Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for rovsun CZ260W
Summary of Contents for rovsun CZ260W
- Page 1 DIGITAL CEILING MOUNTED HEATER Model No.: CZ260W...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Safety Information ........................Operating Instructions Assembly Instructions ............Care and Maintenance ........................Limited Warranty Troubleshooting .............. -
Page 3: Intended Use
INTENDED USE Electric Utility heaters are designed to meet a variety of heating requirements. This product is intended for indoor use only. Use only with electrical wiring that is in good working order and that meets applicable codes and ordinances. If you have any questions whether your wiring is adequate, consult a qualified electrician. - Page 4 WARNING: FIRE HAZARD Heater has hot and arcing or sparking parts inside. Do not use near combustible materials or flammable gases or sources of heat. DO NOT USE in areas where gasoline, paint or flammable materials are used or stored. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
-
Page 5: Vertical Air Flow
WARNING: FOR INDOOR USE ONLY, IN A DRY LOCATION FREE OF GASOLINE, PAINT, FLAMMABLE LIQUIDS OR COMBUSTIBLE DUST OR MATERIALS. DO NOT USE EXTENSION CORDS MAXIMUM MOUNTING HEIGHT USING BRACKET FOR: VERTICAL AIR FLOW: The maximum recommended ceiling height for effective vertical air flow is 11 ft. HORIZONTAL/ANGLED AIR FLOW: The maximum recommended ceiling height for effective vertical air flow is 8 ft. -
Page 6: Timer Function
OPERATION AND TEMPERATURE SETTING: 1. This heater is designed to maintain a comfortable room temperature. Always operate the heater in the upright position following all instructions and recommendations listed in this manual. When the heater is turned on by pressing the POWER button, it will heat at power of 10000 W. The LED display panel will show the ambient temperature. -
Page 7: Wifi Function
4. Make sure the heater and phone are on the same WLAN. Open the APP and click "add device" to find "10000W Industrial Heater CZ260W". Click "Add" when you find the device and then enter the Wifi password. After waiting for a while to connect successfully, you can control the heater through your mobile phone. -
Page 8: Bracket Installation
INSTALLING THE HEATER: LOCATING THE HEATER: Install the heater out of traffic areas, maintaining the clearances stated in Figure 1 above. The air flow from the heater must not be restricted or obstructed by any items in the room. When more than one heater is used in an area, the heaters should be arranged so that the air discharge of each heater supports the air flow of the others to provide best circulation of warm air, as indicated below in Figure 3. -
Page 9: Connecting The Power
Use top slots/hole in bracket and small knob-screws if heater is to be tilted down. Install the springs and louvers to the heater and adjust louvers up or down to control air flow. WIFI 8 .8 . Remove screws from the panel to access power Figure 5 block, See Figure 7. - Page 10 CONDUIT CONDUIT CONNECTOR 3ft. If Heater is to min. be turned and wire is inside conduit. FLEXIBLE FLEXIBLE CONDUIT CONDUIT CONNECTOR If Heater is to Figure 6 be connected with NM Cable. FLEXIBLE FLEXIBLE NM CABLE CONNECTOR NM CABLE (use per electircal codes) If Heater is to be connected with Flexible...
-
Page 11: Safety Instructions
SAFETY INSTRUCTIONS: To start the heater, turn on the circuit breaker. The Power Indicator light will light up to indicate there is power available. Press the POWER button to turn the heater on. The heater will be in HIGH setting by default. The heater indicator will illuminate, and the LED display will show the default setting temperature 80°F. -
Page 12: Troubleshooting
ERROR CODE TROUBLESHOOTING GUIDE: Error Code Possible Cause Recommended Solution Clearing Error Codes E1 (Fan Figure 1. To Clear E1 Code: Heater Blade Not 1. Power Off Heater *8 inches minimum from rear of heater Spinning) *13 inches minimum from side of heater Overheat 2.
Need help?
Do you have a question about the CZ260W and is the answer not in the manual?
Questions and answers