Table of Contents
Advertisement
Quick Links
Assembly instructions
CTP card reader
For third-party manufacturer vehicle models
Version 02-2025
Source: Manufacturer image databases
Daimler Truck AG, Stuttgart, Germany
Domicile: Stuttgart, Court of Registry: AG Stuttgart, Commercial Register No.: 762884
Chairman of the Supervisory Board: Joe Kaeser
Board of Management: Karin Rådström, Chairman; Karl Deppen, Andreas Gorbach, Jürgen Hartwig, John O'Leary, Achim Puchert, Eva
Scherer
Advertisement
Table of Contents
Summary of Contents for FLEETBOARD CTP
- Page 1 Assembly instructions CTP card reader For third-party manufacturer vehicle models Version 02-2025 Source: Manufacturer image databases Daimler Truck AG, Stuttgart, Germany Domicile: Stuttgart, Court of Registry: AG Stuttgart, Commercial Register No.: 762884 Chairman of the Supervisory Board: Joe Kaeser Board of Management: Karin Rådström, Chairman; Karl Deppen, Andreas Gorbach, Jürgen Hartwig, John O'Leary, Achim Puchert, Eva...
-
Page 2: Table Of Contents
CTP button assignment Work steps Fleetboard cabling Connecting the EX3 wiring harness Connecting YM1 adapter cable to CTP adapter cable Installing GSM/GPS and LTE antennas Connecting CTP to card reader Connecting CTP card reader to the vehicle Installation of CTP vehicle computer... -
Page 3: Safety Note
CTP card reader and with the rules of this guide. In case of doubt, they must contact the vehicle manufacturer. Responsi- bility for correct assembly lies solely with the installing workshop. -
Page 4: Foreword
Fleetboard Work- shop Support before assembly. (For contact details, see section 3.4 / page 12) If a CTP is removed, it must be deactivated on the Fleetboard homep- www.fleetboard.com/activate before removal! -
Page 5: Parts Overview
1.3 PARTS OVERVIEW Device installation mounting Card reader frame A 088208426 A 0014461460 A 0005421587 FleetBoard EX3 wiring YM1 adapter cable CTP adapter cable harness A 0025407505 A 0585454028 A 0035404805 FleetBoard MSDL wiring harness A 0035406505 GSM/GPS adhesive antenna... -
Page 6: Brief Overview
See manufacturer’s Connecting vehicle battery to on-board electrical system instructions MB (WIS AR54.10-W-0003H) Installation and function test of CTP vehicle computer Section 3 / page 11 See manufacturer’s Installing trim parts instructions Fleetboard® Workshop Support Section 3.4 / page 12 1.5 CTP BUTTON ASSIGNMENT... -
Page 7: Work Steps
2 WORK STEPS 2.1 FLEETBOARD WIRING EX3 wiring harness YM1 adapter cable CTP adapter cable MSDL wiring harness A 0035404805 A 0025407505 A 0565454028 A 0035406505 1= Connection 1= Connection 1= Connection = Connection EX3 wiring harness EX3 wiring harness... -
Page 8: Connecting The Ex3 Wiring Harness
2.2 CONNECTING THE EX3 WIRING HARNESS On-board electrical connection, FMS interface (for MB vehicles, see appendix): The open cable strands are connected to the vehicle's FMS interface Pinning: Brown = Terminal 31 (ground connection) Brown/orange = DTCO (D8) Blue = CAN High Yellow = CAN Low Red/purple = Terminal 30 (continuous positive) Black/yellow = Terminal 15 (ignition) -
Page 9: Connecting Ym1 Adapter Cable To Ctp Adapter Cable
2.3 CONNECT YM1 ADAPTER CABLE TO CTP ADAPTER CABLE 1) Open securing bracket on white plug of YM1 wiring harness 2) Connect YM1 wiring harness to white plug (CTP adapter cable). 3) Close the securing bracket again. 4) The blue plug is not required. -
Page 10: Connecting Ctp To Card Reader
A 0014461460 A 0088208426 1) Copy (photograph) ICCID number from CTP. 2) Insert CTP into card reader (clicks into place), the USB cable must not be pinched! 3) Mount/connect the guide pin and USB cable to the card reader according to the enclosed instructions 2.6 CONNECT CTP CARD READER TO... -
Page 11: Installation Of Ctp Vehicle Computer
3.1 TEST INSTRUCTIONS FOR CTP CARD READER Testing procedure: 1. Determine the telephone number using the ICCID via the FleetBoard portal. 2. Enter the ICCID number at https://ticket.fleetboard.com/ICCID_Research and write down the telephone number (+49151xxxxxxxx). 3. Switch on the ignition. -
Page 12: Fleetboard® Commissioning
COMMISSIONING 3.3 FLEETBOARD® Please use the Fleetboard activation links listed below to commission vehicles. Activation links: www.fleetboard.fr/activate, www.fleetboard.es/activate, www.fleetboard.nl/activate, www.fleetboard.pl/activate, www.fleetboard.co.uk/activate, www.fleetboard.cz/activate, www.fleetboard.it/activate, www.fleetboard.ro/activate, www.fleetboard.com/activate 3.4 FLEETBOARD® WORKSHOP SUPPORT Contact information for Fleetboard® Workshop Support Can be reached: Monday to Friday: 9:00 a.m. to 5:00 p.m. -
Page 13: Appendix: Mb Vehicles
APPENDIX: MB VEHICLES Fleetboard retrofitting possible: Mercedes Benz vehicles as of year of manufacture 2011, which do not have Fleetboard/CTP pre-installation, but only have one FMS interface ex works. If no FMS interface is available ex works, this must be retrofitted. -
Page 14: Vehicles With Fms Interface Ex Works
4.2 VEHICLES WITH FMS INTERFACE EX WORKS On-board electrical connection, FMS interface available ex works (MB vehicles) The open cable strands are connected to the vehicle's FMS interface which is usually located at the top near the tachograph behind a cover. FMS interface pinning Brown (terminal 31/ground connection) PIN 1...
Need help?
Do you have a question about the CTP and is the answer not in the manual?
Questions and answers