Roline 21.13.1074 Quick Installation Manual

ROLINE Gigabit Converter,
RJ45-Mini GBIC
21.13.1074
Quick Installation Guide
Technical Specifications
Standards IEEE 802.3 10BaseT
IEEE 802.3u 100BaseTX
IEEE 802.3ab 1000BaseT
IEEE 802.3z 1000BaseSX/LX
IEEE 802.3x Flow Control
Features Number of Ports:
1x10/100/1000BaseT(X) TP port
2x1000BaseSX/LX SFP open
slots
Data
20/200/2000Mbps/Full-Duplex
Transfer Rate
Transmission TP: 10/100/1000BaseT(X) Cat.
Media 5, 5E, 6 UTP/STP, up to 100m
1000BaseSX:
50/125μm Multi Mode Fiber
optic cable, up to 220m
62.5/125μm Multi Mode Fiber
optic cable, up to 550m
1000BaseLX:
9/125μm Single Mode Fiber
optic cable
Introduction
This Gigabit Ethernet Media Converter is able to
bridge a 10/100/1000BaseT(X) signal to a
1000BaseSX/LX signal. It extends the distance
between two Gigabit Ethernet twisted-pair
devices via a fiber cable transparently with no
performance degradation.
This Media Converter is based on a switching
hub design. It supports Auto-Negotiation and
Flow Control on the twisted-pair port. There are
two SFP slots for multi-mode or single-mode
SFP modules.
Key Features
Compliant with IEEE 802.3 10BaseT,
IEEE 802.3u 100BaseTX, IEEE 802.3ab
1000BaseT and IEEE 802.3z 1000BaseSX/LX
1x 10/100/1000BaseT(X) Ethernet TP Port

and 2x 1000BaseSX/LX Gigabit Ethernet
Fiber Port
2x 1000BaseSX/LX Fiber Port can support

either Multi or Single Mode
TP Port can support Half/Full-Duplex,

Auto-MDI/MDI-X and Auto-Negotiation
19" Converter Chassis for up to 16 slots with
redundant power supply for optional
expansion use.
Application
Two Operating Modes:
RJ-45 to SFP

SFP to SFP

SFP can be SM or MM

Installation
DC Input & External Power Adapter
External Power Adapter specification:
The device DC Input is +5VDC 2A.
The TP Port
The device TP port supports Auto-MDIX,
Auto-Negotiation and Flow Control. It can work
in the 10BaseT, 100BaseTX or 1000SX/LX
environment and the cable length is up to 100
meters for Cat5, Cat5e or Cat6
shielded/unshielded twisted-pair cable.
2 x SFP slots
There are two SFP slots for SFP modules. Both
multi-mode and single-mode are supported.
Package Contents
Before you start to install this coverter, please
verify if your package contains the following
items:
One Media Converter

One Power Adapter

One Quick Installation Guide

Note: If any of these items is missing or damaged,
please contact your local supplier for replacement.
LEDs
LED Indicators of Media Converter
LED Status Operation
Power
On Power is on
(Amber)
Copper 1G 1Gbps/
On/Off
(Green) Under 1Gbps
Copper
Link/Act. On/Flashing Link/Transmitting
(Green)
SFP1
Link/Act. On/Flashing Link/Transmitting
(Green)
SFP2
Link/Act. On/Flashing Link/Transmitting
(Green)
LLF/LFP Function
Link Loss Forwarding (LLF) / Link Fault
Pass Through (LFP) is a function to pass
the message if the optical fiber link fails.
With the optical fiber link fault pass
through, system administrators are able to
notice the link failure within a short period
of time, minimizing the loss caused by this
problem.
Notice: SFP to SFP mode does not
support LFP function, and the DIP switch
must be turned off.