All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by MB/SaS/WS 1169 BU TV Consumer CarePrinted in the Netherlands...
& drivers. Table 2-1 Described Model Numbers: Model Number Styling Published in 19HFL3233D/10 Golden horse 3122 785 19120 19PFL3606H/12 Golden horse 3122 785 19120 19PFL3606H/58...
Page 3
Technical Specs, Diversity, and Connections TPM8.2E LA EN 3 Connections 19120_001_110511.eps 110524 Figure 2-1 Connection overview Note: The following connector colour abbreviations are used 2.3.2 Rear Connections (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Gy= Grey, Rd= Red, Wh= White, Ye= Yellow. 3 - TV ANTENNA - In Signal input from an antenna, cable or satellite.
3.3.3 Spare Parts external damage. • Check the strain relief of the Mains/AC Power cord for For the latest spare part overview, consult your Philips Spare proper function. Part web portal. • Check the electrical DC resistance between the Mains/AC...
EN 6 TPM8.2E LA Precautions, Notes, and Abbreviation List The third digit in the serial number (example: Abbreviation List AG2B0335000001) indicates the number of the alternative B.O.M. (Bill Of Materials) that has been used for producing the 0/6/12 SCART switch control signal on A/V specific TV set.
Page 7
6.5 MHz. L' is Band (VESA standard for communication I, L is all bands except for Band I channel and display). Using E-DDC, LG.Philips LCD (supplier) the video source can read the EDID Loudspeaker information form the display.
Page 8
SOPS Self Oscillating Power Supply Serial Peripheral Interface bus; a 4- wire synchronous serial data link standard S/PDIF Sony Philips Digital InterFace SRAM Static RAM Service Reference Protocol Small Signal Board Spread Spectrum Clocking, used to reduce the effects of EMI...
Mechanical Instructions TPM8.2E LA EN 9 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Figures below can deviate slightly from the actual situation, 4.2 Service Positions due to the different set executions. 4.3 Assembly/Panel Removal 4.4 Set Re-assembly Cable Dressing 19120_100_110511.eps 110511...
Page 10
EN 10 TPM8.2E LA Mechanical Instructions 19120_101_110511.eps 110511 Figure 4-2 Cable dressing 22" Golden horse 2011-Sep-30...
Page 11
Mechanical Instructions TPM8.2E LA EN 11 19121_101_110914.eps 110914 Figure 4-3 Cable dressing 22" Spot Deal 2011-Sep-30...
Page 12
EN 12 TPM8.2E LA Mechanical Instructions 19120_102_110527.eps 110527 Figure 4-4 Cable dressing 26" Golden horse 2011-Sep-30...
Mechanical Instructions TPM8.2E LA EN 13 19121_100_110913.eps 110913 Figure 4-5 Cable dressing 32" Spot Deal Service Positions For easy servicing of a TV set, the set should be put face down on a soft flat surface, foam buffers or other specific workshop tools.
Page 14
EN 14 TPM8.2E LA Mechanical Instructions 2 × 12 M3 × 6 19120_103_110512.eps 110526 Figure 4-6 Rear cover removal 4.3.2 Small Signal Board (SSB) 4.3.3 Power Supply Unit (PSU) Refer to Figure 4-7 for details. Caution: it is mandatory to remount all different screws at their Caution: it is mandatory to remount all different screws at their original position during re-assembly.
Mechanical Instructions TPM8.2E LA EN 15 4.3.6 LCD Panel 19"/22" 1. Release the LVDS connector from the LCD panel. 2. Release the lamp connectors from the PSU. 3. Take out the speakers, as described earlier. 4. Remove the IR/LED board as described earlier. 5.
EN 16 TPM8.2E LA Service Modes, Error Codes, and Fault Finding 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: • Display information (“SDM” or “SAM” indication in upper 5.1 Test Points right corner of screen, error buffer, software version, 5.2 Service Modes operating hours, options and option codes, sub menus).
Page 17
Service Modes, Error Codes, and Fault Finding TPM8.2E LA EN 17 Specifications • Press the following key sequence on the remote control • Set linear video and audio settings to 50%, but volume to transmitter: “062596” directly followed by the OK button to 25%.
Page 18
EN 18 TPM8.2E LA Service Modes, Error Codes, and Fault Finding Table 5-2 SAM mode overview Main Menu Sub-menu 1 Sub-menu 2 Description System Information Op Hour This represents the life timer. The timer counts normal operation hours, but does not count Stand-by hours. Main SW ID e.g.
