Keurig K-Cup K150, COMMERCIAL Series Manual

Brewer Overview

Helpful Hints

1. Plug the brewer into its own grounded outlet.
   If the electric circuit is overloaded with other appliances, your brewer may not function properly. The brewer should be operated on its own circuit, separate from other appliances.
2. Keep your brewer turned "ON" at all times.
   To brew a fresh cup of coffee, tea, hot cocoa, or other beverage anytime you want, we suggest you keep your brewer turned "ON" all the time. However, the brewer is fully programmable so you can set it to turn on and off automatically to match your schedule. Or, if you prefer, set the brewer to automatically turn off after a period of time. Follow the simple instructions to make using the brewer convenient for you.
3. For the best tasting gourmet coffee, tea or hot cocoa, Keurig recommends using bottled or filtered water.
   Water quality varies from place to place. If you notice an undesirable taste in your cup of coffee, tea, hot cocoa, or other beverage (such as chlorine or other mineral tastes) we recommend you consider using bottled water or water from a filtration system. For best results, carefully follow manufacturer's instructions when using any water filtration system.
4. Customize Your Size, Flavor & Brew.
   With the choice of over 250 varieties of K-Cup^® pods and 5 brew sizes (4 oz., 6 oz., 8 oz., 10 oz., and 12 oz.) your Keurig^® brewer gives you endless options to customize the size, flavor, and brew that's perfect for you. For a strong, intense cup, select an Extra Bold K-Cup^® pod (with up to 30% more ground coffee than regular varieties) and brew the size that's right for you. The smaller the brew size, the more intense flavor in your cup. The larger the brew size, the less intense flavor in your cup.
5. Brewing into a travel mug.
   To brew into a travel mug, simply remove the Drip Tray Assembly and place the travel mug on the Drip Tray Base.
6. Descale the brewer regularly.
   Please refer to the nstructions.

Unpacking Your Brewer

1. Place the brewer box on a large steady surface (such as a table or countertop) or on the floor. Open the box.
2. Turn the box on its side with the front of the box face down.
3. Reach into the box and grasp the foam insert that contains the brewer.
4. Carefully pull the foam insert toward you and out of the box. The brewer will still be encased in the polyfoam and be on its side.
5. Remove the top polyfoam packaging material.
6. Carefully lift the brewer off of the bottom polyfoam and place it upright on a flat, steady surface.
7. Lift plastic bag off of the brewer.
8. Record the serial number for this brewer. The serial number can be found on the side of the brewer box or on the bottom of the brewer.
9. Place the brewer upright on a flat, steady surface. Remove tape holding Water Reservoir in place.

We recommend you save all packing materials in case future shipping of the product is necessary.

Keep all plastic bags away from children.

Features

K150 Brewer

1. Water Reservoir Lid
2. Water Reservoir
3. MAX FILL
4. Water Reservoir Lock Tab Slots
5. Handle
6. Funnel
7. K-Cup^® Pod Holder
   (F and G are the K-Cup Pod Holder Assembly)
8. K-Cup^® Pod Assembly Housing
9. Lid
10. Drip Tray Base
11. Drip Tray
12. Drip Tray Plate
13. LCD Screen
14. BREW Button
15. Housing
16. Power Switch
17. Power Cord
18. Removable Float
19. Removable Puncture Plate

Setup & First Brew

You cannot use your Keurig^® brewer until it has been set up for its first use.
NOTE: If the brewer has been exposed to temperatures below freezing, allow the brewer at least two hours to reach room temperature before brewing. A frozen or extremely cold brewer will not operate.

Setting up Your Brewer

1. Remove all pieces of packing tape from the brewer and Drip Tray. Remove the clear plastic film from the LCD Screen. Unwrap the Power Cord and plug the brewer into a grounded outlet.
2. Turn the brewer on, the Power Switch is located at the top left hand side of the brewer on the back. The brewer's LCD Screen will display the power up welcome screen.
   
