Summary of Contents for ELTEX slimBAR
- Page 1 Operating Instructions slimBAR Series R47 Discharging Bars for AC Operation BA-en-2074-2501...
- Page 2 BA-en-2074-2501_R47...
-
Page 3: Table Of Contents
List of contents Outline of appliance ........6 Safety . - Page 4 BA-en-2074-2501_R47...
-
Page 5: Dear Customer
• no health hazards in case of electric shocks when making contact with the tips The optimum discharging effect is guaranteed in conjunction with the Eltex ES47 high voltage power supply. Please read the operating instructions carefully before operating the unit. -
Page 6: Outline Of Appliance
1. Outline of appliance Fig. 1: Overview of the R47 discharging 1 High voltage conductor 2 Ionising tips 3 Sliding nuts M5 (2x) 4 Sliding nuts M5 (only for AL > 1000) BA-en-2074-2501_R47... -
Page 7: Safety
Other uses are not permitted. The discharging bars must be operated only together with the dedicated Eltex PI, ES6x, ES51 or ES24 power supplies. These power supplies guarantee the optimum adaptation to the required operational data for the different active bar lengths. -
Page 8: Work And Operational Safety
2.3 Work and operational safety Warning! Carefully observe the following notes and the complete chapter 2 "Safety”, page • Before carrying out repairs, cleaning or maintenance work and before resetting the unit after malfunctions, switch off the power supply and disconnect the mains supply voltage (see chapter 5 "Maintenance”, page... -
Page 9: Contact Protection
2.4 Contact protection As the site of installation and/or use of the units is outside the control of Eltex, contact protection against inadvertent contact by personnel as spe- cified by the employers’ liability insurance association (e.g. DGUV V3 in Germany) may have to be provided. -
Page 10: Technical Advance
The manufacturer reserves the right to make changes to the technical specifications without prior notice in order to adapt the units to state-of- the-art engineering. Eltex will provide the latest information on any changes or modifications in the operating instructions on request. -
Page 11: Installation And Assembly
3. Installation and assembly 3.1 Assembling the discharging bar The mounting profile of the Series R47 discharging bars is grooved. The sliding nuts pushed into these grooves allow the bar to be bolted and mounted. Fig. 2 shows the bar with the required installation distances. Max. - Page 12 Locating the discharging bar The best possible discharging results are achieved if the bar is located in areas with minimum web capacities. In practical terms this means placing the bar with maximum distances from the machine environment, i.e. no discharging against the idler roller. A rough guideline: A space with the radius R of the bar distance to the web ought to be kept free of any conductive material (Fig.
-
Page 13: Maximum Active Bar Length And Length Of The High Voltage Cable
3.2 Maximum active bar length and length of the high voltage cable Both the lengths of the high voltage cable and of the active bars are limited. The shielded high voltage cables cause a capacitive load on the transformer inside the power supply. The maximum loading capacity is a result of the function of the total active bar length and the total length of all high voltage cables. -
Page 14: Connecting The High Voltage Cable To The Power Supply
3.3 Connecting the high voltage cable to the power supply Warning! Connect or disconnect the high voltage cable only with the power supply switched off. For the connection to the power supplies, refer to the separate operating instructions for the appropriate power supply. BA-en-2074-2501_R47... -
Page 15: Operation
4.2 Function control Use the Eltex Volt Stick or a glow-lamp voltage tester to check the proper function of the emission points. Quote Article No. 109136 when ordering the Volt Stick from Eltex. -
Page 16: Maintenance
5. Maintenance Warning! • Switch off the power supply unit and disconnect the supply voltage before carrying out any maintenance or repair work. • The machine which has the units fitted must not be in operation. • The bars passively absorb energy from the moving substrate web. The high voltage cable must be plugged in or grounded to the power supply. -
Page 17: Troubleshooting
6. Troubleshooting • Warning! Electric shock hazard! • Switch off the power supply unit and disconnect the supply voltage before carrying out any maintenance or repair work. • The machine which has the units fitted must not be in operation. •... -
Page 18: Technical Specifications
1,860 mm see Fig. 6. Weight approx. 0.5 kg/m Operating voltage max. 5 kV AC High voltage supply only via Eltex power supplies as shown on appliance High voltage marking: connection high voltage cable encapsulated, axial lead-out Short-circuit current max 0.5 mA... -
Page 19: Dimensions
8. Dimensions "- O Y Fig. 6: Dimensions of the R47 discharging AL = active length GL = total length *M5 depending on length number of sliding nuts M5: AL of 120 - 1000 mm: 2 pieces AL of 1020 - 1860 mm: 3 pieces max. -
Page 20: Spare Parts And Accessories
9. Spare parts and accessories Article Article No. High voltage distributor discharging , 4 terminals (1 high voltage cable, 4 outputs) specify plug and socket type and cable length ESV61/_ _ High voltage distributor discharging, 2 terminals (1 high voltage cable, 2 outputs) specify plug and socket type and cable length ESVY61/_ _ Extension cable... - Page 21 BA-en-2074-2501_R47...
- Page 24 Eltex offices and agencies The addresses of all Eltex agencies can be found on our website at www.eltex.de Eltex-Elektrostatik-Gesellschaft mbH Blauenstraße 67-69 79576 Weil am Rhein | Germany Phone +49 (0) 7621 7905-422 eMail info@eltex.de Internet www.eltex.de...
Need help?
Do you have a question about the slimBAR and is the answer not in the manual?
Questions and answers