC:4546A-2021006 The antenna must not have a gain greater than: •... -
Page 9: Déclaration De Conformité Du Fournisseur
• Augmenter la distance séparant l'équipement du récepteur. • Brancher l'appareil dans une prise sur un circuit électrique différent de celui sur lequel le récepteur est branché. • Consultez le revendeur ou un technicien radio/TV expérimenté (Aclara) pour obtenir de l'aide. FCC ID: LLB2021006 IC:4546A-2021006 L'antenne ne doit pas avoir un gain supérieur à:... -
Page 10: Fcc/Ic Exposure Statement
FCC/IC Exposure Statement FCC/IC Exposure Statement Aclara Technologies LLC low power RF devices and their antennas must be fixed-mounted on indoor or outdoor permanent structure(s) providing a separation distance of at least 1 meter (about 3 feet) from all persons during normal operation. -
Page 11: Field Calibration Procedure
Procédure de calibration sur place Les appareils RF à faible puissance Aclara Technologies LLC ont été soumis à des tests étendus et multi-tâches et à des procédures de calibration complexes en usine. - Page 12 Procédure de calibration sur place A c l a r a E d g e G a t e w a y I n s t a l l a t i o n a n d C o n f i g u r a t i o n...
-
Page 13: Chapter 2: Product Specifications
CHAPTER RODUCT PECIFICATIONS The following table summarizes the specifications of Aclara’s Edge Gateway device. External enclosure NEMA 2 anodized aluminum, IPO2 Dimensions (LxWxD) 5.77” x 4.27” x 1.87” (146.6mm x 108.5mm x 47.5mm) Weight 1.1 lbs. (0.50 kg) Operating frequency 450MHz–470MHz, 901MHz–902MHz,... - Page 14 A c l a r a E d g e G a t e w a y I n s t a l l a t i o n a n d C o n f i g u r a t i o n...
-
Page 15: Chapter 3: Installation And Configuration
NSTALLATION AND ONFIGURATION This section of the document describes the contents of the Aclara Edge Gateway within the box when it arrives and how to configure the Edge Gateway device to connect with external controllers. This section describes how to install the Edge... -
Page 16: Contents Of Beckwith Install Kit (Pn 109-Becm6280A)
• Lightning Arrestor (Aclara PN 0015-0064) Contents of Beckwith Install Kit (PN 109-BECM6280A) • Shielded Ethernet Cable (Aclara PN 070-1800) • Power Cable (Aclara PN 070-2000C) • Earth Ground Cable (Aclara PN 070-3000C) A c l a r a E d g e G a t e w a y I n s t a l l a t i o n a n d C o n f i g u r a t i o n... -
Page 17: Contents Of Schweitzer Sel-351 Install Kit (Aclara Pn 109-Sel351R)
(Aclara PN 070-3000S) Earth Ground Cable Not included in the Aclara supplied kit, and to be ordered separately from Schweitzer: • Schweitzer serial port cable (Schweitzer PN SEL-C234A) or equivalent for serial port communications. • Schweitzer serial converter (Schweitzer PN SEL-2890) and associated serial cable for proper communications. -
Page 18: Contents Of Schweitzer Sel-651 Install Kit (Aclara Pn 109-Sel651R)
• Power Cable (Aclara PN 070-2000R) • Earth Ground Cable (Aclara PN 070-3000R) • Lightning Arrestor Adapter Plate (Aclara PN 056-0130) Not included in the Aclara supplied kit and to be ordered separately from Schweitzer: Schweitzer Accessory Shelf (Schweitzer PN 9250567) for mounting into the SEL-651 unit. -
Page 19: Installer Kit
Chapter 3 • Installation and Configuration Installer Kit • USB Type A to Type A Cable (Aclara PN 070-1703) Installation of Edge Gateway into Beckwith Capacitor Bank Controller The Edge Gateway device mounts directly onto the M-6280A or M-6283A Beckwith Capacitor Bank Controller utilizing the Utilinet mounting holes and the four provided mounting bolts. -
Page 20: Installation Of Edge Gateway Into Schweitzer Sel-351 Recloser Controller
Installation of Edge Gateway into Schweitzer SEL-351 Recloser Controller Create the antenna/lightning arrestor mounting hole as desired. Aclara recommends a location at the bottom of the enclosure. The preferred hole type is a 5/8” diameter “D” or “Double D” shaped hole. It is not recommended to punch these holes into the polycarbonate case. - Page 21 Chapter 3 • Installation and Configuration Mount the Edge Gateway device to the DIN Rail in the enclosure with the RF connector facing downwards. Orienting the Edge Gateway Device to the DIN Rail Mounting Plate Attach the ground cable to the lightning arrestor. Using the lightning arrestor adapter plate (PN 056-0130), mount the lightning arrestor (PN 0015-0064) to the bottom of the recloser controller enclosure at the desired location.
-
Page 22: Installation Of Edge Gateway Into Schweitzer Sel-651 Recloser Controller
SEL-351 that is configured for DNP3. Alternatively attach the provided shielded Ethernet cable to a properly configured and installed SEL-2890 Ethernet transceiver (not provided by Aclara). Connect the provided power cable to the Edge Gateway device using the 2.1 mm connector. -
Page 23: Recommended Scada Settings
• Intelligent Electronic Device (IED) or Remote Port number should always be 20000 for all IEDs • The SCADA or Local Port number should be unique for each IED. Aclara recommends starting with 20001, since the SCADA master is Port 20000, and use the DNP3 Node number as part of the port number. -
Page 24: Edge Gateway Configuration
• Keep alive time (Link Status) should be no faster than 60 seconds. • Response timeouts should be no shorter than 5 seconds. • Aclara recommends the use of unsolicited data, so changes to the IED can be reported in a timely fashion. This allows the Scans and Integrity Polls to be as infrequent as possible. - Page 25 Chapter 3 • Installation and Configuration Login using the Username and Password provided by Aclara to view the main screen. The default password for Username “Admin” is “HubbellAclara”. The default OTES password for Username “User” is “user”. To secure the Edge Gateway user...
-
Page 26: Troubleshooting
Troubleshooting Click on the button. New Configuration Enter a name for the configuration and enter all the information required for your specific setup. The information required is determined by the type of interface to the OTES Intelligent End Device (IED) (Serial or Ethernet). IP address is for the Edge Gateway device, not the connected IED. -
Page 27: Chapter 4: Support
Aclara University's Online Learning Center (OLC) and learning library, track your orders, join communities and groups, join in discussions with other Aclara customers and Aclara personnel, and much more. If you do not have access to Aclara Connect, email AclaraSupport@Hubbell.com request access. - Page 28 Returning Product A c l a r a E d g e G a t e w a y I n s t a l l a t i o n a n d C o n f i g u r a t i o n...
Need help?
Do you have a question about the Y84110-221 and is the answer not in the manual?
Questions and answers