3. Remove the Water Reservoir from the brewer by first removing the Water Reservoir Lid, then lifting the Water Reservoir straight up and away from the brewer (may be tight). Rinse with fresh water.
4. Fill the Water Reservoir to and not beyond the MAX FILL line with bottled or filtered water. Replace the Water Reservoir on the brewer making sure that the locking tabs engage with the brewer (fig. 2). Replace the Water Reservoir Lid on the Water Reservoir.
   
5. The brewer will automatically fill the internal water tank with water and then the water will be heated. This will take about 3 minutes. During the heating period, "HEATING PLEASE WAIT" will be displayed on the LCD Screen.
   
6. Place a 10 oz. mug on the Drip Tray Plate, then lift and lower the Handle. The BREW Button will now be illuminated. Press the BREW Button to start a cleansing brew.
   NOTE: A K-Cup^® pod should not be used for this sequence.
7. When the cleansing brew is complete, the brewer will go into its idle state and will be ready to brew your first K-Cup^® pod.

Ready to Brew Your First Cup

1. The LCD Screen will be in its idle state.
   
2. Lift the Handle. The K-Cup^® Pod Holder will open toward you.
   
3. Select a K-Cup^® pod.
   NOTE: Do not remove the foil lid or puncture the K-Cup^® pod.
4. Place a K-Cup^® pod in the K-Cup^® Pod Holder.
   
   
   There are two sharp needles that puncture the K-Cup^® pod, one above the K-Cup^® Pod Holder and the other in the bottom of the K-Cup^® Pod Holder. To avoid risk of injury, do not put your fingers in the K-Cup^® Pod Assembly Housing.
5. Lower the Handle to close the Lid over the K-Cup^® Pod Holder. (When it is closed completely, the BREW Button will flash up to 60 seconds.)
6. Place a mug on the Drip Tray Plate and select your brew size (fig. 7), then press BREW (fig. 8).
   
   
   NOTE: If you do not push the BREW Button in 60 seconds, the BREW Button will be disabled to prevent accidental activation. Re-activate the BREW Button by lifting and lowering the Handle completely.
7. There may be a short pause prior to coffee being dispensed. The entire brew process lasts for approximately 1 minute and ends with a burst of air to remove all liquid from the K-Cup^® pod.
   
   There is extremely hot water in the K-Cup^® Pod Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup^® Pod Assembly Housing during the brew process.
8. The end of brew is indicated by "KEURIG BREWED ENJOY."
9. Lift the Handle, remove and dispose of the used K-Cup^® pod.
   
   K-Cup^® pod will be hot.
10. Enjoy your first cup of Keurig HOT gourmet coffee, tea, hot cocoa, or other beverage!
    NOTE: After brewing a hot cocoa K-Cup^® pod, we recommend running a hot water brew cycle without a K-Cup^® pod.
11. Your brewer may display "HEATING PLEASE WAIT" as it heats water for the next brew cycle.

Stopping the Brew Process

If you need to stop the brewing after the process has started, press and release the Power Switch to turn the brewer 'OFF.' The flow of coffee, tea, hot cocoa, or other beverage will stop and the heating element and the LCD Screen will shut off.
NOTE: You may get less coffee, tea, hot cocoa, or other beverage in your cup during your next brew. We recommend that you perform a cleansing brew with water only after a terminated brew. Then your next brew will be the volume you have selected.

Adding Water

The LCD Screen will indicate when the water level in the Water Reservoir is low or if the Water Reservoir has been removed by displaying the words "FILL WATER RESERVOIR".

The brewer will not allow you to brew when "FILL WATER RESERVOIR" is displayed (fig. 9).
The Water Reservoir can be filled in three ways.

1. Remove the Water Reservoir from the brewer by first removing the Water Reservoir Lid from the Water Reservoir, then lifting the Water Reservoir straight up and away from the brewer. Fill with water to and not beyond the MAX FILL line. Place the Water Reservoir back on the brewer and replace the Water Reservoir Lid.
   
   Do not remove the Water Reservoir during the brewing process.
2. Lift the Water Reservoir Lid and pour water directly into the Water Reservoir while it is still attached to the brewer, then replace the Water Reservoir Lid.
3. The brewer can also be connected directly into the water line. To order a K150 Direct Plumb Kit (#40559) please call 1.888.CUP.BREW (287.2739) or contact your Keurig Authorized Distributor.