Page 19
Service Modes, Error Codes, and Fault Finding TPM8.2E LA EN 19 Specifications • 1.4 Option Code 1 Gives the option codes of option group • Ignore “Service unfriendly modes”. 1 as set in SAM. • Line number for every • 1.5 Option Code 2 Gives the option codes of option group line (to make CSM language independent).
Page 20
EN 20 TPM8.2E LA Service Modes, Error Codes, and Fault Finding Stepwise Start-up Standby Soft Mode Command Received, Switch previously in Standby Off(Mains Soft Mode (Power tact Standby Power Plug) switch) Digital Digital background background tasks started tasks completed TV Wakeup commands Received Standby...
USB port. This allows replacement of a software image in a directly available. stand alone set. A description on how to upgrade the main 4. ComPair features TV software up possibilities. software can be found in the DFU or on the Philips website. Specifications 5.5.2 Introduction ComPair consists of a Windows based fault finding program and an interface box between PC and the (defective) product.
EN 22 TPM8.2E LA Service Modes, Error Codes, and Fault Finding 5. To proceed, In next menu select [Start] and press OK to 5.5.6 Content and Usage of the One-Zip Software File start software updates. See Figure 5-9. 6. Upgrading will now begins and the status of the updating Below you find a content explanation of the One-Zip file, and progress will be displayed.
Service Modes, Error Codes, and Fault Finding TPM8.2E LA EN 23 – ERROR: 6 0 0 0 0: Error code 6 is the last and only 5.8.1 NVM Editor detected error. – ERROR: 9 6 0 0 0: Error code 6 was detected first and In some cases, it can be convenient if one directly can change error code 9 is the last detected (newest) error.
EN 24 TPM8.2E LA Alignments 6. Alignments Index of this chapter: Table 6-1 White tone default settings 6.1 General Alignment Conditions 6.2 Hardware Alignments Colour temperature 6.3 Software Alignments Picture mode Screen size Green Blue 6.4 Option Settings Normal (9000K) 19" (Golden horse) 128 6.5 Reset of Repaired SSB 22"...
Page 25
NVM, the set will switch to Stand-by, to indicate that the process has been completed. Table 6-2 Display code overview CTN_ALT BOM# Panel Type Display Code 19HFL3233D/10 LGD LC185WH1-TLG1 19PFL3606H/12 LGD LC185WH1-TLG1 19PFL3606H/58 LGD LC185WH1-TLG1 19PFL3606H/60...
EN 26 TPM8.2E LA Circuit Descriptions 7. Circuit Descriptions Index of this chapter: • Only new circuits (circuits that are not published recently) 7.1 Introduction are described. 7.2 Power Supply • Figures can deviate slightly from the actual situation, due 7.3 Power Management to different set executions.
Page 27
Circuit Descriptions TPM8.2E LA EN 27 7.1.3 SSB Cell Layout ANALOG I/O DC/DC DDR3 MT5366 TUNER ANALOG I/O DIGITAL I/O AUDIO CLA SS - D ANALOG I/O SERVICE CONNECTOR 19120_206_110516.eps 110525 Figure 7-2 SSB layout cells (top view) 2011-Sep-30...
The diversity in power supply units is mainly determined by the regular market. diversity in screen sizes, but please note to always order the Consult the Philips Service web portal for the order codes of the correct replacement. boards. Power Management...
Circuit Descriptions TPM8.2E LA EN 29 Circuit Description DV33 DV15_DDR FB705 FB705 220R/2000mA 220R/2000mA U703 U703 AZ1117D AZ1117D 7.4.1 System power VOUT C725 C725 C730 C730 The main board power is received at connector CN701 from 10uF 16V 10uF 16V C729 C729 R712...
Page 30
EN 30 TPM8.2E LA Circuit Descriptions 7.4.6 NVM (U409) 7.4.8 Audio Mute circuit The system EEPROM is a 128 kB IC. It contains all system This circuit will provide a “high-to-low” pulse when the +5 V settings. SSB power line goes low. This will trigger the related audio mute circuit, preventing the audio circuit making uncontrolled sounds.
Page 31
Circuit Descriptions TPM8.2E LA EN 31 7.4.10 Core Power The circuit around U701 will provide the main 1.1 V power supply to the MT5366 micro processor. DV11 VCCK FB706 FB706 +5V_STB 220R/2000mA 220R/2000mA L701 L701 U701 U701 TPS54319RTE TPS54319RTE 1.5UH 1.5UH C717 C717...
Page 32
EN 32 TPM8.2E LA Circuit Descriptions 7.4.12 Demodulator The MT5135AE provides a high performance DVB-T and • On-chip integrated SAW filter function. DVB-C demodulation function, the integrated CI+ controller • 10-Bit ADC accepting IF or low-IF inputs. and interface also reduces the complexity of TS routing. •...
