Page 1
Quick Start Guide Model: SW11/SW12/SW13 Series Version: 1.0 English Due to the regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the actual product and the written information in this manual.
Important Notes If you have any problems, please read this manual carefully or contact Customer Care. It's recommended that a qualified electrician perform the installation, especially if you are unsure about any parts of these instructions. 3. This product CAN NOT be used to replace the dimmer switch, 3-way switch or multi-way switch.
Page 3
9. The device can only connect to 2.4GHz Wi-Fi networks. Make sure that your phone is linked to the 2.4GHz network if you have a dual- band router with distinct 2.4GHz and 5GHz networks. 10. Make sure that the entered Wi-Fi password is correct when adding a new device.
Table of Contents Product Overview..................4 Installation....................5 Setup......................7 Connecting the Device to ZSmart App..............7 Connecting the Device to Amazon Alexa or Google Assistant......9 Product Features...................10...
Product Overview ON/OFF Button Status LED Indicator Neutral Wire Port Load Wire Port Line Wire Port Status LED Description: Rapid Blinking Green Slow Blinking Green In Pairing Mode (EZ Mode) In Pairing Mode (AP Mode) Solid Blue Solid Red Power On Power Off...
Installation Step 1: Remove the Existing Switch WARNING Risk of electric shock! Make sure the power to every switch has been turned off before installation. Turn off the power at circuit breaker or fuse box. Use an electrical tester to test the power is off before installation. 3.
Page 7
Wiring Diagram: LINE LINE LINE NEUTRAL NEUTRAL NEUTRAL 3. Carefully insert the main unit into the switch box, and mount it by the screws. 4. Finally, snap the faceplate onto the main unit. When the installation is completed, test each button to make sure the device is wired properly.
Setup Connecting the Device to ZSmart App Step 1: Download the App and Register Your Account Search for the ZSmart App in Apple App Store or Google Play Store and download the App to your mobile phone. Open the ZSmart App and log in with your account. If you do not have an account, create an account with your phone number or Email ID.
Page 9
Step 3: Add the Device to the App 1. Open the app, tap the "+" button on the top right corner of the interface, and then select the ”Add Device” option. Select the ”Electrical” option and then choose the corresponding model purchased. Enter the correct password for the Wi-Fi network you've selected.
Connecting the Device to Amazon Alexa or Google Assistant Tap on EDIT Button in the upper right corner of the device interface after successfully connecting the device to the ZSmart App. To link your ZSmart Account to Amazon Alexa or Google Assistant, select the Amazon Alexa or Google Assistant icon and follow the on-screen instructions.
Product Features Switch: From any location, turn on or off the device. Timer: Customize the schedule for the device to turn on or off automatically. Countdown: Af te r a s p e c i fi e d a m o u n t o f t i m e, t h e d e v i c e w i l l automatically turn on or off.
Guía Rápida Modelo: Serie SW11/SW12/SW13 Versión: 1.0 Español Debido a las actualizaciones periódicas de los sistemas y productos, ZKTeco no puede garantizar la consistencia exacta entre el producto real y la información escrita en este manual.
Notas Importantes Lea atentamente este manual o comuníquese con atención al cliente para cualquier consulta. Se recomienda que un electricista profesional realice la instalación, especialmente si no está seguro acerca de alguna parte de estas instrucciones. 3. Este producto NO PUEDE usarse para reemplazar el regulador de intensidad de luz, el interruptor de 3 vías o el interruptor de múltiples vías.
Page 14
8. El dispositivo está diseñado sólo para uso en interiores. 9. Este dispositivo sólo trabaja con redes Wi-Fi de 2.4GHz. Si tiene un enrutador doble banda con redes de 2.4 GHz y 5 GHz, asegúrese de que su teléfono esté conectado a la de 2.4 GHz. 10.
Page 15
Tabla de Contenidos Descripción del Producto................4 Instalación....................5 Con guración ..................7 Conexión del Equipo con la App ZSmart..............7 Conexión del Equipo con Amazon Alexa o Google Assistant......9 Características del Producto..............10...
Descripción del Producto Botón de Encendido /Apagado, Indicador LED Puerto de Cable Neutro Puerto de Cable de Línea Puerto de Cable de Carga LED Indicador de Estado: Parpadeo Rápido en Verde Parpadeo Lento en Verde En Modo de Emparejamiento En Modo de (Modo EZ) Emparejamiento (Modo AP) Azul Sólido...
Instalación Paso 1: Quite el Interruptor Existente ATENCIÓN ¡Riesgo de descargas eléctricas! Asegúrese de que todos los interruptores estén apagados antes de la instalación. Apague la alimentación en el disyuntor o en la caja de fusibles. Use un comprobador eléctrico para comprobar que la energía está apagada antes de la instalación.
Page 18
Paso 3: Instale el nuevo interruptor inteligente 1. Utilice un destornillador para separar la unidad principal (receptáculo) y la placa frontal. 2. Conecte los cables a los puertos correspondientes según el siguiente diagrama de cableado. Diagrama de Cableado: Línea Línea Línea Neutro Neutro...
Configuración Conexión del Equipo con la App ZSmart Paso 1: Descargue la App y Registre su Cuenta Busque la aplicación ZSmart en Apple App Store o Google Play Store y descargue la aplicación en su teléfono móvil. Abra la aplicación ZSmart e inicie sesión con su cuenta. Si no tiene una cuenta, cree una cuenta con su número de teléfono o correo electrónico.
Page 20
Paso 2: Encienda el Equipo Encienda la alimentación del dispositivo. Espere unos segundos hasta que el LED verde parpadea rápidamente, lo que significa que está en modo de emparejamiento. Nota: Si el dispositivo no comienza a parpadear en verde, presione y mantenga presionado cualquier botón por 5 segundos hasta que el LED comience a parpadear en verde.
4. Una vez que vea el mensaje “Se agregó con éxito" en la aplicación, puede editar el nombre del dispositivo manualmente. Toque el botón “Finalizado" para completar la configuración. Notas Importantes: El modo de emparejamiento predeterminado es el Modo EZ en la aplicación.
Después de completar la configuración, puede usar los comandos de voz admitidos que incluyen: Echo, enciende <nombre del dispositivo>. Echo, apaga <nombre del dispositivo>. Hey Google, enciende <nombre del dispositivo>. Hey Google, apaga <nombre del dispositivo>. Nota: Después de cambiar el nombre del dispositivo vinculado, actualice nuevamente la cuenta para actualizar el nombre.
Page 23
estado de ENCENDIDO y APAGADO automáticamente. Control de Grupo: Cree grupos para controlar múltiples dispositivos a la vez. Control por Voz: Use los comandos de voz para encender o apagar el dispositivo a través de Amazon Alexa y el Asistente de Google.
Page 24
Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the SW11 Series and is the answer not in the manual?
Questions and answers