Table of Contents
Advertisement
Quick Links
Hydraulic Earth Auger Attachments
Models: HO20PD, HO25PD, HO30PD, HO35PD
Operator's Manual
Serial Number: ______________________________
Model Number: ______________________________
WARNING!
To avoid Injury or death read and understand this entire manual
before installing, operating, or servicing this equipment.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Premier HO20PD
Summary of Contents for Premier HO20PD
- Page 1 Hydraulic Earth Auger Attachments Models: HO20PD, HO25PD, HO30PD, HO35PD Operator’s Manual Serial Number: ______________________________ Model Number: ______________________________ WARNING! To avoid Injury or death read and understand this entire manual before installing, operating, or servicing this equipment.
-
Page 3: Table Of Contents
TABLE OF CONTENTS To The Owner ........................1 Warranty Registration Form ....................2 Warranty Policy ........................4 Safety Information ....................... 5 Skid Steer Loader Installation Instructions ................7 Backhoe & Excavator Installation Instructions ............... 9 Hydraulic Hookup Instructions ................... 11 Operating Instructions ........................... -
Page 4: To The Owner
Premier Hydraulic Earth Auger Attachment. Please be sure all operators study this manual carefully and keep it on file for future reference. After reading this manual if you have any questions about your Premier Hydraulic Earth Auger Attachment, please contact us as follows:... - Page 5 Installation & Application Information This Premier Hydraulic Earth Auger will be mounted on: _________________________________ This Premier Hydraulic Earth Auger Attachment has been accepted in good condition and I have been instructed by the dealer and/or read and understand the entire Operator’s Manual for proper installation, proper and safe operation, preventative maintenance and service, warranty, and all other information covered in the Operator’s Manual.
- Page 6 THIS PAGE WAS PURPOSELY LEFT BLANK...
-
Page 7: Warranty Policy
PREMIER HYDRAULIC AUGER WARRANTY POLICY Model #: _______________________________ Serial #: ____________________________________ Premier warrants its products to be free from defects in material or workmanship for a warranty period as stated below. Earth Auger Drive Units: 60 Months Auger Bits & Mountings: 12 Months The warranty period begins on the date of purchase by the original purchaser. -
Page 8: Safety Information
PROTECTED AGAINST MECHANICAL MEANS OR PRODUCT DESIGN. ALL OPERATORS OF THIS EQUIPMENT MUST READ AND UNDERSTAND THIS ENTIRE MANUAL, PAYING PARTICULAR ATTENTION TO SAFETY AND OPERATING INSTRUCTIONS, PRIOR TO USING THE PREMIER HYDRAULIC EARTH AUGER ATTACHMENT IF YOU ENCOUNTER ANYTHING IN THIS MANUAL... - Page 9 SAFETY INFORMATION Never check a pressurized system for leaks with your bare hand. Oil escaping from pinhole leaks under pressure can penetrate skin and could cause serious infection. Hold a piece of cardboard next to suspected leaks and wear a face shield or safety eye protection. If any fluid is injected into the skin, it must be removed immediately by a doctor.
-
Page 10: Skid Steer Loader Installation Instructions
Skid Steer Loader Installation Instructions Reference # Part # Description Quantity 95000 Mount Weldment 91002 Swivel 91001 Knuckle Pin 40009 Snap Ring 40010 Hex: ¾” – 10 HHCS ½” Long 40016 Round: 7/8” HHCS 4-1/2" Long 40011 ¾” Hex Nut 40017 Round: 7/8"... - Page 11 Duo-Tach® Installation Instructions Reference # Part # Description Quantity 95040 Mount Weldment 91002 Swivel 91001 Knuckle Pin 40009 Snap Ring 40010 Hex: ¾” – 10 HHCS ½” Long 40016 Round: 7/8” HHCS 4-1/2" Long 40011 Hex: ¾” Hex Nut 40017 Round: 7/8"...
-
Page 12: Backhoe & Excavator Installation Instructions
READ AND UNDERSTAND ALL SAFETY INFORMATION BEFORE ATTEMPTING INSTALLATION 1. Remove bucket from dipper arm and curl cylinder pin connections. The dipper arm pin will be used to attach backhoe/excavator mounting to backhoe dipper arm. Curl cylinder pin will not be required for Premier Earth Auger Attachment. - Page 13 Backhoe & Excavator Pin on Mount Installation Instruction Reference # Part # Description Quantity Varies Backhoe/ Excavator Mounting Bracket 91002 Swivel 91001 Knuckle Pin 40009 Snap Ring ½” Hex Flange Nut 40005 ½” -13 HHCS 2” Long 40006 91003 Cradle 40010 Hex: ¾”...