Brewing Iced Beverages

Your iced tea and iced coffee taste best when fresh-brewed hot over ice.

1. Fill a 16 oz. mug (do not use glass) to the top with ice and place a K-Cup^® pod into your brewer.
2. Select your brew size, we recommend selecting a 6 oz. or 8 oz. brew. Press the BREW Button.
3. Stir and enjoy!

Do not brew into a cup made of glass. Doing so may cause the glass to crack or break.

Brewing Hot Water

Your brewer is able to produce hot water for use in cooking, making soups, oatmeal, etc. Simply lift and lower the Handle on the brewer without adding a K-Cup^® pod. The blue BREW Button will flash. Be sure to have a mug on the Drip Tray Plate and then press the BREW Button.

Menu Controls & Indicators

Menu controls

To enter the Menu Mode the brewer should be plugged in and the power must be off. Press and hold your finger on the display for about 10 seconds while pressing and releasing the Power Switch (fig. 10). Once the Menu Screen appears (fig. 11) remove your finger.

Press any line item to enter the set up for that particular feature. Please reference the Menu Navigation.
If you are experiencing any problems with your brewer, please contact your Keurig Authorized Distributor.

Menu Mode Navigation

Home
Press "HOME" at any time to return your brewer to an idle state.

Clock
Setting the clock is optional. To set the clock.

Brew Temp
The brew temperature is pre-set at 193˚F. You do not have to program the brew temperature but you can adjust it up or down by 5˚.

Brew Size(s)
Five brew sizes are available: 4 oz., 6 oz., 8 oz., 10 oz., and 12 oz. See "Programming Brew Size".

Auto OFF
Auto Off allows you to program your brewer to automatically turn off two hours after the last brew. See "Programming On/Off Features".

ON/OFF Time
You can leave your brewer on all the time and use the Power Switch to turn it off. Or you can program the brewer to automatically turn on or off at a specific time.

Language
This brewer is shipped with English as the default language. See "Language Settings".

Contact
The contact setting features allows you to program the contact information you need for brewer support and help. See "contact Screen Settings".

Setting the clock

Setting the clock is optional. When the clock is set, the time will appear on the LCD Home Screen.
NOTE: You must set the clock if you will be programming the Auto On/Off Time feature.

1. From the Menu Mode, press "CLOCK."
2. The set clock screen will display "DISABLED" if the brewer is new or if electrical power has been interrupted. Press "DISABLED" to set a time. Press "H" repeatedly to advance the hour in steps or hold it down to scroll through the hours quickly. When you have set the hour then press the "M" to set the minutes, press repeatedly to advance by a minute each time or keep it pressed to scroll quickly.
   
3. Press "OK" when you are finished. The clock is now set.
4. The correct time should now be displayed on the LCD Home Screen.

NOTE: If power is interrupted to the brewer, follow the procedure above to reset the time as the clock will not be visible. Brew size and brew temperature menu settings will be restored automatically. All other settings will be restored automatically after clock is set.
NOTE: To disable the clock, press the time. However, the 'On/Off' time setting will also be disabled.

Programming Brew Temperature

(188° – 198°F)
The brewer brews at a preset temperature of 193˚F. You can adjust this temperature up or down by 5˚. Simply follow the instructions below.

1. From the Menu Mode, press "BREW TEMP."
2. The LCD Screen will now display the Brew Temperature programming options (fig. 13). The temperature 193˚F (initial setting) will be displayed at the top of the LCD Screen to indicate the current temperature setting.
   
3. Press the + symbol to increase the temperature and the – symbol to lower the temperature one degree at a time.
4. Once you have reached your desired brew temperature, press "OK." The brew temperature is now programmed.
   NOTE: At high altitudes (over 5,000 feet) if boiling occurs, use the temperature adjustment (-5°) to lower the temperature.

Programming Your Brew Size

All brew sizes are enabled in the default setting. If you want to disable any brew size, just press on the appropriate icon(s). Please follow instructions outlined below.

