Page 1
SN75ZX13CE Dishwasher EN Information for Use Register your appliance on My Siemens and discover exclusive services and offers. Siemens Home Appliances...
en Table of contents You can find additional information and explanations online. Scan the QR code on the title page. Table of contents Table of contents 1 Safety .......... 3 8.5 Cutlery drawer ...... 2 1 1.1 General information...
en Safety ¡ in closed rooms in the home and with similar applications, e.g.: in canteens in shops, offices and other work environments; in agricultural businesses; use by customers in hotels, motels and other typical home environments; in bed and breakfasts. ¡...
Page 5
Safety en isolating switch must be integrated into the permanent electrical installation according to the installation regulations. When installing the appliance, check that the power cable is not trapped or damaged. Cutting through the supply hose or immersing the Aqua-Stop valve in water is dangerous. Never immerse the plastic housing in water.
en Safety 1.5 Safe use WARNING ‒ Risk of serious harm to health! Failure to comply with safety instructions and directions for use on packagings of detergent and rinse aid products may cause seri- ous harm to health. Follow the safety instructions and directions for use on the packagings of detergent and rinse aid products.
Safety en Never expose the appliance to intense heat or humidity. Do not use steam- or high-pressure cleaners to clean the appli- ance. If the insulation of the power cord is damaged, this is dangerous. Never let the power cord come into contact with hot appliance parts or heat sources.
en Safety 1.7 Risk to children WARNING ‒ Risk of suffocation! Children may put packaging material over their heads or wrap themselves up in it and suffocate. Keep packaging material away from children. Do not let children play with packaging material. Children may breathe in or swallow small parts, causing them to suffocate.
Preventing material damage en Modified or damaged water hoses 2 Preventing material may result in material damage and Preventing material damage damage damage to the appliance. Never kink, crush, modify or cut 2.1 Safe installation through water hoses. Only use the water hoses supplied ATTENTION with the appliance or genuine Improper installation of the appliance...
en Environmental protection and saving energy So as not to scratch the finish on During dishwashing, heat energy is the appliance, do not use sponges used to heat up the washing water with a rough surface or abrasive and dry the mineral. cleaning agents.
Installation and connection en Note: The appliance has been tested Connect the appliance to the at the factory to check it is in working power supply. order. It is possible that water has left 4.3 Drainage connection marks on the appliance. These marks will disappear after the first Connect your appliance to drainage wash cycle.
en Installation and connection 4.5 Electrical connection Insert the non-heating appliance plug of the power cable into the Connecting the appliance to the appliance. electricity supply Insert the mains plug of the appli- Notes ance's power cable in a socket Follow the Safety instructions nearby.
Familiarising yourself with your appliance en 5 Familiarising yourself with your appliance Familiarising yourself with your appliance 5.1 Appliance You can find an overview of the parts of your appliance here. Rating plate with E number and FD number Page 47 . Rating plate The data you need for Customer Service Page 47 .
en Familiarising yourself with your appliance Add the special salt to the dispenser for Dispenser for special salt special salt. "Water softening system", Page 22 The lower spray arm washes the tableware in the bottom basket. Lower spray arm If the tableware has not been washed prop- erly, clean the spray arms.
Page 15
Familiarising yourself with your appliance en With some buttons you can perform different functions. 3 4 5 6 Page 30 Switching on the appliance Page 31 ON/OFF button and reset Switching off the appliance button Terminating the programme Page 31 Programme buttons Programmes Page 16 ...
en Programmes Door handle 1 Open the appliance door. The display shows information about the remaining running time or the basic settings. You can change the basic set- Display tings via the display and the setting buttons. "Changing basic settings", Page 34 1 Symbols on the display Symbol...
Page 17
Programmes en energy consumption will increase if the rinse aid system is switched off or if rinse aid needs to be added. The consumption values can be found in the quick reference guide. The con- sumption values relate to normal conditions and a water hardness of 16 - 20 °E.
en Additional functions Note: The relatively long running time The pre-rinse program is saved to in the Eco 50 ° programme is due to this button at the factory. Pre-rinse is longer soaking and drying times. This suitable for all types of tableware. results in optimal consumption val- The tableware undergoes intermedi- ues.
