Champion Power Equipment 501353-N Operator's Manual
  1. Manuals
  2. Brands
  3. Champion Power Equipment Manuals
  4. Chippers/Shredders
  5. 501353-N
  6. Operator's manual
Champion Power Equipment 501353-N Operator's Manual

Champion Power Equipment 501353-N Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATOR'S MANUAL
MODEL #501353-N
3 iN. (7.6 cM) chiPPER ShREDDER
READ AND SAVE ThiS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product. Failure to
do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
REV 20240607
Champion Power Equipment, Inc.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 501353-N and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Champion Power Equipment 501353-N

Summary of Contents for Champion Power Equipment 501353-N

  • Page 1 This manual should remain with the product. Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice. REV 20240607 Champion Power Equipment, Inc.

  • Page 2: Table Of Contents

    TAbLE Of cONTENTS 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER TAbLE Of cONTENTS Maintenance ..........Changing the Engine Oil ......... introduction ...........

  • Page 3: Introduction

    501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER iNTRODUcTiON SAfETY DEfiNiTiONS Congratulations on your purchase of a Champion Power Equipment The purpose of safety symbols is to attract your attention to (CPE) product. CPE designs, builds, and supports all of our possible dangers.

  • Page 4: Important Safety Instructions

    SAfETY iNSTRUcTiONS 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER iMPORTANT SAfETY iNSTRUcTiONS WARNiNG  Operation of this equipment may create sparks that can start DANGER  fires around dry vegetation. Engine exhaust contains carbon monoxide, a colorless, A spark arrestor may be required. The operator should contact odorless, poison gas.

  • Page 5: Fuel Safety

    SAfETY iNSTRUcTiONS 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER fuel Safety WARNiNG  Operator Work Zone Area DANGER  Keep work zone clear of debris while working to ensure safe GaSolinE anD GaSolinE VaPorS arE hiGhlY footing. FlammaBlE anD EXPloSiVE.

  • Page 6: Training

    SAfETY iNSTRUcTiONS 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER WARNiNG WARNiNG   When adding or removing gasoline: When storing the chipper shredder: Do not light or smoke cigarettes. Store away from sparks, open flames, pilot lights, heat and other sources of ignition.

  • Page 7: Preparation

    SAfETY iNSTRUcTiONS 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER 5. Check to make sure the chipper-shredder is on a level WARNiNG  surface that is not asphalt, concrete or harden ground. Block the wheels and ensure support leg is secure to prevent...

  • Page 8: Maintenance, Transport And Storage

    SAfETY iNSTRUcTiONS 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER – Only attempt to unclog with a small diameter stick that can get chipped. – If a major clog occurs; turn the fuel valve off and let the unit run until dry, turn off the engine, let the unit cool down, unplug the spark plug wire and take apart the unit to see where the clog has occurred.

  • Page 9: Safety And Dataplate Labels

    Indice d’octane minimal de 87. Maximum 10 % d'éthanol. This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for outside parties without the explicit consent of Champion Power Equipment.
  • Page 10 AVERTISSEMENT on white substrate. This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for NETTOYER PANNEAU D'ACCÈS - ne pas outside parties without the explicit consent of Champion Power Equipment.

  • Page 11: Safety Symbols

    SAfETY iNSTRUcTiONS 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER Safety Symbols Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to more safely operate the product.
  • Page 12 SAfETY iNSTRUcTiONS 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER SYmBol mEaninG amputation hazard. Contact with rotating blades will cause serious injury. Keep hands out of openings while machine is running. Toxic Fumes. The engine exhaust from this product contains chemicals known to the state of California to cause cancer and birth defects and other reproductive harm.

  • Page 13: Operation Symbols

    1. Check oil level. Recommended oil is 10W-30. This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for outside parties without the explicit consent of Champion Power Equipment.

  • Page 14: Controls And Features

    AND fEATURES 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER cONTROLS AND fEATURES Read this operator’s manual before operating your chipper-shredder. Familiarize yourself with the location and function of the controls and features. Save this manual for future reference.

  • Page 15: Engine

    AND fEATURES 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER Engine muffler oil Drain Bolt – Used to drain the oil from the engine. air Filter – Protects the engine by filtering dust and debris oil Fill Cap/Dipstick – Used to check and fill oil level.

  • Page 16: Parts Included

    AND fEATURES 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER Parts included hardware Part Part Qty. hardware needed Tool needed Qty. Flange Bolt M8 × 20 1× 12 mm wrench or socket Hopper Support Lock Nut M8, Flange 1× 12 mm wrench or socket...

  • Page 17: Assembly

    ASSEMbLY 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER ASSEMbLY 2. Thread two M6 lock nuts onto the threaded studs to secure the shredder hopper to the shredder hopper support bracket Your chipper-shredder requires some assembly. This unit ships and tighten securely using a 10mm socket or wrench.

  • Page 18: Collection Bag

    ASSEMbLY 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER collection bag Recommended Engine Oil Type The collection bag can be attached and removed from the chute 10W-30 deflector using the adjustable drawstring. It is recommended to 5W-30 10W-40 be attached before operation and removed before completely full, after operation, or before storage.

