Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Storage 4 Crafts Putsborough
- Page 1 Putsborough away Assembly Instructions revised 0425 - 1.0...
- Page 2 It is strongly recommended to have two persons present when assembling this item. We advise that you unpack the boxes in the order shown in these instructions and follow the assembly instructions carefully. Please be careful during construction as section of the cupboard may be unstable until construction is complete.
- Page 3 Your hardware pack should contain the following: CODE DESCRIPTION QTY PICTURE Connnecting Bolt Connecting Lock Mini Connecting Bolt Shelf Peg (lock) HANDLE2 Bow Handle Handle Screw Desk Hinge 35-15S Screw Castor Black Castor Black with Brake 35-17S Caster Screw Leg Caster Axi Hinge Two AXI-HINGE Part...
- Page 4 STEP 1 SA-PUTS-BOX1 You will need to open box - Insert CL1 Locks into the holes as indicated with a blue circle screw in to this point Screw CB1 Bolts into all the holes marked with a red circle Screw CB1 Bolts into all the holes marked with...
- Page 5 STEP 2 SA-PUTS-BOX2 You will need to open box - SA-WOOL-BASE Insert CL1 Locks into the holes as indicated with a blue circle Front Edge Attach castors with brakes C3 with screws 35-17S as shown to holes marked with green circles Attach castors C2 with screws 35-17S as shown to holes marked with red circles...
- Page 6 STEP 3 SA-PUTS-BOX3 You will need to open box - Insert CL1 Locks into the holes as indicated with a blue circle SA-PUTS-MB1...
- Page 7 STEP 4 Attach the Base to the left hand side by slotting the panel onto the connecting bolts and tightening the connecting locks in the base. Then secure the base to the sides using the angle brackets you have already attached to the sides (using screws 35-17S). Then x the two MB1 backs and the MB2 backs to the left hand side as shown below.
- Page 8 STEP 5 Attach the SA-PUTS-RHS to the section you have already constructed, tighten all of the connecting locks and secure the base to the right hand side with the angle brackets as in step 4.
- Page 9 STEP 6 Attach the SA-PUTS-DSH to the section you have already constructed. Secure the mini connecting locks (which are pre tted into the DSH panel) to the left and right hand sides by turning the mini connecting locks.
- Page 10 STEP 7 Attach the SA-PUTS-TOP to the the section you have already constructed as shown below. Screw CB1 connecting bolts into the six holes in TOP panel and then secure with CL1 connecting locks in the SA-WOOL-TCD and the left and right hand sides. SA-PUTS-TOP...
- Page 11 STEP 8 Take your door and insert caster C5 into the pre tted bracket on the bottom of each door. Fit the handle using the screws provided. To t the door insert the cup of the Axi Hinge that you have pre tted to the side into the cut out on the door panel and then secure each hinge with 2 x 35-15S Screws.
- Page 12 STEP 9 Position your door so that it is open no more than 90 degrees so that they will support you desk panel. Attach hinges H3 using screws 35-15S to the desk shelf (DSH). Then place the desk on top of the doors and attach the hinges to the desk panel. To close the desk and secure it fold the desk into the closed postion and turn the key in the lock to secure the desk.
- Page 13 STEP 8 SA-PUTS-BOX4 You will need to open box - Below you will see the placement for all for all of the shelves, boxes and trays. To t the shelves insert shelf pegs SP3 into the holes for each shelf. Ensure that the at surface of the peg is facing up.
-
Page 14: Important Safety Information
IMPORTANT SAFETY INFORMATION When the desk is in use always ensure it is fully supported on the doors - they must be open no more than 90 degrees. When the desk is closed always ensure the lock is fully engaged FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DAMAGE TO YOUR UNIT AND /OR INJURY...
Need help?
Do you have a question about the Putsborough and is the answer not in the manual?
Questions and answers