Advertisement
Quick Links
Declaration of conformity
Mirka Ltd, 66850 Jeppo, Finland
declare under our sole responsibility that the Mirka® products (listed below and see "Technical data" table for particular model) to which
this declaration relates are in conformity with the following standards or other normative documents: EN 60745-1:2009/A11:2010, EN
60745-2-23:2013, EN 55014-1:2017/A11:2020, EN 55014-2:2015, EN IEC 63000:2018 in accordance with the regulations 2006/42/EC,
2014/30/EU, 2011/65/EU, 2015/863/EU & 2012/19/EU. The battery charger are in conformity with the following standards and directives;
EN 60335-1:2012/A2:2019, EN 60335-2-29:2004/A11:2018, EN 62233:2008, EN 55014-1:2017, EN 55014-2:2015, EN 61000-3-2:2014, EN
61000-3-3:2013, EN IEC 63000:2018 in accordance with the regulations 2014/35/EU, 2014/30/EU, 2011/65/EU, 2015/863/EU & 2012/19/EU.
®
Products: Mirka
ARG-B 200 Cordless grinder
Jeppo 03.08.2021
Place and date of issue
Company
Original instructions. We reserve the right to make changes to this manual without prior notice.
Important
Read these safety and operating instructions carefully before installing, operating or maintaining this tool. Keep these
instructions in a safe and accessible place. Read and comply with state and local regulations.
Required personal safety equipment
Read
operator's manual
Symbols
Complies with EU relevant standards
Complies with UK relevant regulations
Complies with China Rohs requirement
Complies with Australia & New Zealand RCM requirement
Cordless grinder
Warning: Potential hazardous situation that may result in death or serious injury and/or property damage.
Caution: Potential hazardous situation that may result in minor or moderate injury and/or property damage.
Stefan Sjöberg, CEO
Wear
safety glasses
ear protection
Manufacturer / Supplier
Mirka Ltd
66850 Jeppo, Finland
Tel. +358 20 760 2111
Fax +358 20 760 2290
www.mirka.com
Wear
Wear
safety gloves
en (original)
Wear
face mask
Mirka® ARG-B 200 Cordless grinder
75
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for MIRKA ARG-B 200
Summary of Contents for MIRKA ARG-B 200
- Page 1 Mirka Ltd, 66850 Jeppo, Finland declare under our sole responsibility that the Mirka® products (listed below and see "Technical data" table for particular model) to which this declaration relates are in conformity with the following standards or other normative documents: EN 60745-1:2009/A11:2010, EN 60745-2-23:2013, EN 55014-1:2017/A11:2020, EN 55014-2:2015, EN IEC 63000:2018 in accordance with the regulations 2006/42/EC, 2014/30/EU, 2011/65/EU, 2015/863/EU &...
-
Page 2: General Power Tool Safety Warnings
Power tool use and care Do not overload the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. Mirka® ARG-B 200 Cordless grinder... - Page 3 The arbour size of wheels, sanding drums or any other accessories must properly fit the spindle or collet of the power tool. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control. Mirka® ARG-B 200 Cordless grinder...
-
Page 4: Further Safety Instructions For All Operations
(which is the same direction as the chips are thrown). Feeding the tool in the wrong direction causes the cutting edge of the bit to climb out of the work and pull the tool in the direction of this feed. Mirka® ARG-B 200 Cordless grinder... -
Page 5: Additional Safety Warnings
Read all instructions before using this tool. All operators must be fully trained in the proper, safe use of this tool. All maintenance must be carried out by trained personnel. For service, contact a Mirka authorized service center. If the tool appears to malfunction, stop using it immediately and arrange for service and repair. -
Page 6: Technical Data
Measured values are determined according to EN 60745. Cordless ARG- B 200 Sound pressure level (L 70 dB(A) Sound power level (L 81 dB(A) Sound measurement uncertainty K 3.0 dB(A) Vibration emission value a 11.1 m/s Mirka® ARG-B 200 Cordless grinder... -
Page 7: Battery And Charger
Mirka Ltd accepts no responsibility for the consequences of using declared values instead of actual exposure values for any individual risk assessment. -
Page 8: How To Get Started
When grinding is finished, make sure the tool comes to a complete stop before laying th tool down. Remove the battery from the tool by simultaneously pressing the button on both sides and removing the battery from the tool. Charge the battery. Mirka® ARG-B 200 Cordless grinder... -
Page 9: Maintenance
The Bluetooth word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Mirka Ltd is under license. Other trademarks and trade names are those of their respective owners. Maintenance Always remove the battery before maintenance! -
Page 10: Troubleshooting Guide
Servicing must always be performed by trained personnel. To keep the tool warranty valid and ensure optimal tool safety and function, servicing must be carried out by a Mirka authorized service centre. To locate your local Mirka authorized service centre, contact Mirka Customer Service or your Mirka dealer.
Need help?
Do you have a question about the ARG-B 200 and is the answer not in the manual?
Questions and answers