- Page 14 Drive Unit Exploded View & Part Numbers Reference # Part # Description Quantity 91046 HO20, HO25, HO30 Drive Unit Housing 91091 HO35 Drive Unit Housing 60042 HO20 Motor 60041 HO25 Motor 60033 HO30 Motor 60034 HO35 Motor 40004 ½” -13 SHCS 1- 1/2 Long 61001 Planetary Gasket 65050...
- Page 15 4. Models HO20PD, HO25PD, HO30PD, and HO35PD require two ½” I.D. hoses with #10 JIC female fittings on one end of each to connect hoses to Drive Unit fittings.
-
Page 16: Operating Instructions
Operating Instructions 1. After installation instructions have been completed, safety information read and understood, and the remainder of this operator’s manual has been reviewed, your Premier Attachments Earth Auger is ready for use. 2. With the auger raised off the ground and the vehicle engine set at a low RPM, activate the earth drill control valve to determine position. -
Page 17: Maintenance Instructions
API-GL-5 number 80 or 90 for filling planetary gear reduction under normal temperature rangers between 0˚F and 120˚F. Approximate oil capacity for models HO20PD, HO25PD, HO30PD, and HO35PD is 1.5 pints. Check oil level daily to assure proper lubrication is maintained. - Page 18 How to Check Oil...
-
Page 19: Troubleshooting
Oil Leaks Fittings loose or damaged Tighten or replace Hydraulic motor seals See dealer for repair worn or damaged For further assistance, please contact your dealer or contact Premier Attachments Customer Service Department as follows: Toll Free: 866-458-0008 Local: 260-456-8518 E-Mail:... -
Page 20: Drive Unit Specifications
Output speed and torque specifications are based on theoretical values and are provided for comparative purposes only. Premier Attachments Is continually striving to improve its products. Therefor we reserve the right to make changes to our products or specifications at any time without notice or obligation. -
Page 21: Planetary Exploded View & Parts List
Planetary Exploded View & Parts List Reference # Part # Description Quantity 69200 2” Hex Output Shaft 69201 2-9/16” Round Output Shaft 69018 Heavy Duty Oil Seal 69203 Outer Bearing Cone 69204 Bearing Cup 69205 Magnetic Plug 69206 Hub Casting 69218 Inner Bearing Cone 69207... -
Page 22: Planetary Service Procedures
Planetary Service Procedures Assembly General Instructions 1. Press new bearing cups into each side of hub. It is recommended that the bearing To facilitate the repair of these units and cups and cones be replaced in sets. before any work is completed, we suggest 2. -
Page 23: Motor Exploded View
Motor Exploded View 69217 Bolt NOTE Unless otherwise indicated, measurements are given in inches [mm] throughout the Hydraulic Motor Service Procedures. Tools Required for Disassembly & Reassembly ▲ Torque Wrench 500 lb. in. capacity ▲ 12-16 Breaker Bar ▲ 9/16” Socket ▲... -
Page 24: Motor Service Procedures
Motor Service Procedures Disassembly 1. Remove the 4 Tie Bolts from the motor (Fig. Cleanliness is extremely important when repairing a hydraulic motor. Work in a clean area. Before disconnecting the lines, clean the port area of the motor thoroughly. Use a wire brush to remove foreign material and debris from and around the exterior joints of the motor. - Page 25 Motor Service Procedures Continued… 15. Remove the Diameter Seal from Bearing Housing (Fig. 5. Remove two Pins and two springs from balance Ring Assembly (Fig. 5) 16. You may need a press to remove the Shaft and Bearing 6. Remove Balance Ring Assembly (Fig. 5). 7.
- Page 26 Motor Service Procedures 21. Place tape over shaft to prevent cutting the seals. Apply petroleum jelly to the inside Continued… diameter of Dust and Shaft Seal. You may Reassembly need a press to install Shaft and Bearing Check all mating surfaces. Replace any parts Assembly.
- Page 27 Motor Service Procedures 32. Install two Springs and two Pins in the hole located in the Bore Housing (Fig. 14). Continued… 33. Apply a light film of petroleum jelly to the Diameter Timing Step 1: Locate the largest open pocket in Seal.
- Page 28 Motor Service Procedures Continued… 36. Install the Tie Bolts and finger tighten. Torque al four Tie Bolts alternated to 450 lb-in [50nm] 37. Install Seal on Case Drain Plug then install in Valve Housing.
- Page 29 Accessories & Auger Replacement Parts Construction Auger Teeth Figure 1 Part # Description 00200 Wisdom Tooth 00201 Chisel Tooth 00202 Wisdom Gage Tooth 00205 Hardfaced Wisdom Tooth Hardfaced Chisel Tooth 00206 00207 Hardfaced Wisdom Gage Tooth 00208 Carbide Wisdom Tooth 00209 Carbide Chisel Tooth 00237...
Need help?
Do you have a question about the HO20PD and is the answer not in the manual?
Questions and answers