1. From the Menu Mode, press "SET BREW SIZE(S)."
2. The LCD Screen will display all enabled brew sizes. To disable a brew size press the icon. The check mark will change to an "X" indicating that the brew size is disabled (fig. 14). To enable a disabled size, press it again.
   
3. Once you have selected your desired brew size(s), press "OK." The brew size(s) are now programmed.
   NOTE: You can not delete all brew sizes. To enable a brew size you have already disabled, just press its icon and then press "OK." The 8 oz. setting is the default brew size if all sizes have been disabled.

Programming on/off Features

The brewer provides three modes so that you can enjoy gourmet coffee, tea, hot cocoa, or other beverage on your own schedule.

1. Leave the brewer "ON" all the time. The brewer can be left on all the time so that it is always ready to brew a fresh cup of gourmet coffee, tea, hot cocoa, or other beverage. To turn the brewer off at any time, simply press and release the Power Switch. Press and release the Power Switch again to restore power to the brewer. You will have to wait for the water to heat up before the brewer is ready to brew.
2. Program the brewer to "AUTO OFF." The brewer can be programed to automatically turn off 2 hours after the last brew.
   
   1. From the Menu Mode, press "AUTO OFF." The LCD Screen will now display the "AUTO OFF" programming option.
   2. To enable the "AUTO OFF" feature, press "ON." "ENABLED" will appear on the screen and press "OK." To disable the "AUTO OFF" feature, press "OFF." "DISABLED" will appear on the screen and press "OK."
3. Program the brewer for a specific On/Off Time.
   NOTE: To use this programming feature, the clock must be set to the correct time.
   1. After setting the correct time (refer to "Setting The Clock"), return to the Menu Mode and press "ON/OFF TIME."
   2. To set the ON time, press "DISABLED." The display will change to a time of day. Press "H" to set the hours and "M" to set the minutes. Once the desired time is set, press "OK" to accept this time.
   3. To set the OFF time, press "DISABLED." The display will change to a time of day. Press "H" to set the hours and "M" to set the minutes. Once the desired time is set, press "OK" to accept this time.
      

Language Settings

The brewer is shipped with English as the default language. To change the default to Français or Español, follow the instructions outlined below.

Set Language

1. From the Menu Mode, press "LANGUAGE."
2. The LCD Screen will now display the Language setting options.
   
3. Press the desired Language button, then press "OK" to confirm your selection.

Contact Screen Settings

The contact screen is pre-programmed with the following information: Keurig Green Mountain, Inc. and www.Keurig.com.
You can reprogram the brewer with your contact information. The contact screen will appear in the screen saver.

1. From the Menu Mode, press "CONTACT." The LCD Screen will display the Keurig default contact information.
   
2. Press the Upper (Company Name) Box. The Keypad will appear along with the current information.
   
   NOTE: Unless changed by the user, Keurig contact information will be present on the screen.
   1. Press the Delete Key repeatedly to remove current information. Enter new information using the Keypad.
      NOTE: To select Upper Case, Lower Case, Numerals, Upper Case Accents, Lower Case Accents, press the Keypad Change Key located at the bottom center of the screen.
   2. Press "OK" to save your changes and return to the Main Contact Screen.
      NOTE: Pressing the Back Arrow Key will return to the Main Contact Screen without saving changes.
3. Press the Middle (Phone Number) Box. The Numeral Keypad Mode will appear along with the current information.
   
   1. Delete current phone number, if any, and enter new information using the Keypad.
   2. Press "OK" to save your changes and return to the Main Contact Screen.
4. Press the Lower Box. This box can be customized to contain any information such as web/email address, contact name, etc.
   
   1. Delete or enter new information using the Keypad.
   2. Press "OK" to save your changes and return to the Main Contact Screen.
   3. In the Main Contact Screen (fig. 18), press "OK" to save the updated screen as the default and return to the Menu Screen.

The brewer is now fully programmed. Press "HOME" on the Menu Screen to return your brewer to its idle state.

