Coaster 900721 Assembly Instructions Manual

900721 900721 900721 900721 900721 900721 900721 900721 900721 900721 900721
ITEM: ITEM: ITEM: ITEM: ITEM: ITEM: ITEM: ITEM: ITEM: ITEM: ITEM:
STEP 4-1
STEP 10
STEP 7-1
Operating the clocks as following pictures.
Your clock is fitted with a Westminster Chiming movement. This has an automatic night silence function that silences the
1.Solution for not reporting the time with chime: the hour is signaled, otherwise , repeat the same procedure again. It can be repeated
NOTES: PLEASE MAKE SURE CLOCK IS IN LEVEL POSITION, OTHERWISE
Chimes between 10.00 P.M. and 5.00 A.M.(last strike 9:00PM, first strike 6:00AM).
Regarding the timekeeping and pendulum troubleshooting methods:
a.Rotate the volume button (Figure 2 VOLUME) to the maximum position. several times to achieve the best results. Finally put back the seconds cap.
IT WILL NOT OPERATE PROPERLY.
* DON'T PUT BATTERIES INTO THE MOVEMENT BEHIND OF PENDULUM DRIVER.
Before the clock leaves the factory, the clock has been set at 5:55AM.
Do not mix Old and New batteries. Do not mix Alkaline, and Standard(Carbon - Zinc) or
Please make sure you have 2 x D Alkaline batteries, as these are not included. You will also need a screwdriver.
b.Check whether the positive and negative positions of the battery are correct (Figure 1). If it (Note: Keep the two clock hands in parallel position, and they cannot touch each other,
STEP 1-1
■The time cannot be adjusted by adjusting the hour hand (short hand), please turn the
Rechargeable(Nickel - Cadmium) batteries.
ALKALINE BATTERIES REQUIRED
is inaccurate, please reinstall it according to the icon. neither can touch the face of the clock, nor touch the glass of the front clock)
minute hand (long hand) clockwise.
1.TO START THE CLOCK
c.If the positive and negative poles of the battery are correct and the problem is still not  Solution 2： Set the time to the time when you hear the time signal, immediately
Lift the up-cover from the back of the top unit(A), you will find a battery holder. Open the
resolved, adjust the time to 5:55 clockwise using the minute hand, remove the battery, remove the battery, remove the second cap, remove the minute hand, and re-set the
(Note: Turn the minute hand counterclockwise, and cannot go past the 12 o'clock position,
ASSEMBLY TIPS:
battery cover, insert 2 new 1.5 volt "D" alkaline batteries into the Battery Holder and making
Here are a few symptoms that are associated with 'Defective Batteries' or 'Incorrect Installation'
wait for a while, and place it again. Then adjust the minute hand to 6:00 to tell the time minute hand to the 12 o'clock position, and set the clock to 5:55. position, replace the
otherwise it will damage the timekeeping contacts of the movement, resulting in failures
1. Remove hardware from box and sort by size.
sure the battery is as indicated(picture 1). Push the bob of pendulum(H) leftwards to let the
and do not indicate that the clock itself is defective:
and music. battery. Automatically or manually dial to 6:00, the hour hand tells the time for 6:00AM.
2. Please check to see that all hardware and parts are present prior to start of assembly.
BACK OF THE CLOCK
such as no timekeeping or no music.)
clock run(picture 3).
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
d.Or use the TIME ADJ button on the battery box (Figure 2) to solve problem (c.) above, each Then manually adjust to the actual local time, and then install the seconds cap.
Warning!
Problem
ｈｏｌｅ
2.TO SET TIME:
■Before the clock leaves the factory, the clock hands have been set at 5:55AM. If the clock 9.If the battery is insufficient, please replace the battery in time. time you press, no more than 8 times, you can hear the time and music. The time signaling 1. Don't attempt to repair or modify patrs that are broken or defective. Please contact the store immediatelly.
Your clock strikes six(6) times on every hour.
time is obtained on the dial. Do not push too hard or turn the hand counter clockwise (never
2.This product is for home use only and not intended for commercial establishments.
Solution
(Note: If the positive and negative poles of any battery are reversed, they must be removed display is not this time, please turn the minute hand clockwise to adjust to 5:55AM, and then this time is 6:00 AM. Then use the minute hand to adjust the hour hand clockwise to the
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
turn the short hand), otherwise it will cause damage of movement(picture 4).
Change the chime section batteries, and set time and chime again by following "SETTING TIME AND
first and then installed again. All are taken down to initialize the clock. Then install it insert the battery. actual local time.
