Related Manuals for Vidalux Lisbon Whirlpool Series
Summary of Contents for Vidalux Lisbon Whirlpool Series
- Page 1 INSTALLATION AND OPERATING MANUAL Lisbon Whirlpool Range INSTALLERS PLEASE NOTE, THESE INSTRUCTIONS ARE TO BE LEFT WITH THE CUSTOMER Technical Support: 01524 489939 Warranty Claims Or Delivery Damage: www.vidalux.co.uk...
- Page 2 VIDALUX CLEAR & BRIGHT WATER SOFTENER Guaranteed to get rid of limescale Live in a hard water area?? Limescale in the kettle and on bathroom fixtures?? Suffering from unknown adverse health effects from this polluted drinking water?? If you have a shower and any feature becomes blocked with limescale and stops working THIS IS...
- Page 3 Thank you for purchasing this product. To guarantee the product delivers a long service life, please ensure it is fi tted and used in accordance with the instructions contained in this booklet. Please check that the boxes contain all the items listed below, and report to us any parts that are missing or damaged prior to assembly and within 48 hours of receipt.
- Page 4 Lisbon Steam and Whirlpool Shower Contents Below is a list of the parts you should have received for the installation of your shower. Please note that several parts may be pre-fi tted in place, such as the monsoon shower head, etc. Please note, the design and shape of parts may change occasionally but will always off er the same or greater functionality.
- Page 5 Tub Base with waste assembly and fl exible waste pipe pre-fi tted. Whirlpool pump and system pre-fi tted. Two straight metal sections and two curved rail sections in a silver fi nish (Front Frame). Thermostatic shower valve and 2 braided hoses. Ceiling with pre-fi tted speaker and fan.
-
Page 6: Important Notice
IMPORTANT NOTICE Before you proceed with fi tting your Vidalux Shower please read and understand the following: By commencing testing and installation of the unit you are agreeing to the Terms and Conditions set out by us: copies of which are available by contacting us by by email or by telephone (details on the cover of this manual). -
Page 7: Before You Begin
Before you begin Assembly requires two persons. Tools needed to assemble this shower cabin: Electric screwdriver with a selection of heads, regular screwdrivers, pipe grips, spanners, spirit level, sharp knife and rubber mallet. Connection of the electrical supply and plumbing may require additional tools. Do not fully tighten any screw fixings initially during build as this allows the frame to move a little and aid location of all holes and screws;... - Page 8 Assembly Do not fi t the shower into locations where you do not have at least 40cm access all around the cabin both for installation and for future service access. We advise you do not fi t sinks, toilets etc that restrict access behind the shower.
-
Page 9: Fitting The Control Panel
LEVELING AND FITTING THE TUB Remove the protective fi lm covering the tub base. Connect the soil pipe, trap and any couplings to the fl exible waste under the tub. You may choose to fi t either a HEPV0 trap with the appropriate couplings or choose to fi t a McAlpine ST28M coupling to a McAlpine 28-NRV trap. - Page 10 FIXING REAR GLASS PANELS Locate the two rear, framed glass panels. The inside edge to go to the center control panel will be flat. The outside end to connect to the frame work will have a 'T' end and 90 degree return. . NOTE: A bead of sealant MUST be run between all joining faces of any panel to provide an extra level of sealing, this includes under the side panels and center column where it sits on the tray.
-
Page 11: Front Frame
FRONT FRAME Locate the two silver coloured upright frame sections and the two curved frame rail sections. You will need the 8 x LONGEST screws to join these sections together. The inside facing edges of the rails will be tapered, while the flat edge will meet the tray and the other will be closest to the bathroom ceiling. - Page 12 FITTING THE FRONT FRAME Place the front frame in to position and align the back panels and center column on the tray for fixing NOTE: A large bead of sealant MUST be run between the back panels and Front Frame work to provide an extra level of water protection.
- Page 13 INSTALLING THE FIXED SIDE GLASS PANELS Locate the two fi xed glass panels. These are diff erent from the doors as they do NOT have any holes pre- drilled. Now position this glass panel up to the frame pushing the long edge of the glass into the upright of the frame until FULLY bedded into the frame upright.
- Page 14 SHOWER CEILING Remove the protective fi lm from the roof/ceiling. If not already pre-fi tted, fi t the monsoon rain shower head into the centre of the roof. It is held in place with a retaining nut located on the outer/ upper face of the roof.
- Page 15 STEAM TEMPERATURE SENSOR This steam shower model is fi tted with a temperature sensor that monitors the internal cabin temperature. The temperature is selected on the control panel. When the internal cabin temperature reaches the predefi ned temperature it stops steam production until the temperature falls below, whereupon it re-activates the steam production again.
- Page 16 (image based on top cam fi tting) To fi t each of the cams, fi rst select the appropriate cam for the position on the door: 4 x Push button/Quick release for the lower position on the doors. 4 x Standard non push button for the upper position on doors. Position the Cam Body on the outside facing side of the door (curve pointing outwards).