Cleaning & Maintenance

Cleaning External Parts

Regular cleaning of the brewer's external components is recommended.
The following section provides instruction for standard cleaning procedures. For in-depth NSF certified instructions, please refer to the Cleaning and Sanitization Guide.

1. Never immerse the brewer in water or other liquids. The Housing and other external components may be cleaned with a damp, soapy, lint-free, non-abrasive cloth.
2. The Drip Tray can accumulate up to 12 oz. of overflow. The Drip Tray and Drip Tray Plate should be periodically inspected and rinsed clean. To remove the Drip Tray Assembly, simply slide it toward you, keeping it level at all times to avoid spilling. The Drip Tray and Drip Tray Plate should not be placed in the dishwasher. They should be cleaned with a damp, soapy, lint-free, non-abrasive cloth and rinsed thoroughly.

Cleaning the K-cup^® Pod Holder Assembly

1. Cleaning the Parts — The K-Cup^® Pod Holder Assembly can be placed onto the top shelf of a dishwasher.
   NOTE: Use low temperature cycles in the dishwasher.
   To remove the K-Cup^® Pod Holder Assembly from the brewer, open the cover by lifting the Handle.
   Grasp the top of the K-Cup^® Pod Holder with one hand while pushing up on the bottom of the K-Cup^® Pod Holder from underneath with the other until it releases (fig. 22). After cleaning, align the K-Cup^® Pod Holder with the opening using the two front ribs as a guide, and snap them into place from the top.
   
2. Cleaning the Funnel — The Funnel can be removed from the K-Cup^® Pod Holder by pulling on it until it pops off (fig. 23). The Funnel is dishwasher safe. To replace it, just snap it back onto the K-Cup^® Pod Holder.
   
3. Cleaning the Exit Needle — The exit needle is located on the inside bottom of the K-Cup^® Pod Holder Assembly. Should a clog arise due to coffee grounds, it can be cleaned using a paper clip or similar tool. Remove the K-Cup^® Pod Holder Assembly and detach the Funnel. Insert the paper clip (as shown in fig. 23) into the exit needle to loosen the clog, then flush with fresh water. The K-Cup^® Pod Holder Assembly can be placed onto the top shelf of a dishwasher.
   NOTE: Use low temperature cycles in the dishwasher.
4. Cleaning the Puncture Plate — The Puncture Plate can be removed by grasping the finger grips of either side and pulling forward (fig. 24). Once removed, spray the Puncture Plate with detergent, brush clean and rinse if necessary. Be sure to replace the Puncture Plate after cleaning to ensure proper brewer operation.
   

There are sharp needles that puncture the K-Cup^® pod above the K-Cup^® Pod Holder and in the bottom of the K-Cup^® Pod Holder. To avoid risk of injury, do not put your fingers in the K-Cup^® Pod Assembly Housing.

Cleaning the Water Reservoir & Water Reservoir Lid

The Water Reservoir or Water Reservoir Lid should not be put into the dishwasher. They should be cleaned with a damp, soapy, lint-free, non-abrasive cloth and rinsed thoroughly. Do not dry the inside of the Water Reservoir with a cloth as lint may remain.

Please rinse the Water Reservoir thoroughly after cleaning to ensure that no cleaners or cleaning solutions remain in this area as they may contaminate the water supply in the brewer.

Descaling Your Brewer

Depending on the mineral content of your water, calcium deposits or scale may build up in your brewer. Scale is non-toxic but if left unattended can hinder brewer performance. Regularly descaling your brewer every 3 to 6 months helps maintain the heating element, and other internal parts that come in contact with water. Calcium deposits may build up faster, making it necessary to descale more often.
Before you begin, you will need a large ceramic mug, fresh water,
Keurig^™ Descaling Solution, and access to a sink. Do not use a paper cup.
Properly follow the descaling procedure.

Descaling Procedure

Empty the water from the Water Reservoir. If there is a Keurig^™ Water Filter, remove and set aside. Disable Auto Off features for your brewer.