CHIME"procedure.
3. TO ADJUST MELODY SELECTION:
STEP 5
2.When there is no music when telling the time, push the sliding button of MELODY SELECT correctly. It is not possible to mix an old battery with a new battery, let alone replace it with
short chain
have the striking sound every hour. The button in position( ): this selection will have both
STEP 8
■The first chime is set to 6:00 AM. The chime will stop automatically from 10:00 PM to 5:00 AM.
STEP 2-1
Problem another type of battery. Be sure to use a large battery of the same model size D. A bad (Figure 2) to the middle position( ).
long chain
the striking sound and Westminster chime every hour. The button in position( ): this
(The night stop function is programmed before leaving the factory. The user cannot change
Your clock starts to chime erratically on every hour.
3.If there is music without telling the time, push the sliding button of MELODY SELECT (Figure battery can also cause the clock to work infrequently.)
selection will only have the Westminster chime every hour. The clock will not sound from
Solution
it)
10.Possible conditions of the clock caused by insufficient battery power: Inaccurate time 2) to the middle position( ).
PART NAME
FURNITURE TIPPING RESTRAINT
Press the "Set" Button of TIME ADJ, the clock will chime, and increase one chime per push, push to
10:00 pm to 5:00 am(picture 2).
4.The time telling time is inconsistent with the displayed time. It can be adjusted by the TIME reporting, random time reporting, always reporting one time. Or the volume of timekeeping
the correct chime.
4.TO ADJUST TIME:
■Once the battery is removed, the movement will be automatically initialized. After reloading,
A
If this method still does not solve the problem, replace the chime battery, and set time and chime and music is getting weaker and weaker. If the battery is low, it will leak, and corrode the ADJ button (Figure 2) on the battery box. Each time you press it, an hour will be added, and
TOP UNIT
if the clock counts 2 times at 4 o'clock, please press button two times then it gives corrected
the time will be reported again from 6:00 in the morning.
again by following the "SETTING TIME AND CHIME" procedure.
metal circuit and cause the clock to malfunction. Even damage the battery box. If any of the so on. Note that the TIME ADJ key is after 12 o'clock, and it is 1:00 when you press it again.
strike(picture 2).
5.The hourly timekeeping time is inconsistent with the displayed time. Please set the clock to above problems are found, replace the battery in time.
B
Problem
This restraint is not a substitute for proper adult supervision.
5. TO ADJUST VOLUME CONTROL:
FRONT DOOR
11.If the clock does not report time suddenly, the swing range of the rocker is small or does not 5:55 without placing the battery. After placing the battery, manually or automatically go to
Your clocks chimes are getting quieter and quieter.
This restraint may provide protection against tipping furniture.
desired sound(picture 2).
Solution
swing, the general situation is that the battery power is insufficient, or the connection line 6:00, and the clock will show time as 6:00 AM.
LEFT SIDE
C
Change the chiming section batteries and turn the volume down to about half way.
6.The time is not reported at 10 o'clock during the day, but reported 10 o'clock at night. The between the rocker and the battery box is poor, and you need to reinsert it and confirm
PANEL
Failure to detach this restraint before moving furniture may
STEP 9
whether it is secure. main reason is that the clock defaults to night as day. You can press the TIME ADJ (Figure 2)
Problem
STEP 6
STEP 3
RIGHT SIDE
12.How to tell the time, the volume is normal, the swing range of the pendulum is unstable, or button on the battery box for 12 times to change the time to day or night time.
D
Your clock does not chime at 10 pm.
PANEL
Solution 1. To attach the anti-tip cable tie (No.Z3) securely mount one end t to the top of the
7.When the product leaves the factory, the hour hand is set at 5:55. When disassembling the it shakes, etc. In addition to the battery power attenuation, it is usually caused by the hook
TAKE OFF PAPER LABEL
Your clock has an Automatic night mute with the last strike at 9pm and the first strike at 6am.
case piece with the short screw. (No.Z5)
of the pendulum not hanging to the middle position of the beam of the pendulum rod. In the protective tape on the movement, you must be careful to avoid touching the pointer and
E
BACK PANEL
2. Position the case piece against the wall in the desired location.
middle position (Figure 3), and make sure that the pendulum head and the clock body are each line to prevent the clock hand from shifting and the line loose.
Problem
3. Pull the anti-tip cable tie (No.Z3) taut and mark the position of where you will
8.The solution for the clock not reporting the time on the hour, explain the cause of the parallel. Don't deviate, twist, etc.
