Subscribe to Our Youtube Channel
Summary of Contents for cre8audio ASSEMBLER
- Page 1 ASSEMBLER User guide V 1.0 Assembler is a trademark of Cre8audio LLC. Copyright © 2025 Cre8audio...
- Page 2 Assembler Design Team Product Design and Manual: Richard Nicol Analog Research and Engineering: Michael Johnsen Sound Refinement and Calibration: Perry Willig Prototyping: Ross Johnson Firmware: Luna Sea Peaks Executive Producer: Al Joelson Layout and Design: Jongjian Cai Firmware Support: Zhiwen Huang...
-
Page 3: Table Of Contents
1 | Important Power Information 1.1 : Read Instructions! 1.2 : Eurorack Power Cable Information 2 | User Interface 3 | Assembler Overview 3.1 : Overview 3.2 : Panel Labeling Conventions 3.3 : Manual Labeling Conventions 4 | User Interface_ 4.1 : Complex Channel Strips 1 and 2... - Page 4 Thank You! I would like to take a moment to express my gratitude for your purchase of Assembler. Thank you for inviting Cre8audio and Pittsburgh Modular to be a part of your creative process. I can’t wait to hear what you create.
-
Page 5: Important Power Information
On Cre8audio and Pittsburgh Modular cases the positive and negative voltages are clearly labeled. On the Cre8audio Assembler Mixer module, the power header is clearly labeled and keyed to ensure a safe and proper connection. -
Page 6: User Interface
2 | User Interface Channel 1 Mono Input 29. Channel 2 Aux 1 Level 59. Channel 7/8 Control Button Channel 2 Mono Input 30. Channel 2 High EQ 60. Channel 9/10 Control Button Channel 3 Mono Input 31. Channel 2 Aux 2/3 Level 61. -
Page 7: Assembler Overview
3 | Assembler Overview 3.1 Overview: Designed for hands-on control and instant creativity, the Cre8audio Assembler is a one-knob- per-function mixing powerhouse. Assembler features a set of flexible audio channel strips designed by Pittsburgh Modular to deliver warm, analog sound with an intuitive and direct interface. -
Page 8: Complex Channel Strips 1 And
4.1 Channel 1 and 2 Overview Channel 1 and 2 offer the largest number of sound manipulation tools within Assembler. They contain vintage High/Low EQ. Aux 1 and Aux 2/3 attenuators, panning pot, pre-amp gain boost, mute, and headphone cue send. -
Page 9: Skinny Channel Strips 3 Through
4 | Skinny Channel Strips 3 Through 6 4.2 Channel 3 through 6 Overview Channel 3 through 6 offer a number of sound manipulation tools. They contain Aux 1 and Aux 2/3 attenuators, panning pot, pre-amp gain boost, mute, and headphone cue send. [Channel Level Knob] The Channel Level knob sets the level of the signal sent to {Main L/R Output} and/or {Headphone Output}. -
Page 10: Stereo Channel Strips 7/8 And
4 | Stereo Channel Strips 7/8 & 9/10 4.3 Channel 7/8 and 9/10 Overview Channel pairs 7/8 and 9/10 can be utilized as stereo or mono channels. They contain Aux 1/2/3 attenuator, preamp gain boost, mute, and headphone cue send. [Channel Level Knob] The Channel Level knob sets the level of the signal sent to {Main L/R Output} and/or {Headphone Output}. -
Page 11: Aux Channels
4 | Aux Channels 4.4 Aux Channels Overview Auxiliary Channels are flexible enough to work with eurorack format effects, guitar effects pedals, or as sub mixes. The Aux returns offer up to 2.7x gain to boost lower level signals or to overdrive eurorack signal levels. Auxiliary Channels 1 and 2 have a mono send and mono/stereo return. -
Page 12: Outputs
4 | Outputs 4.4 Main and Headphone Outputs Overview Assembler has both a main output channel and a headphone output channel. The main output channel is designed with a high gain range for use with eurorack systems, and the headphone output is a line level headphone amp. -
Page 13: Factory Reset
5.1 How To Reset All Factory Settings: To perform a Factory Reset, hold the [Aux Send Button],[Gain Boost Button], and [Cue Button] for three seconds. The Assembler startup animation will play, and your Assembler will reset all settings to factory defaults. -
Page 14: Warranty
Cre8audio Product(s) within fourteen (14) days of time of original purchase. To register Cre8audio Products, visit Cre8audio.com. If the unit fails within the one (1) year period, it will be repaired, or replaced, at Cre8audio’s option, at no charge, when returned prepaid to the Cre8audio Technical Service Center with proof of purchase –...
Need help?
Do you have a question about the ASSEMBLER and is the answer not in the manual?
Questions and answers