1. FIRST DESCALING SOLUTION RINSE
   • Press the Power Switch to power the brewer off.
   • Pour the entire bottle of Keurig™ Descaling Solution into the Water Reservoir. Then fill the empty bottle with bottled or filtered water and pour into the Water Reservoir. Press the Power Switch to turn the brewer back on.
   • Place a large mug on the Drip Tray Plate and run a cleansing brew using the largest brew size. Do not add a K-Cup^® pod. Pour the contents of the mug into the sink.
2. SECOND DESCALING SOLUTION RINSE
   • Repeat the brew process without a K-Cup^® pod, until "ADD WATER" is indicated. Let the brewer stand for at least 30 minutes while still on.
   • After 30 minutes, discard any residual solution, and rinse the Water Reservoir thoroughly.
3. FRESH WATER RINSE
   • Ensure the Water Reservoir is filled with fresh water.
   • Place a large mug on the Drip Tray Plate and run a cleansing brew using the largest brew size. Do not add a K-Cup^® pod. Pour the contents of the mug into the sink.

NOTE: The cleaning action of Keurig^™ Descaling Solution may result in a foam dispensed from the brewer. This is natural, as the solution is reacting with the scale inside. For a brewer that is heavily scaled, the brewer may not fill properly after the descaler is added. If this occurs, you may see only a small or no output dispensed followed by the sound of air blowing out. If this occurs:

• Turn off and unplug the brewer.
• If there is Keurig™ Descaling Solution in the Water Reservoir, discard the contents, rinse the Water Reservoir thoroughly and refill with water.
• Plug the brewer back in, power on, and repeat the Step 3 Fresh Water Rinse cycle. The brewer should begin to function normally as the solution is rinsed out and the scale is removed. If problem persists, allow the brewer to sit unplugged for at least 30 minutes before continuing with the rinse.

For further descale information please contact your Keurig Authorized Distributor.

Service

Beyond these recommended cleaning and maintenance procedures this brewer is not user serviceable. For service, please refer to the Warranty section of this guide.

Purging the Brewer

If your brewer has not been used for more than one week, you should purge the water from the internal water tank.

1. If there is water in the Water Reservoir, remove the Water Reservoir Lid, then lift the Water Reservoir straight up and away from the brewer.
   Discard water, rinse and refill with water. Place the Water Reservoir back on the brewer and replace the Water Reservoir Lid. (If there is no water in the Water Reservoir, simply refill.)
2. Be sure the brewer is turned 'ON.' Lift and lower the Handle on the brewer without inserting a K-Cup^® pod.
3. The LCD Screen will be in its idle state (fig. 4).
4. Place a large mug on the Drip Tray Plate and select Large Mug (10 oz. serving) brew size from the Select Brew Size Menu.
   
5. Discard water.
6. Repeat steps 2 – 5 two more times to completely purge water from the internal water tank.

Draining the Brewer

1. Turn off the brewer, unplug it, and allow the brewer to cool approximately 30 minutes.
2. Empty the Water Reservoir by first removing the Water Reservoir Lid from the Water Reservoir then lifting the Water Reservoir straight up and away from brewer (may be tight). Rinse and empty the Water Reservoir.
3. Turn the brewer around so the back is facing out. Unscrew the small knob to release the back panel, remove the panel from the brewer, and set it aside. If the screw is tight, you may need to use a flathead screw driver. Pull the hot water tube downward until the end is free (fig. 26). Over a large pitcher, remove the plug and drain the water from the internal water tank into the pitcher.
   
   
   If the brewer was not allowed to cool sufficiently, the water draining from the tube may be very hot. Recap the tube.
   NOTE: To avoid losing parts, when finished, re-insert the tube and screw the panel back onto the brewer.
   If you need assistance with your brewer, please contact your Keurig Authorized Distributor.

Storage

Drain the internal water tank before storing and ensure that you store your brewer in a safe and frost free environment. It is suggested to store your brewer in the upright position. If you store the brewer in a cold environment, you run the risk of water freezing inside the brewer and causing damage. When you prepare to use it after storage, we recommend running three cleansing brews without a K-Cup^® pod. If you plan to move your brewer to a different location, turn the brewer off, unplug it and empty the internal water tank. If your brewer has been in an environment below freezing, please be sure to let it warm to room temperature for two hours before using.