Can I change when the night mute starts and stops?
Z
secure the other end on the wall.
Solution
B
13.You need to manually push the pendulum head to the left or right, so that the pendulum accident. (Note: Do not manually turn the minute hand clockwise too fast. Turn lightly; do not
DESCRIPTION
No, this function is not available.
4. Drill a 1/4" hole in the spot you marked from anyone of remaining 3 holes in the
BATTERY HOLDER
turn for less than 15 seconds. Otherwise, at least the above problems will occur.) head does not touch the inner wall of the clock case. The pendulum will automatically swing
1
BOLT 8*40mm
anti-tip cable tie (No.Z3) you desired.
（Ｆｉｇｕｒｅ １）
right and left normally.  Solution 1：Pull out the second cap manually when you hear the time report, then pull
Problem
2 5. Tap in plastic wall plug. (No.Z6)
FIXING BARS
You clock does not chime during the day. out the minute hand in the same way and reinstall it to the 12 o'clock position, and
１
ｐｉｃｔｕｒｅ
6. Fasten anti- tip cable tie (No.Z3) with longer screw
Solution
3
CABLE TIE
then manually rotate the minute hand clockwise to the 12 position to confirm whether
Reset the clock according to the "SETTING TIME AND CHIME" procedure.
(No.Z4) provided.
REVISION 3: 07/12/2022 REVISION 3: 07/12/2022
REVISION 4: 06/09/2023
STEP 4-2
ATTENTION: ANTI TIPPING SAFEGUARD
CAUTION
G
ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE COASTER FINE FURNITURE
TROUBLESHOOTING
A
SIZE D
2 PCS
ｈｏｌｅ
C
ｈｏｏｋ
Turn the minute hand(Longer hand)clock wise tenderly until the desired
H
ASSEMBLY TIME PER UNIT:
PARTS IDENTIFICATION
weight
FIGURE
①
C
Press the "time adj" button for adding the time of striking. For example,
WARNING
pendulum
Injury may result from tipping furniture.
Do not allow children to climb on furmiture.
result in injury and damage.
HARDWARE IDENTIFICATION
②
D
FIGURE
BATTERY HOLDER
（Ｆｉｇｕｒｅ ２）
STEP 7-2
STEP 1-2
ASSEMBLY TOOLS REQUIRED
⑥
X
③
The button in position( ): this selection will only
J
STEP 2-2
I
QTY PART NAME
F
1PC BASE UNIT
H
TOP
G
1PC
To turn button rightward or leftward to obtain the
DECORATION
H
PENDULUM
1PC
DECORATION
I
E
1PC
D
WEIGHTS
DECORATION
J
1PC
CHAINS
C
①
QTY DESCRIPTION
D
4
8PCS LONG SCREW
2PCS 5 Grandfather Clock Grandfather Clock
SHORT SCREW
２
ｐｉｃｔｕｒｅ ｐｉｃｔｕｒｅ
6
1PC PLASTIC ANCHOR
PAGE 10 OF 12 PAGE 11 OF 12 PAGE 12 OF 12 PAGE 6 OF 12 PAGE 2 OF 12 PAGE 3 OF 12 PAGE 4 OF 12 PAGE 5 OF 12 PAGE 7 OF 12 PAGE 8 OF 12 PAGE 9 OF 12
PAGE 1 OF 12 PAGE 1 OF 12
STEP 4-3
A
④
⑤
D
20 MINUTES BY 2 PERSONS
A
FIGURE
①
A
①
E
ｔｕｒｎ ｔｈｅ ｌｏｎｇｅｒ
Fine Furniture for every stage of life Fine Furniture for every stage of life
ｈａｎｄ ｏｎｌｙ
H
FIGURE
900721 900721
４５ ．
（Ｆｉｇｕｒｅ ３）
３
ｐｉｃｔｕｒｅ
COASTERFURNITURE.COM COASTERFURNITURE.COM COASTERFURNITURE.COM COASTERFURNITURE.COM COASTERFURNITURE.COM COASTERFURNITURE.COM COASTERFURNITURE.COM COASTERFURNITURE.COM COASTERFURNITURE.COM COASTERFURNITURE.COM COASTERFURNITURE.COM
COASTERFURNITURE.COM COASTERFURNITURE.COM
A
J
E
QTY
1PC
1PC
1PC
2PCS
X
4PCS
QTY
1PC
1PC
４
1PC