-
Page 17: Fitting The Door Handles
FITTING THE DOOR HANDLES Each of the two shower doors requires a pair of chrome fi nished door handles to be fi tted. Each handle is comprised of several parts. Position the main handle part on the outside of a door ensuring the Chrome Washer and a Clear Washer are positioned also on the outside face over the thread. - Page 18 HAND SHOWER AND RISER You are now ready to assemble and connect the hand shower. The hand shower comprises of: Multi function hand shower Chr ome fi n ished riser bar Hand shower holster Chrome water hose Rear retaining nut Fitting screw The lower part of the riser bar has a threaded water connection.
- Page 19 GLASS SHELF Assemble the shelf fully before fi tting into the shower. Position the lower chrome rail over the holes in the glass on the underside of the shelf with the silver grommets positioned between the two. On the upper side of the glass, pass the bolt through a washer and through the hole in the glass and fasten into the end of the lower rail.
-
Page 20: Shower Valve
SHOWER VALVE The shower valve can be accessed from the rear of the shower and is located on the central tower. The valve is divided into three parts that are joined together. The uppermost part is the divertor. There are four connections able to be made here. - Page 21 SHOWER SEALS This shower comes with 2 fl apped shower seals and a pair of magnetic doors seals. FLAPPED SEALS These seals fi t over the long side of the shower doors on the opposite side to the fi tting of the handles. MAGNETIC SEALS The magnetic seals fi t onto the doors along the long edge of the glass door nearest the handles..
-
Page 22: Water Connections
Water Connections This product requires a hot and cold water supply. Your Hot and Cold water supply pipes should ideally be fi nished about 1 meter above the fl oor centrally in the corner and fi nished with 15mm compression isolating valvea. -
Page 26: Electrical Connections
Electrical Connections STEAM GENERATOR & ELECTRONIC CONTROL MAIN POWER This Steam Shower requires connections to MAINS UNIT This model has a separate Steam Generator ELECTRICITY. and Electronic Control Unit. Both parts have a Data Cable to provide electrical communication The Steam Generator is 3kw rated and the between each part and a Power transfer Whirlpool Bath uses a 1 Horse Power Pump. -
Page 27: Water Testing
Sealing the Shower OPTIONAL: Under normal use, the shower will return all water back into the tray. Should you choose, we recommend that you seal the shower internally with a good quality bathroom sealant to provide an extra level of water proofi ng. -
Page 28: Final Testing
Final Testing Check and test that each outlet function (hand shower, body jets and monsoon) work as expected by rotating the DIVERTOR DIAL (top chrome dial). Check the ON/OFF dial enables the water to be fully on or off in the position indicated on the valve markings. -
Page 29: Valve Operation
Valve Operation There are 3 control dials inside your Shower Cabin. These dials control the output functions, water fl ow and temperature of your shower. The top dial can be turned to allow you to choose which output you wish to use: Body Jets, Overhead (Monsoon) Shower and Hand Shower. -
Page 30: Electronic Control Panel
Electronic Control Panel Your steam shower is fitted with an electronic control panel that allows you to operate the electronic features of your shower. From the control panel you can control the lights, Steam, Radio and Bluetooth audio. Power ON / OFF In standby mode this button is lit Red. -
Page 31: Bluetooth Pairing
Bluetooth Pairing Before you can start streaming Audio to your 5: After a small amount of time you should see shower you must fi rst establish a connection the device name of the shower appear “ SPROUT”. between the shower and the device that will Select this to complete the Pairing of the two stream the audio to the shower;... - Page 32 Cleaning and third party product use DO NOT CLEAN BY SPRAYING THE HAND SHOWER DIRECTLY INTO AREAS THAT MAY PASS WATER - UNLESS YOU HAVE ADDED THE ADDITIONAL INTERNAL SILICONE IN PREVIOUS STEP This shower should be cleaned after every use to remove the build up of dirt and bacteria. We would recommend that after normal showering use, that the cabin doors are left open until the inside is fully dry.
- Page 33 Thermostatic Cartridge Your shower is fi tted with a Thermostatic Cartridge. Should you need to remove or replace the cartridge for maintenance or replacement, follow the instructions below. Q: I am having to turn the dial round as far as it will go to the hottest setting and the water is only just warm.
- Page 34 With the Chrome dial removed you will see a plastic ring covering with the Thermostat underneath. Note down the position the ring is placed in. Pull the plastic ring (Temperature safety lock) towards you to remove. Keep this part safe You will now see the head of the Thermostat clearly visible.
-
Page 35: For Technical Assistance
FOR TECHNICAL ASSISTANCE PLEASE CALL 01524 489939... - Page 36 This form must be filled out by the plumber/installer and electrician (where applicable) in order to validate the warranty. You are required to register the warranty online at www.vidalux.co.uk You MUST register the product warranty within 90 days following delivery...
Need help?
Do you have a question about the Lisbon Whirlpool Series and is the answer not in the manual?
Questions and answers