Subscribe to Our Youtube Channel
Related Manuals for Dreamland HUNKER DOWN SCANDI SHERPA
Summary of Contents for Dreamland HUNKER DOWN SCANDI SHERPA
- Page 1 H U N K E R D O W N S C A N D I S H E R P A M A T T R E S S W A R M E R TYPE R9007 R9023 R9018 R9013 R9021 Instructions for use...
-
Page 2: Description Of The Appliance
ILLUSTRATIVE GUIDE Temperature table Fast Pre-heat 5-4 Medium Pre-heat 3-1 Continuous or all night use DESCRIPTION TECHNICAL DATA OF THE APPLIANCE 1. Underblanket connector 2. Control connector 3. Mains socket TYPE R90* 220-240 V 50/60 Hz 150 W 4. Rating Label TYPE R90* 220-240 V 50/60 Hz 2x150 W 5. - Page 3 Dear Customer, thank you for choosing our product. We feel certain you will appreciate its quality and reliability as it was designed and manufactured with customer satisfaction in mind. These instructions for use are compliant with the European Standard EN 82079. INDEX page 1 Illustrative guide...
- Page 4 IMPORTANT INSTRUCTIONS. RETAIN FOR FUTURE USE. WARNING! Instructions and warnings for safe use. Before using this appliance, carefully read the instructions for use and in particular the safety notes and warnings, which must be complied with. Keep this manual together with its illustrative guide for future consultation.
- Page 5 Children under the age of three are not to use this appliance due to their inability to react to overheating. • This appliance can be used by children older than 3 years and younger than 8 years under supervision and with the control always set to minimum temperature.
- Page 6 • When storing the appliance, allow it to cool down before folding. WARNING! DO NOT crease the appliance by placing items on top of it during storage. WARNING! For use, cleaning, maintenance and storage of the appliance, please follow the instructions specified in the corresponding chapters.
- Page 7 the other side. • Run the control unit cable along the floor next to the bed. Do not squash the control unit cable between the mattress and the bed frame. • Insert the plug of the control unit cable in the mains socket (3). Every time the plug is inserted, the control unit automatically performs a self-diagnosis, lighting up all LEDs (10, 11) in a clockwise sequence for around two seconds.
-
Page 8: Cleaning And Maintenance
AUTO SHUT OFF TIMER The underblanket has an automatic shut off timer of 1, 3 or 9 hours. When switched on, the control unit automatically sets itself to 1 hour on the auto shut off timer and LED 1h lights up in green (10). To set a different auto shut off timer, press the timer selector button (6) and select the desired timer. - Page 9 the drying cycle it must be air-dried to allow it to dry completely. • Remove the underblanket from the tumble dryer at the end of the drying cycle and reshape it to its original size. • Allow the underblanket to fully air-dry before using it again. DRYING IN THE OPEN AIR •...
-
Page 10: Troubleshooting
TROUBLESHOOTING This chapter describes the most common problems that can arise using the appliance. If the problems cannot be solved with the information below, please contact the Authorised Service Centre. Problem Solution Check that the control unit plug is fully inserted in the The LEDs on the control unit socket (3). - Page 11 The user must therefore take the appliance to an appropriate recycling centre for electrical and electronic equipment. Alternatively, instead of handling the disposal, the user can hand over the appliance to the retailer when a new, equivalent one is purchased. The user can hand over electronic products measuring less than 25 cm to retailers of electronic products having a sales area of at least 400 m free of charge and with no obligation to buy.
- Page 12 Corporate address for GB IMETEC UK ltd c/o XEINADIN MANCHESTER 100 Barbirolli Square, Manchester, M2 3BD, UK. www.dreamlanduk.co.uk Address for Ireland/NI Tenacta Group S.p.A. Via Piemonte 5 IT-24052 Azzano S. P. EN You can always download the most updated version of the manual from the website indicated...
Need help?
Do you have a question about the HUNKER DOWN SCANDI SHERPA and is the answer not in the manual?
Questions and answers