Troubleshooting

If any problems persist, contact your Keurig Authorized Distributor.

IMPORTANT SAFEGUARDS

Safe Operation & Use
When using electrical appliances, basic safety precautions should be followed, including the following:

1. Read all instructions before using.
2. Do not touch hot surfaces. Use handles and knobs when available.
3. This appliance must be properly installed and located in accordance with these instructions before it is used.
4. The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electrical shock, or injury to persons.
5. Do not place on or near a hot gas or electric burner, or in a heated oven.
6. Do not use outdoors.
7. To protect against fire, electric shock, and injury do not immerse cords, plugs, or the appliance in water or any other liquid.
8. Fill the Water Reservoir up to and not beyond the MAX FILL line.
9. Use only water in this appliance! Do not put any other liquids or foods in the Water Reservoir except as instructed in the Cleaning Instructions in this guide.
10. Turn off and unplug the brewer before cleaning or maintenance. Allow to cool before putting on or taking off parts and before cleaning the appliance.
11. For best operation, plug the appliance into its own electrical outlet on a dedicated circuit to prevent flickering of lights, blowing of fuses, or tripping a circuit breaker.
12. Do not operate any appliance with a damaged Power Cord or plug or after the appliance malfunctions or is damaged in any manner. Contact your Keurig Authorized Distributor to report any malfunction of or damage to the brewer.
13. Do not let the cord hang over the edge of the table or counter, or touch hot surfaces.
14. To disconnect, press the Power Switch on the brewer to "OFF" status and then remove the plug from the wall outlet.
15. Close supervision is necessary when any appliance is used by or near children.
16. Do not lift the Handle while brewing is in progress.
17. Always keep the Water Reservoir Lid on the Water Reservoir unless you are refilling it.
18. This appliance is equipped with a Power Cord having a grounding wire with a grounding plug. The appliance must be grounded using a 3-hole properly grounded outlet. In the event of an electrical short circuit, grounding reduces the risk of electrical shock.
19. If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
20. Do not, under any circumstances, cut or remove the third (ground) prong from the Power Cord or use an adapter.
21. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.
22. Do not use the appliance for other than its intended use.
23. The Water Filter Starter Kit (GTIN 649645050720) and cartridges (GTIN 649645050737) are compatible with the K155 brewing system, but are not certified by NSF. The use of these accessories will void the certification of NSF.
24. Always brew with the Removable Puncture Plate (item S) installed. Failure to do so will result in a failure to properly brew.

TO USERS AND PARENTS

1. DO NOT permit children to use brewer unless there is adult supervision. Brewer dispenses very hot water.
2. SPECIAL NOTICE FOR HOT COCOA USERS: IMMEDIATELY AFTER USING A HOT COCOA K-CUP^® POD, RUN a Hot Water Brew Cycle without a K-Cup^® pod to avoid the possibility of clogging the exit needle. DO NOT assume the next user will do this.

There are two sharp needles that puncture the K-Cup^® pod, one above the K-Cup^® Pod Holder and the other in the bottom of the K-Cup^® Pod Holder. To avoid risk of injury, do not put your fingers in the K-Cup^® Pod Assembly Housing.

There is extremely hot water in the K-Cup^® Pod Holder during the brew process. To avoid risk of injury, do not lift the Handle or open the K-Cup^® Pod Assembly Housing during the brewing process.

Please always keep the brewer in its upright position to avoid potential injury and/or damage to your brewer.

SHORT CORD INSTRUCTIONS: A short power supply cord is provided to reduce the risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used,

1. the marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance;
2. the cord should be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally; and
3. the extension cord must include a 3-prong grounding plug.

THIS PRODUCT IS FOR COMMERCIAL USE ONLY.

RISK OF FIRE OR ELECTRIC SHOCK
DO NOT OPEN

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE THE BOTTOM COVER. NO USER SERVICEABLE PARTS ARE INSIDE. REPAIR SHOULD BE DONE BY AUTHORIZED SERVICE PERSONNEL ONLY.