Huawei FusionCharge DS720-720LEUA1 Quick Manual

FusionCharge
DC Charging Power Cabinet
Quick Guide
Product Model: DS720-720LEUA1
Product Number: 600-720H2F10M1
Document version: draft B
Document number: 31500JJC
Release date: 2023-10-27
Copyright © Huawei Digital Power Technologies Co., Ltd. 2023. All rights reserved.
Before installing the equipment, read the user manual carefully to get familiar with product
information and safety precautions. The product warranty does not cover equipment
damage caused by failure to follow the storage, transportation, installation, and usage
guidelines specified in this document and the user manual. You can scan the QR code on the
right to view the user manual and safety precautions.
The information in this document is subject to change without notice. Every effort has been made
in the preparation of this document to ensure accuracy of the contents, but all statements,
information, and recommendations in this document do not constitute a warranty of any kind,
express or implied.
The Danger, Warning, Caution, and Notice statements described in this document do not cover all
the safety precautions. You also need to comply with relevant international, national, or regional
standards and industry practices.
Only qualified professionals or trained personnel are allowed to perform operations on the
equipment. Operation personnel shall understand the system, its working principles, and relevant
national/regional standards.
Use insulated tools when installing the device. For personal safety, wear proper personal
protective equipment (PPE).
Introduction
Rear
Heat exchange
compartment
Nameplate
Rectifier
Main control Ground Main control
front door
rear door rear door bar
(RRD) (MCRD) (MCFD)
Indicators
Indicator Status
Off
Steady on
RUN (green)
Blinking quickly (1 Hz)
Blinking slowly (0.25 Hz)
Off
ALM (red)
On
Specifications
Item
Dimensions (H × W × D) 2150 mm × 800 mm × 1700 mm
Weight <1500 kg (including coolant)
400 V AC, 50/60 Hz, three-phase, five-wire
Rated input voltage
Output voltage range 200-1000 V DC
Rated output power 600 kW
Operating temperature -35°C to +50°C
Transporting temperature -35°C to +70°C
-35°C to +70°C
Storage temperature
Operating humidity 5%–95% RH (non-condensing)
Altitude 0–4000 m (derated if the altitude exceeds 2000 m)
Acoustic pressure level: ≤ 60 dBA at 1 m and 25°C
Noise level
IP rating IP55, Class C environments
and operating environment (IP rating for the heat exchanger compartment: IP20)
NOTICE
Before installing, ensure that:
- the base for the cabinet is built;
- the cables are routed;
- the upstream circuit breakers are OFF;
- the installation tools are ready.
1. Remove the baffle plates at the bottom and remove the cabinet pallets.
Front
2. Move the cabinet and place it on the base using a crane or a forklift truck.
3. Mark the drilling positions by placing angle brackets to the bottom of the cabinet.
4. (Concrete base for example) Drill holes and install expansion sleeves.
5. Install angle brackets and fastening expansion bolts to secure the cabinet.
6. Ground the cabinet.
1
Removing plates and pallet
Indicators
Emergency
stop button
Rectifier
AC input
front door
door
(RFD) (AID)
Cabinet Status
3
There is no AC input.
There is AC input.
Upgrade is in progress.
The equipment is hibernating.
There is no alarm or fault
that causes charging failure.
There is an alarm or fault
that causes charging failure.
Description
Before connecting cables, open all doors and remove all cable hole covers using the delivered socket wrench.
CAUTION
Coolant has been filled before
delivery. Exercise caution when
installing the cabinet to prevent
leakage.
Installing the Cabinet
2
Placing the cabinet
≤ 60°
Horizontally-bound
lifting rope required
or
Protruding fork arms
from the other side
Securing and grounding the cabinet
50 mm
M12
288 mm
Removing Cable Hole Covers
Delivered with
the cabinet
46 N·m