IC Data Sheets TPM8.2E LA EN 33 8. IC Data Sheets This chapter shows the internal block diagrams and pin electrical diagrams (with the exception of “memory” and “logic” configurations of ICs that are drawn as “black boxes” in the ICs).
Page 34
EN 34 TPM8.2E LA IC Data Sheets Pinning information MT5366 19120_301_110516.eps 110524 Figure 8-2 Pin configuration 2011-Sep-30...
Page 35
IC Data Sheets TPM8.2E LA EN 35 Diagram DVB-T+C_DEMOD MT5135 / CI B10, MT5135AE/A LQFP-128 (IC U1011) Block diagram Other demodulators PCMCIA interface interface MT5135AE RSSI PVR playback TS RSSI ADC PVR recording TS CI+ controller RF AGC Demod TS Demod TS DVB-C output...
Page 36
EN 36 TPM8.2E LA IC Data Sheets Diagram SPK AMP / HP AMP / AUD MUX B05, TAS5717 HTQFP-48 10W (IC U602) Block diagram OUT_A 2 HB FET Out OUT_B Serial Order SDIN Audio Noise Port (DAP) Shaper OUT_C 2 HB FET Out OUT_D Protection...
Page 37
IC Data Sheets TPM8.2E LA EN 37 Diagram Power-1 B01, G5173R41D (IC U701) Block diagram VINA G5173R41D Thermal SHDN UVLO Shutdown Logic Enable Boot Comparator Charge 107% Shutdown SHDN Enable Logic Threshold Voltage Reference Current Minimum Boot Sense Clamp UVLO Buffer Erramp Logic and PWM Latch...
Block Diagrams TPM8.2E LA EN 44 Block Diagram ENV57U04D8F IF (+/-) for PAL/SECAM /TDTK-G731 RF Tuner for NAND FLASH DDRIII/64M × 16 Bits PAL/DVB-C/T/T2 128 M × Bits × 1 1.3 GHz × 1 IF (+/-) for DVB C/T 24C128 SPDIF Out I2C for No DVB-T2 MT5366 cvou...
Styling Sheets TPM8.2E LA EN 85 11. Styling Sheets 11-1 Golden horse 19" Golden horse 19" Pos No. Description Remarks BEZEL ASSY REAR COVER BASE _ASSY BASE _NECK 1176 REMOTE CONTROL FOR ELECTRICAL PARTS/ASSEMBLIES SEE WIRING DIAGRAM CHAPTER 9 19120_800_110519.eps 110526 2011-Sep-30...
Page 86
Styling Sheets TPM8.2E LA EN 86 11-2 Golden horse 22" Golden horse 22" Pos No. Description Remarks BEZEL ASSY REAR COVER BASE _ASSY BASE _NECK 1176 REMOTE CONTROL FOR ELECTRICAL PARTS/ASSEMBLIES SEE WIRING DIAGRAM CHAPTER 9 19120_801_110519.eps 110526 2011-Sep-30...
Page 87
Styling Sheets TPM8.2E LA EN 87 11-3 Spot Deal 22" Spot Deal 22" Pos No. Description Remarks BEZEL ASSY REAR COVER BASE _ASSY BASE _NECK 1176 REMOTE CONTROL NOT DISPLAYED FOR ELECTRICAL PARTS/ASSEMBLIES SEE WIRING DIAGRAM CHAPTER 9 19121_800_110914.eps 110922 2011-Sep-30...
Page 88
Styling Sheets TPM8.2E LA EN 88 11-4 Golden horse 26" Golden horse 26" Pos No. Description Remarks BEZEL ASSY REAR COVER BASE _ASSY BASE _NECK 1176 REMOTE CONTROL FOR ELECTRICAL PARTS/ASSEMBLIES SEE WIRING DIAGRAM CHAPTER 9 19120_802_110519.eps 110526 2011-Sep-30...
Page 89
Styling Sheets TPM8.2E LA EN 89 11-5 Spot Deal 32" Spot Deal 32" Pos No. Description Remarks BEZEL ASSY REAR COVER BASE _ASSY BASE _NECK 1176 REMOTE CONTROL NOT DISPLAYED FOR ELECTRICAL PARTS/ASSEMBLIES SEE WIRING DIAGRAM CHAPTER 9 19121_801_110914.eps 110922 2011-Sep-30...
Need help?
Do you have a question about the 19HFL3233D/10 and is the answer not in the manual?
Questions and answers