Features en Symbol Additional func- tion IntensiveZone Switch on with mixed loads containing table- ware with different soiling levels, e.g. place very soiled pots and pans in the bottom bas- ket and normally soiled tableware in the top basket. The spray pressure in the bottom basket is increased and the maximum programme temperature maintained longer.
en Features Adjusting top basket with side or for large items of cutlery, e.g. cooking spoons or serving cutlery. levers To wash large items of tableware in the baskets, adjust the shelf position of the top basket. Pull out the top basket. To prevent the basket from sud- denly dropping down, hold the side of the basket by the top edge.
Features en 8.4 Folding prongs Push the lever forwards and fold down the prongs Use the folding prongs to position tableware securely, e.g. plates. To use the prongs again, fold them back up. The prongs audibly click into posi- You can fold the prongs down to po- tion.
en Before using for the first time Start the Programme with the 9 Before using for the highest cleaning temperature Before using for the first time first time Page 31 without tableware. To remove any marks from water 9.1 Performing the initial con- or other residues, we recommend figuration you operate the appliance without...
Water softening system en Note: Set the water hardness determ- ness, the greater the consumption of ined on your appliance. special salt. "Setting the water softening sys- ATTENTION tem", Page 23 Detergent may damage the water With a water hardness of 0 - 8 °E softening system.
en Rinse aid system 10.4 Switching off the water 10.5 Regeneration of the water softening system softening system If you find the special salt refill indic- In order to obtain fault-free function of ator irritating, e.g. when using com- the water softening system, the appli- bined detergents with salt replace- ance performs regeneration of the ment substances, you can switch the...
Rinse aid system en Only use rinse aid for domestic dish- Press . washers. To open the basic settings, press for 3 seconds. Adding rinse aid The display shows Hxx. If the rinse aid refill indicator lights The display shows up, top up with rinse aid. Only use Press repeatedly until the rinse aid for domestic dishwashers.
en Detergent To save the settings, press Powder detergent for 3 seconds. Powder detergent is recommended The rinse aid system is switched for shorter programmes. off and the rinse aid refill indicator The dosage can be adjusted to the is deactivated. level of soiling.
Detergent en as glass protection or stainless steel According to the manufacturers, cleaner. combined detergents with salt re- According to the manufacturers, placement substances can only be combined detergents generally only used up to a certain water hard- function up to a water hardness of ness, usually 26 °E, without 26 °E.
en Tableware for dosage in the detergent dis- liquid detergent will spread around penser. the washing tank and dissolve 20 ml – 25 ml detergent is suffi- there. Tablets will fall into the tab- cient for normal soiling. If table- let collecting tray and dissolve in ware is only lightly soiled, slightly the right dosage.
Tableware en Cause Recommendation safe to use in the dishwasher with alu- ing agents, do not put aluminium parts minium. in the dishwasher interior. The water temperature of the pro- Select a programme with lower temper- gramme is too high. atures. After the programme has ended, take glassware and cutlery out of the appli- ance without delay.
en Basic operation To prevent injury, arrange cut- – 14 Basic operation lery with the points and sharp Basic operation edges facing down. 14.1 Switching on the appli- Position containers with the – ance openings facing down so no wa- Press . ter can collect in them. The Eco 50°...
Basic settings en Press the button for the relevant 14.6 Interrupting programme additional function. Note: When you open the appliance "Additional functions", Page 18 door once the appliance has heated The additional function is set and up, leave the door slightly ajar for a the additional function button few minutes and then close it.
en Basic settings 15.1 Overview of the basic settings The basic settings depend on the features of your appliance. Basic setting Display text Selection Description 1 Water hardness H00 - H07 Set the water softening sys- tem to your water hardness. "Setting the water softening system", Page 23 Level H00 switches the water softening system off.
Basic settings en Basic setting Display text Selection Description ended when the strip of light is no longer visible on the left-hand side. Switch SideLight on "I01" or off "I00". 1 Tone volume b00 - b03 Adjustment of tone volume. Level "b00" switches the sig- nal tone off.
en Home Connect Basic setting Display text Selection Description Confirm with The settings for initial start-up must be configured. 15.2 Changing basic settings The Home Connect app guides you through the entire login process. Fol- Tip: Connect your appliance to a mo- low the instructions in the Home Con- bile device.
Home Connect en the function is permanently activated Press and you can start your appliance with Smart Start is active. a mobile device at any time. The programme starts as soon as the optimal time is reached. Activating Remote Start Tip: Deactivate the function a single When you have selected "rc1"...
Tip: You can get our tested and approved Dishwasher Care and Machine Cleaner for Dishwashers online at https://www.siemens-home.bsh-group.com/ store or from customer service. Machine Care is a programme which removes various deposits in one washing cycle.
