Summary of Contents for WOHLHAUPTER 3E TECH+
- Page 1 536015 Bedienungsanleitung Digitalanzeige TECH+ Operating Manual Digital Readout Module TECH+ www.wohlhaupter.com...
- Page 2 If possible, please remove old batteries or accumulators as well as old lights from the equipment without damaging or destroying the device and dispose of those parts separately. You‘re responsible to erasing private data potentially stored on equipment before disposing of it. 2 www.wohlhaupter.com...
- Page 3 In dieser Anleitung wird in den Darstellungen die metrische Version dargestellt. Umstellung mm/inch siehe Nr. 4. The 3E digital readout module (536015) is adjustable TECH+ in metric and inch. Metric version pictured throughout. Conversion mm/inch see No. 4. 3 www.wohlhaupter.com...
- Page 4 ON/RESET Push “ON / RESET“ Connect Alternativ 1.2.1 1.3.1 Push “ON“ – Connect Push “RESET“ 4 www.wohlhaupter.com...
- Page 5 • Clip on readout module: The last displayed measured value appears on the display again. • 2nd hold for 2 seconds = “RESET“: Display indication “0.“ • Automatic switch-off 30 seconds after completing the adjustment process. • Maximum display time 120 seconds. 5 www.wohlhaupter.com...
-
Page 6: Diameter Adjustment
Diameter Adjustment max. 360° Push “ON / RESET“ – Digitalanzeige TECH+ abnehmen Detach 3E TECH+ readout module Ohne Vorzeichen = Durchmesservergrößerung Minus Vorzeichen (-) = Durchmesserverkleinerung No preceding sign = diameter increase Negative preceding sign (-) = diameter reduction 6 www.wohlhaupter.com... - Page 7 Das Display zeigt immer das Differenzmaß zum vorher eingestellten Wert bzw. zu “0“! Die absolute Schieber- stellung kann nicht angezeigt werden! The display always shows the difference from the previ- ously set value or the difference from “0.” The absolute slider position cannot be displayed. 7 www.wohlhaupter.com...
- Page 8 If the spindle is started with the unit still attached, the display unit drops off. For reliable operation, the coupling position must be kept clean at all times. In the event of any impairments or noticeable problems, the display unit should not be used. 8 www.wohlhaupter.com...
-
Page 9: Description Of The Display
Beschreibung Display Description of the display ① – ② ③ ① Akkuladezustand wird angezeigt ② Vorzeichen – (Minus) ③ Anzeige-Einheit metrisch [mm]/imperial [inch] ① Battery charge level is displayed. ② Prefix – (minus). ③ Displayed unit metric [mm]/imperial [inch]. 9 www.wohlhaupter.com... - Page 10 • Select mm or inch. Push and hold the “ON/RESET” button for 2 seconds to confirm selection. • Select one of the three color patterns. Push and hold the “ON/RESET” button for 2 seconds to confirm selection. Push “ON / RESET“ 10 www.wohlhaupter.com...
- Page 11 • Batterie Symbol mit 0% blinkt → Akku laden, weiterarbeiten nicht möglich • Battery life: approx. 4 hours. • Battery level <10 % →. Battery symbol is flashing. • Battery symbol with 0% flashing →. Charge module, further work not possible. ② ① 11 www.wohlhaupter.com...
-
Page 12: Technical Data
• Digital display resolution: 0.001 mm (.00005") in dia. • Storage temperature: -10°C to +65°C (14°F to 104°F). • Operating temperature: +10°C to +40°C (50°F to 104°F). • Battery: 3.7 V, 150 mAh, Li-Ion. • Battery replaceable at the factory. 12 www.wohlhaupter.com... - Page 13 A154. In road and maritime transport, it is possible according to SV 376 (training certificate required). Zubehör (Bild 5.1) Spare parts (Pic. 5.1) 536016 Ladestation inkl. USB-C-Kabel Docking station includes USB-C cable 13 www.wohlhaupter.com...
-
Page 14: Fehlerbehebung
Display Possible Solution reasons Display unit and Connect display - .- - - tool not connected with tool, check coupling and contact points and clean if necessary Short circuit at Clean contact Error the contact point points Contact 14 www.wohlhaupter.com... -
Page 15: Wartung
Only leave the module on the docking station during the charging process. Do not use the connected docking station for storage. Die Digitalanzeige darf NICHT in Werkzeug-Reinigungsanlagen gereinigt werden! Do NOT clean the 3E digital readout TECH+ module in tool cleaning systems! 15 www.wohlhaupter.com... - Page 16 Maybachstraße 4 · 72636 Frickenhausen Postfach 1264 · 72633 Frickenhausen Tel. +49 (0)7022 408-0 · info@wohlhaupter.com WEEE-Reg.-Nr. DE 15820388 Copyright © 2025 Wohlhaupter GmbH – Alle Rechte und technische Änderungen vorbehalten. · All rights and technical changes reserved. 102605/01.2025 www.wohlhaupter.com...
Need help?
Do you have a question about the 3E TECH+ and is the answer not in the manual?
Questions and answers