Summary of Contents for Century CA3000L Series
- Page 1 User Manual of Century RF System Standard Series (CA3000L Mainboard) Firmware: V2.08, Software: V1.16, Manual version: V1.01 Copyright © 2019 Hangzhou Century Co., Ltd. All rights reserved.
-
Page 2: Revision History
Revision History Date Revision Description 12/15/2016 1.00 First Release 04/22/2017 1.01 Installation scheme added... -
Page 3: Table Of Contents
Content 1．GENERAL INFORMATION ..............3 2．OVERVIEW OF SYSTEMS ............... 4 2.1．Appearance & Structure of Antenna ................4 2.2. Power Supply Unit ......................4 2.3．Synchronization ......................5 2.4．Alarm .......................... 5 2.4.1．Alarm and Background Light ................... 5 2.4.2．Relay Output ......................5 2.4.3．PCB Layout and Wire Connection ................6 3. -
Page 4: 1．General Information
1．GENERAL INFORMATION The electronics inside antennas are extremely sensitive to electrostatic discharges. Always discharge yourself by touching a ground point before touching any of the electronics to avoid damaging the circuits. WARNING The electricity supplied to the systems shall not be shared with other electronic or electric loads, e.g. -
Page 5: 2．Overview Of Systems
2．OVERVIEW OF SYSTEMS 2.1．Appearance & Structure of Antenna CA3000L 2.2. Power Supply Unit One power adapter is preferred to work with one CA3000L mainboard only. If the quality WARNING: of power source is not good enough, the external filter shall be used (as shown below). WARNING: Do not tie 24V and 220V cables together, as AC may generate interference to the system. -
Page 6: Synchronization
Century Mono RF systems are compatible with other Mono systems. But Dual systems can interfere with all Mono systems (not only Century’s). So, Century Mono systems must be kept at least ten (10) meters away from any Dual system. Otherwise, the performance of the Mono systems will be affected. -
Page 7: Pcb Layout And Wire Connection
2.4.3．PCB Layout and Wire Connection (1&4—O) (2&5—8) (3&6—88) Noise Indicator Fuse DC Out DC In RX1 Loop RX2 Loop TX Loop WIFI Power Indicator CCTV Buzzer Light Volume RS 232 Status Indicator Alarm LED DSP In Power Level RX Gain... -
Page 8: Hardware Adjustments And Tsets
3. HARDWARE ADJUSTMENTS AND TSETS 3.1．LED Indicators LED colour Name Description LED1 The power is normal LED02 Noise Level 7 Noise High LED03 Noise Level 6 LED04 Noise Level 5 The higher noise LED05 Noise Level 4 level, the worse YELLOW LED09 Noise Level 3... -
Page 9: 4．Software Configuration
4． SOFTWARE CONFIGURATION For the software configuration, RFC software is required. And a T-cable is needed for connection between PC and the CA3000L mainboard. A dongle is optional for security purpose based on specific requirement. T-Cable and port of connection on CA3000L Dongle with license data 5．INSTALLATION GUIDE 5.1 Recommended Arrangement of Antenna Frame and Door Frame... -
Page 10: Preparation Before Installation
Note: Different orientations of labels will have varied detection distance. 6. SERVICE SUPPORT If you have any questions or suggestions about the Essential Series of Century AM systems, please do not hesitate to contact our technical support by email technicalsupport@century-cn.com, or our salespersons... -
Page 11: Fcc Statement
FCC Statement： Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the CA3000L Series and is the answer not in the manual?
Questions and answers