Cleaning and servicing en To ensure optimum cleaning perform- Place the machine care product in ance, the programme doses the de- the appliance interior. tergents independently of each an- Only use machine care products other during the relevant cleaning specially designed for dishwash- phase.
en Cleaning and servicing Turn the coarse filter anticlockwise Re-assemble the filter system. and remove the filter system Make sure that the locking catches Check that no foreign objects on the coarse filter click into posi- fall into the sump. tion. Insert the filter system into the ap- pliance and turn the coarse filter clockwise.
This will avoid unneces- sary costs. Tip: You can find further information and explanations on troubleshooting on- line by scanning the QR code on the title page and on our website siemens- home.bsh-group.com. WARNING Risk of electric shock! Improper repairs are dangerous.
Page 40
en Troubleshooting Fault Cause and troubleshooting Display "Check water A technical fault is present. supply" flashes Press . Unplug the appliance or switch off the fuse. Wait at least 2 minutes. Insert the mains plug of the appliance in a socket or switch on the fuse.
Page 41
Troubleshooting en Fault Cause and troubleshooting E:32-00 will light up The filters in the water connection of the supply or alternately or indicator AquaStop hose are blocked. for water supply lights Switch off the appliance. Pull out the mains plug. Turn off the water tap. Unscrew the water connection.
Page 42
en Troubleshooting Fault Cause and troubleshooting E:61-03 will light up alternately. Water is not drained. Not an appliance fault. Wastewater pump is blocked or the cover of the wastewater pump is loose. Clean the wastewater pump. "Clean wastewater pump", Page 45 Secure the cover of the wastewater pump so it clicks into position.
Page 43
Troubleshooting en Fault Cause and troubleshooting All LEDs lit up or Electronics have detected a fault. flashing. Press the main switch button for approx. 4 seconds. "Controls", Page 14 The appliance is reset and restarted. If the problem occurs again: Switch off the appliance. Pull out the mains plug or switch off the fuse in the fuse box.
Page 44
en Troubleshooting Fault Cause and troubleshooting Remnants of food on Filters are inserted incorrectly and/or not engaged. tableware. Insert the filters properly. "Filter system", Page 37 Engage the filters. Washing programme selected too weak. Select a more intensive washing programme. "Programmes", Page 16 Tableware has been precleaned too intensely.
Troubleshooting en Fault Cause and troubleshooting Rust spots on cutlery. Cutlery is not sufficiently rust-resistant. Knife blades are often more severely affected. Use rust-resistant tableware. Cutlery may also rust if washed together with rusting items. Do not wash rusting items. Salt content in washing water is too high. Remove any spilled special salt from the tub.
en Transportation, storage and disposal Insert the pump cover and press 19.3 Transporting the appli- down ance To avoid damage to the appliance, empty it before transporting. Note: Always transport the appliance upright to prevent residual water get- ting into the machine's controls and damaging the appliance.
Customer Service en Unplug the appliance from the Nr.), the production number (FD) and mains. the consecutive numbering (Z-Nr.) of Cut through the power cord. your appliance. Dispose of the appliance in an en- You can find the contact details for vironmentally friendly manner.
en Technical specifications to our instructions; this also in- If your appliance is fitted with cludes correctly fitting the Aqua- Aqua-Stop, you can in principle Stop extension (genuine access- leave your appliance unattended ory). Our guarantee does not cover during operation and the tap defective supply lines or fittings up turned on afterwards.
BSH Hausgeräte GmbH hereby declares that the appliance with Home Connect functionality conforms to the essential requirements and other relevant provi- sions of Directive 2014/53/EU. A detailed RED Declaration of Conformity can be found online at siemens- home.bsh-group.com among the additional documents on the product page for your appliance.
Page 50
en Declaration of Conformity group is seen on the title page. The The manufacturer, BSH Hausgeräte full model identifier is made up of the GmbH deems that it has complied characters before the slash in the with product number (E no.) which can be provision 5.1-1 of ETSI EN 303 found on the rating plate.
Page 52
EN Manufactured by BSH Hausgeräte GmbH under the trademark licence of Siemens AG Valid within Great Britain: Imported to Great Britain by BSH Home Appliances Ltd. Grand Union House Old Wolverton Road Wolverton, Milton Keynes MK12 5PT United Kingdom BSH Hausgeräte GmbH Carl-Wery-Straße 34...
Need help?
Do you have a question about the SN75ZX13CE and is the answer not in the manual?
Questions and answers