Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DitoGear MODULO DOLLY B
Summary of Contents for DitoGear MODULO DOLLY B
- Page 1 MODULO DOLLY B USER’S MANUAL...
-
Page 2: Table Of Contents
Motor warning signals and behaviors Operation modes and angles In the box Assembly - the trolley Assembly - the track Technical specifications Conservation Guidelines Using 3rd party power adapters Using DitoGear™ Power Packs Obtaining Support Limited Warranty Privacy Miscellaneous ... -
Page 3: Getting Started
Depending on the weight of your camera setup, it can also be operated slightly tilted or even vertically In case of working in camera or other equipment caused by improper use of vertical orientation, a DIY counterweight is recommended DitoGear™ is not responsible for any damage to the equipment Detailed instructions related to these controllers have been the device. -
Page 4: In The Box
4 In the box MODULO DOLLY B PARTS QUANTITY 1m Track Unit 2 Building Rods 3 Servo Motor Unit 4 Traction Belt (meter) 5 End Block 6 Trolley Base 7 Rod Mounting Clip 8 Spreader 9 Traction Belt Clamps Set... -
Page 5: Assembly - The Trolley
5 Assembly - the trolley Attach four pairs of Rod Mounting Clips to the Trolley Base The Rod Mounting Clip without thread should be located between the Trolley Base and the threaded Rod Mounting Clip Do not tighten the bolts Attach two Traction Belt Rollers to the Servo Motor Unit Rollers should rotate freely... - Page 6 Insert each of Building Rods into two pairs of Rod Mounting Clips Tighten the bolts Use two bolts to attach the Servo Motor Unit underneath the Trolley Base...
- Page 7 Make sure the Servo Motor Unit is properly attached to the Trolley Base Connect one set of Trolley Sidewheels (Trolley Base Block + Trolley Bearings) to Building Rods and the Trolley Base and the Servo Motor Unit...
-
Page 8: Assembly - The Track
6 Assembly - the track Connect each of End Blocks to Support Feet with two bolts (Optional) Attach two Traction Belt Clamps Sets to End Blocks using 1-inch-long bolts... - Page 9 If you have multiple Track Units, connect them together in pairs Install the Spreader(s) between two opposite Track Units Loosen the clamps if necessary Insert Track Units into End Blocks Loosen the clamps if necessary...
- Page 10 Add the second set of Trolley Sidewheels and mount the trolley on Track Units Tighten the bolts to stabilize the trolley The tension should be sufficient to keep the trolley on the track, but you should avoid excessive tension which may result in high friction of the trolley on the track...
- Page 11 Loosen the marked bolts to move the Trolley Base on Building Rods Two Traction Belt Clamps Set should Undo the clamp of Traction Belt Clamps Set to fix the Traction Belt be aligned with the Servo Motor gear...
- Page 12 Install the Traction Belt as on the picture below Adjust tension of the Traction Belt coarsly and attach it to the second Traction Belt Clamps Set...
- Page 13 Make sure the Traction Belt is properly fastened and that the tension is sufficient not to skip the gears as Belt tension can be further enhanced by adjusting the position of each End Block the trolley moves Modulo Dolly B hardware is ready for operation Proceed with connecting DitoGear™ Motion controller(s) as described in their respective manuals...
-
Page 14: Technical Specifications
0 8A - 1 1A(at 12V DC) up to 8h on a new and charged 7Ah kit battery After use make sure to clean the DitoGear™ Modulo Drive and all DitoGear™ Modulo parts with a soft fabric You Battery operating time in timelapse mode at 15°C... -
Page 15: Using 3Rd Party Power Adapters
Caution! DitoGear is not responsible for any damage or failures caused by the use of a 3rd party power supply adapter. For consumers, who are covered by consumer protection laws or regulations in their country of purchase or, if different, 10 Precautions for Safe Use of DitoGear™... -
Page 16: Exclusions And Limitations
DitoGear’s property Parts provided by DitoGear in fulfillment of its warranty obligation must by anyone who is not a representative of DitoGear; (g) to a product or part that has been modified to alter functionality or be used in products for which warranty service is claimed When a refund is given, the product for which the refund is capability without the written permission of DitoGear;... -
Page 17: Privacy
The device and all batteries included with it must be disposed of properly according to local laws and regulations The product must be disposed of separately from the household waste When your product reaches its end of life, contact DitoGear or your... - Page 18 W W W DITOGE AR COM...
Need help?
Do you have a question about the MODULO DOLLY B and is the answer not in the manual?
Questions and answers