1. Manuals
  2. Brands
  3. Finish Thompson Manuals
  4. Engine
  5. S Series
  6. Operations & parts manual

Finish Thompson S Series Operations & Parts Manual

Motors for ef series pumps
Hide thumbs

Advertisement

Table of Contents

S SERIES MOTORS
OPERATION & PARTS MANUAL
for EF Series Pumps
Models S1, S2, S3, S4
P/N 107318 R6
S4
S1, S2, S3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the S Series and is the answer not in the manual?

Questions and answers

Related Manuals for Finish Thompson S Series

Summary of Contents for Finish Thompson S Series

  • Page 1 S SERIES MOTORS OPERATION & PARTS MANUAL for EF Series Pumps Models S1, S2, S3, S4 P/N 107318 R6 S1, S2, S3...
  • Page 2 EU Declaration of Conformity Finish Thompson Inc. hereby declares that the following machine(s) fully comply with the applicable health and safety requirements as specified by the EU Directives listed. The product may not be taken into service until it has been established that the drive motor for the centrifugal pump complies with the provisions of all relevant EU Directives.
  • Page 3 EU Declaration of Conformity Finish Thompson Inc. hereby declares that the following machine(s) fully comply with the applicable health and safety requirements as specified by the EU Directives listed. The product may not be taken into service until it has been established that the drive motor for the centrifugal pump complies with the provisions of all relevant EU Directives.
  • Page 4 Any use other than that described herein is considered incorrect; consequently, Finish Thompson Inc. shall not be held responsible for any damages to people or things. In case of doubt or enquiries, please apply to our Technical Service department directly at the following address: Finish Thompson, Inc.
  • Page 5 The warranty of the products shall be valid for a period of 12 months from the date of delivery, under the condition that notice of the alleged defect to the products or parts thereof be given to Finish Thompson, Inc. within the term of 8 days from the discovery.

  • Page 6: For Your Own Safety

    1. Introduction This manual contains all the information needed for the correct installation, use and maintenance of your new Finish Thompson motor. It should be read and understood by all the personnel involved in installation, operating and servicing of the pump before it is started.

  • Page 7: Pour Votre Sécurité

    écrite de Finish Thompson Inc. On demande d’utiliser seulement les pièces de rechange origina les de Finish Thompson Inc. et les accessoires approuvés. Le fait de ne pas utiliser les pièces de rechange originales de Finish Thompson Inc.
  • Page 8 IMPORTANT SAFETY INFORMATION FOR PUMPING FLAMMABLE OR HAZARDOUS SUBSTANCES Read these instructions before operating the pump and motor equipment. The manufacturer will not be responsible for any damage to property or to persons caused by improper use of the equipment. WARNING: It is the responsibility of the user to operate the pump in conformance with OSHA rules for dispensing liquids.

  • Page 9: Installation

    INSTALLATION Unpack motor and pump tube from carton. Check for shipping damage. If damage is detected, save the packaging and notify the carrier immediately. 2. If motor and pump tube are boxed separately, the motor will need to be fastened to the pump tube. See figures 1 & 2. Figure 1 Figure 2 Place the motor upside down on a tabletop surface with the coupling facing upwards and place the yellow coupling insert (item...

  • Page 10: Operation

    Air motor – Turn the air motor ball valve to the closed position. Attach the air motor to an air supply line filtered, lubricated (use detergent SAE #10 oil) and regulated to 40 psi and 27 CFM using a ¼” FNPT fitting. (Note: Finish Thompson offers an optional Filter / Lubricator, P/N A100003.) Insert the pump tube into the fluid to be dispensed and the hose in the container to be filled.

  • Page 11: Specifications

    MOTOR SPECIFICATIONS ELECTRIC MOTORS (2 SPEED) AIR MOTOR SPECIFICATIONS MODEL S1 MODEL S2 MODEL S3 MODEL S4 s t l s t l s t l RPM (low / high speed) 8,000 / 14,000 8,000 / 14,000 8,000 / 14,000 300 - 11,000 Max.
  • Page 12 PARTS LIST – ELECTRIC MOTORS Models S1, S2 & S3 PART NUMBER ITEM DESCRIPTION MODEL S1 MODEL S2 MODEL S3 115V US CORD 107215 230V EU CORD 107216 115V UK CORD 107216-1 TRIAC ASSEMBLY - 115V 107265-1 107265-1 TRIAC ASSEMBLY - 230V 107265-2 ON/OFF SWITCH 107304...

  • Page 13: Parts List - Air Motor

    PARTS LIST - AIR MOTOR Model S4 MODEL S4 PARTS LIST ITEM DESCRIPTION PART NO. AIR MOTOR ONLY J100032 AIR MOTOR ADAPTER 107073 COUPLING HALF J103934 NIPPLE J100107 HEX REDUCER BUSHING J100057 BALL VALVE J100073 UNION - BRASS J100036 SET SCREW J100040 MUFFLER J100033...

This manual is also suitable for:

S1S2S3S4

Table of Contents