Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for scigiene IFD3000
- Page 1 IFD3000 Intelligent Fluorescence Detector...
-
Page 2: Table Of Contents
CONTENTS 1. Notes .......................... 1 2. Introduction ........................2 2.1 Preface ......................2 2.2 Product feature ....................2 2.3 Performance parameter ..................3 2.4 External structure ....................3 2.5 Accessories and the matching test reagents (optional) ........4 3. Basic Operation ......................5 3.1 Startup interface .................... -
Page 3: Notes
1. Notes Please read the instruction manual carefully before you operate the instrument, so as to ensure a correct use and avoid any unnecessary damage due to improper operation. Note: Always take basic security precautions, including all contents listed as below. Please read in detail before using the instrument: Test whether the voltage configuration is matching the voltage requirement of the instrument. -
Page 4: Introduction
2.2 Product feature IFD3000 Intelligent Fluorescence Detector adopts highly sensitive photodiode to detect the bioluminescence produced by the detection reagent. According to the strength of the bioluminescence signal, the experimental results are calculated and analyzed, and the detection results can be obtained quickly and easily. -
Page 5: Performance Parameter
The instrument is small and light, rapid detection, the average detection time is just ⚫ 15 seconds per once. 2.3 Performance parameter The performance parameters of this instrument are as following: Dimension: (L * W * H) 189.5 mm * 34 mm * 89 mm. ⚫... -
Page 6: Accessories And The Matching Test Reagents (Optional)
Front structure of the instrument, as shown in Figure 1: Test chamber cover, the cover must be tightly fastened when the instrument is working. Otherwise, the instrument will prompt an error and cannot perform detection. Insertion port for swabs and test tubes (containing reagents to be tested), for fluorescence data detection. -
Page 7: Basic Operation
3. Basic Operation 3.1 Startup interface "Long press" " " the on-off button on the right side of the instrument for 2 seconds, the operation indicator will be lighted up. Release the switch and wait the instrument to start. After the system startup, the startup interface will be displayed as shown in Figure 4 and Figure 5 as below. -
Page 8: Instruction
4. Instruction 4.1 Option interface The intelligent fluorescence detector mainly includes ten functional modules such as Quick Test, Location, Plans, History, Calibration, Thresholds, Inspector, Settings, Cloud Platform and Analysis, as shown in Figure 6. Figure 6 The main interface 4.2 Quick test 4.2.1 Quick test Click the "... - Page 9 Figure 7 Test Figure 8 Test tips interface Thresholds and inspector can be selected through the input data. Note: When select an inspector, you need to input the inspector's password to set up, if the inspector has no password, just click select. The inspector who sets the password can select only after clicking and entering the correct password.
-
Page 10: Testing Procedure
4.2.2 Testing procedure The test diagram is shown in Figure 9. The reagent operation process must strictly follow the requirements of the reagent instructions. The setting details of "Location", "Plans", "History", "Calibration", "Thresholds", "Inspector", "Settings" etc. please refers to the sections 4.3 -- 4.9 of this chapter. ①... -
Page 11: Location
4.3 Location This is to set the specific location information for the detection. For example, experimental platform No. 1 in the second-floor laboratory or other specific locations. Click " ", and the system will immediately enter the location interface, as shown in Figure 10: Figure 10 Locations interface Figure 11 New locations added interface... - Page 12 In the main interface of detection plan, click "Add" button to enter the interface of adding detection plan, as shown in Figure 13. Figure 12 Main interface of detection plan Figure 13 Adding interface Fill in the name of the detection plan and click "Add" to add specific detection locations.
-
Page 13: History
4.5 History Click " " button to enter the main interface of historical record, as shown in Figure 16. This module includes two indicators: "Result" and "Trend", The "Result" mode can display the three result data of "Pass", "Caution" and "Fail" as well as the "View all" data. - Page 14 data in the latest 14 days. It can display the number of detection information of failed, caution and passed in the form of charts. You can also search through detection plan and detection location to view the corresponding detection results. Click "Clear History"...
-
Page 15: Calibration
4.6 Calibration Click the " " icon, the instrument will start automatic calibration, and shut down automatically after calibration, as shown in Figure 20. Please test again after "calibration" to ensure that the instrument detects accurately. The instrument has automatic identification and calibration function during use, which can effectively ensure the stability of the instrument. -
Page 16: Inspector
Figure 21 Threshold setup interface Figure 22 Threshold added interface Click “Add” to enter the threshold adding interface, (as shown in Figure 22), then enter the threshold name, upper and lower limits (described as High and Low as in above chart). Note: the input value should also be the same as the above "Thresholds"... -
Page 17: Settings
The main interface includes "Search" and "Add" functions. All added "inspector" will be displayed in the current interface. Click the "Add" button in the main interface, and the "Add inspector" window will pop up (as shown in Figure 24). Input the inspector and password, then save it after confirmation. -
Page 18: Wireless Network Setting
4.9.1 Wireless Network Setting Configure instrument wireless (WIFI) network through this function. 4.9.2 Bluetooth Setting Configure instrument Bluetooth signal through this function. 4.9.3 Date and Time Setting Adjust instrument time through this function. 4.9.4 Sleep Time Setting Through this function to adjust the instrument ”Breathing plate time”, "Sleep" and "Shutdown"... -
Page 19: Check For Updates
pieces of historical data, the password will pop up for inputting, and the deletion can only be done after entering the correct management password. If you forget your admin password, please contact customer service to reset your password. After getting the reset password, enter the data management interface and click "Password Reset". -
Page 20: Cloud Platform
4.10 Cloud platform Cloud Platform synchronization function: Upload and synchronize detection data to the cloud platform. You can also obtain detection information from the corresponding account of the cloud platform (Location, Plans, Thresholds, Inspector, History). The steps for synchronizing the cloud platform data are as follows: Click the “Cloud platform”... -
Page 21: Analysis
The steps for synchronizing the analysis software data are as follows: (1) Install the analysis software IFD3000.exe into the computer, after the installation is completed, click on the "Data synchronism", the interface as shown in Figure 28. -
Page 22: Instrument Maintenance
5. Instrument Maintenance 5.1 Routine maintenance IFD3000 Intelligent Fluorescence Detector is a precision testing instrument, in order to keep the instrument in a good state, the routine maintenance must be conducted well. Avoid Strong light!! ⚫ Using neutral detergent or wet cloth for surface cleaning of the instrument. -
Page 23: Wireless Network Troubleshooting List
5.2.2 Wireless network troubleshooting list Instruments and routers have been opened and connected power supply, at the same ⚫ time ensure the wi-fi is open and function well. If the wireless network running well, please try to access other devices in the wireless ⚫...
Need help?
Do you have a question about the IFD3000 and is the answer not in the manual?
Questions and answers