Advertisement
Quick Links
Lighted Power Connection /
Lighted End Termination Kit
Installation Instructions
Terminator ZL-L-WP
for use with RSX, TSX, VSX self-regulating heating cables
Terminator ZL-S-WP
for use with BSX, HTSX, KSX self-regulating, HPT power-limiting,
and FP constant watt heating cables
For Power Connection (1-2 Heating Cables)
or End Termination (1 Heating Cable) Applications
Advertisement
Related Manuals for Thermon Terminator ZL-L-WP
Summary of Contents for Thermon Terminator ZL-L-WP
- Page 1 Lighted Power Connection / Lighted End Termination Kit Installation Instructions Terminator ZL-L-WP for use with RSX, TSX, VSX self-regulating heating cables Terminator ZL-S-WP for use with BSX, HTSX, KSX self-regulating, HPT power-limiting, and FP constant watt heating cables For Power Connection (1-2 Heating Cables)
-
Page 2: Kit Contents
De-energize all power sources before opening enclosure. Installation must comply with Thermon requirements and be Keep ends of heating cable and kit components dry before and installed in accordance with the regulations as per the norm EN during installation. -
Page 3: Installation Instructions
Kit Contents Installation Instructions PETK power termination components (per cable) - order separately PETK-1: for RSX, TSX, VSX PETK-2: for BSX, KSX, HTSX PETK-3: for HPT (up to 200°C) PETK-4: for HPT (up to 260°C) IEK insulation entry kit (per cable) - order separately Slide appropriate IEK insulation entry kit components onto IEK-SXL:... - Page 4 Installation Instructions Mount expediter to bracket using M5 screws and lock Terminate cable with appropriate PETK termination kit. washers. Refer to PETK installation instructions. Locate bus connection (HPT and FP only) as shown. Push excess cable back through expediter. Tighten cap Cut end of cable at angle to aid in piercing grommet.
- Page 5 Installation Instructions Install power cable (if necessary). Use screwdriver to ratchet on junction box lid. Lid will rotate 30 degrees. Install quick mount terminal blocks and tighten screws (if Lid latch mechanism fully engaged. To remove lid, repeat necessary). steps 14 and 15 but in the opposite direction. Complete system wiring.
-
Page 6: Wiring Details
Français Instructions d’installation des kits de connexion avec voyants ZL-S-WP pour utilisation avec les câbles chauffants Thermon de type BSX, HTSX, KSX, HPT et FP ZL-L-WP; pour utilisation avec les câbles chauffants Thermon de type RSX, TSX et VSX Raccordement d’alimentation pour 1 à 2 câbles,ou terminaison d’un câble Les kits de terminaison des câbles et les colliers de serrage ne sont pas inclus dans ces kits... - Page 7 één zijde aan de deksel en de andere zijde aan de bodem van de aansluitkast. 16. Om het deksel te verwijderen, moeten de stappen 14 en 15 in omgekeerde volgorde uitgevoerd Монтаж должен осуществляться в соответствии с требованиями компании Thermon и нормами worden.
- Page 8 Facsimile: +31-(0)15-36 15 379 Website: www.thermon.com Corporate Headquarters Thermon Manufacturing Company 100 Thermon Drive • San Marcos, TX 78666 • U.S.A. Phone: +1-512-396-5801 • Facsimile: +1-512-396-3627 For the Thermon office nearest you visit us at www.thermon.com THERMON...The Heat Tracing Specialists ...
Need help?
Do you have a question about the Terminator ZL-L-WP and is the answer not in the manual?
Questions and answers