  • Page 19: Add Fuel

    ASSEMbLY 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER Use clean, fresh, regular unleaded gasoline with a minimum cAUTiON  octane rating of 91 and an ethanol content of 10% or less by volume. y b c The engine is equipped with a low oil shut-off and will stop when the oil level in the crankcase falls below the threshold DO NOT mix oil with gasoline.

  • Page 20: Operation

    OPERATiON 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER NOTicE WARNiNG   The engine works well with 10% or less ethanol blended During operation the muffler and exhaust fumes produced will gasoline. When using ethanol-gasoline blends there are some become hot.

  • Page 21: Before Each Use Inspect The Chipper-Shredder

    OPERATiON 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER before Each Use inspect the chipper- 3. Move the choke lever to the “CHOKE” position. Shredder 1. Always make sure the spark plug wire has been disconnected and engine has been grounded.

  • Page 22: Chipper-Shredder Operation

    OPERATiON 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER 6. Make sure the materials that are going to be chipped or NOTicE  shredded are free of any rocks, trash, metals and other foreign objects. Keep choke lever in “CHOKE” position for only 1 pull of the recoil starter.

  • Page 23: Chipping And Shredding Tips

    OPERATiON 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER chipping and Shredding Tips NOTicE  Chipping After all material has been processed it is recommended that 1. Make sure wood is less than 3 in. (7.6 cm) in diameter. the unit run for short period of time to clear out any left over material that may still be in the chutes or flail housing.

  • Page 24: Operation At High Altitude

    MAiNTENANcE 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER Operation at high Altitude under normal operation 1. Move the fuel valve to the “OFF” position. The density of air at high altitude is lower than at sea level. Engine power is reduced as the air mass and air-fuel ratio decrease.

  • Page 25: Changing The Engine Oil

    MAiNTENANcE 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER WARNiNG WARNiNG   Improper maintenance will void your warranty. Used oil is a hazardous waste product and must be disposed of properly. Do not discard with household waste. Check with your local authorities, service center, or dealer for safe NOTicE ...

  • Page 26: Chipper-Shredder Maintenance

    MAiNTENANcE 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER chipper-Shredder Maintenance 2. Using a 15mm socket, remove the M10 lock nuts securing the chipper chute to the front of the chipper and remove the Make certain that the chipper-shredder is kept clean and stored chipper chute to access the knives.
  • Page 27 MAiNTENANcE 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER 5. Inspect the shredder blade (A), flail blades (B), spacers (C), chipper blades (D) and hardware (nuts, bolts and washers). If any of the parts show signs of wear and/or damage, replace them.

  • Page 28: Maintenance Schedule

    MAiNTENANcE 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER Maintenance Schedule 4. To remove the impeller assembly from the inner flail housing, use a 5/8 in. socket to remove the bolt in the center of the Follow the service intervals indicated in the following maintenance assembly (A).

  • Page 29: Storage

    STORAGE 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER STORAGE Refer to the Maintenance sections for proper cleaning instructions. Always disconnect the spark plug wire in times of inactivity, maintenance, and storage. This will help to prevent any unintended engine start ups.

  • Page 30: Specifications

    SPEcificATiONS 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER SPEcificATiONS Spark Plug Specifications OEM Type ............. F6RTC chipper-shredder Specifications Replacement Type ...... NGK BPR6ES or equivalent Max Diameter Chipper Material .

  • Page 31: Chipper Shredder Parts Diagram

    ShREDDER PARTS DiAGRAM 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER chiPPER ShREDDER PARTS DiAGRAM...

  • Page 32: Chipper Shredder Parts List

    ShREDDER PARTS LiST 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER chiPPER ShREDDER PARTS LiST Part number Description Qty. Part number Description Qty. 41 2540006603 2540007161 Engine, 338cc Feed Hopper Assembly, Yellow 10305695 Junction Plate Assembly, Engine 42 2540006575...

  • Page 33: Chipper Shredder Parts Diagram

    ShREDDER PARTS DiAGRAM 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER chiPPER ShREDDER PARTS DiAGRAM...

  • Page 34: Engine Parts List

    ENGiNE PARTS LiST 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER ENGiNE PARTS LiST Part number Description Qty. Part number Description Qty. 12032-000001 Clinder Head Bolt, White Zn Air Cleaner Foam Element, 17151-000011 153×127×18 Cylinder Head Cover Gasket 12034-000001 Assy, White Zn...
  • Page 35 ENGiNE PARTS LiST 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER Part number Description Qty. Part number Description Qty. 90547-000009 Bearing, 6207 96101-Z120410- Cylinder Head assembly 0006 16400-000005 Governor Gear Assy 96105-Z16100- 11411-000004 Crankcase Cover Carburetor assembly 0023 15010-000007 Oil Dipstick Assy 115 30431-000016 Rubber Jacket, Ø9.5 x Ø11 x 90...

  • Page 36: Troubleshooting

    TROUbLEShOOTiNG 501353-N - 3 iN. (7.6 cM) chiPPER ShREDDER TROUbLEShOOTiNG Problem Cause Solution No fuel. Add fuel. Engine will not start. Faulty spark plug. Replace spark plug. Unit loaded during start up. Remove load from unit. Fill crankcase to the proper level.

Table of Contents