Advertisement
LED Light Kit
Sand Pro
Model No. 08740
Important:
Before installing this light kit on Sand Pro Model 08703 or Model 08705 machines with serial
number 408784373 or lower, or on Model 08745 machines within the serial range of 411839064 through
411839074, you must install kit Model No. 140-0333.
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
© 2022—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
3040 or 5040 Traction Unit
Description
No parts required
Carriage bolt (5/16 x 1 inch)
Front support
Lock washer (3/16 inch)
Nut (3/16 inch)
Rear bracket
Wire harness
No parts required
R-clamp
Flange head capscrew (5/16 x 5/8 inch)
Cable tie
Fuse (10 A)
No parts required
Register at www.Toro.com.
Form No. 3443-276 Rev B
Installation Instructions
Qty.
–
Prepare the machine.
2
1
2
Prepare the light
2
1
1
Route the wire harness.
–
Install the dash switch.
1
Assemble the front light to the machine.
2
5
Secure the wire harness.
1
Install the fuse.
–
Finish the LED light kit installation.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Use
*3443-276*
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Toro 08740
Summary of Contents for Toro 08740
- Page 1 LED Light Kit Sand Pro ® 3040 or 5040 Traction Unit Model No. 08740 Installation Instructions Important: Before installing this light kit on Sand Pro Model 08703 or Model 08705 machines with serial number 408784373 or lower, or on Model 08745 machines within the serial range of 411839064 through 411839074, you must install kit Model No.
-
Page 2: Preparing The Machine
Preparing the Machine No Parts Required Parking the Machine Park the machine on a level surface, move the g283342 traction pedal to the position, move NEUTRAL the throttle switch to the low-idle position, and lower the attachments; refer to your machine Operator’s Manual. - Page 3 Removing the Center Shroud Move the dash panel rearward to provide access to the front side of the panel (Figure Evenly loosen the 2 capscrews that secure the center shroud to the machine (Figure Note: The capscrews are captive fasteners, and have a retainer that keeps the screw with the cover.
- Page 4 Assemble the light and carriage bolt to the front support with the lock washer (3/16 inch) and nut (3/16 inch) as shown in Figure g283355 Figure 7 g283352 1. Carriage bolt (5/16 x 1 3. Lock washer (3/16 inch) Figure 5 inch) 1.
- Page 5 Tighten the nut by hand. Assembling the Light to the Rear Bracket Assemble the light and carriage bolt to the rear bracket with the lock washer (3/16 inch) and nut (3/16 inch) as shown in Figure g283432 Figure 10 1. 2-socket connector (kit 3.
- Page 6 Rotate the operator’s seat forward (Figure 15). g283434 Figure 12 g283451 Figure 15 1. Kit wire harness 2. Steering-support tube Route the 8-socket connector of the wire Route the wire harness along the right side of harness to the left side of the dash panel (Figure the machine, rearward along support tube for 13).
- Page 7 g283465 Figure 19 1. Dash panel opening 2. Switch g283438 Figure 17 Plug the 8-socket connector of the kit wire harness onto the connector of the switch (Figure 1. 2-socket connector (kit 2. Document tube wire harness—labeled 20). REAR HEAD LIGHT Connecting the Dash Components g283470...
- Page 8 g283471 Figure 21 1. 2-socket connector 2. 2- pin (kit wire harness) (machine wire harness—labeled OPTIONAL LIGHT KIT g283474 Figure 22 1. Front support (LED light) 4. Kit wire harness 2. R-clamp 5. Castor Fork Installing the Front LED 3. Flange head capscrew (5/16 x 5/8 inch) Lights Align the holes in the front support and the...
- Page 9 Assembling the Front Light to the Machine Machines with the Front Lift Kit Remove the 2 capscrews (3/8 x 2 inches) and 2 locknuts (3/8 inch) that secure the guide brackets for the front lift kit to the caster-fork bracket (Figure 23).
- Page 10 g283505 Figure 25 1. 2-pin connector (LED 2. 2-socket connector (kit Light) wire harness—labeled FRONT HEAD LIGHT g344322 Assembling the Rear Light to the Machine Remove the 2 capscrews (5/16 x 5/8 inch) and 2 flange locknuts (5/16 inch) that secure the document tube R-clamps to the rear cover of the machine (Figure...
- Page 11 Secure the kit wire harness with a cable tie at the rear brace of the frame (Figure 30). g283505 g283596 Figure 28 1. 2-pin connector (LED 2. 2-socket connector (kit Light) wire harness—labeled REAR HEAD LIGHT Securing the Wire Harness g283598 Figure 30 Parts needed for this procedure:...
- Page 12 Tighten the 4 capscrews that secure the side-control console to the machine (Figure 29). Secure the kit wire harness to the machine wire harness and hydraulic tube as shown in Figure g283594 Figure 33 1. Machine wire harness 3. Cable tie 2.
-
Page 13: Installing The Fuse
Installing the Fuse Parts needed for this procedure: Fuse (10 A) g283511 Figure 36 Procedure Insert the fuse (10 A) into slot 3 of the fuse block (Figure 35). Align the holes in the dash panel with the holes in the frame bracket (Figure 37). -
Page 14: Operation
Operation Operating the Lights With the ignition key in the run position Start the engine; refer to the Operator’s Manual. Use the light switch as follows: • Push the light switch (Figure 40) up to turn on the lights. Both lights illuminate. •... - Page 15 Notes:...
Need help?
Do you have a question about the 08740 and is the answer not in the manual?
Questions and answers