1. Manuals
  2. Brands
  3. Outcast Manuals
  4. Boat
  5. PAC 1150
  6. Owner's manual

Outcast PAC 1150 Owner's Manual

Hide thumbs

Advertisement

Table of Contents

PAC 1150 OWNER'S MANUAL
ALWAYS WEAR A COAST GUARD APPROVED FLOTATION
DEVICE WHEN OPERATING THE PAC 1150.
Know the limits of your abilities and the limits of your equipment.
Changes in air temperature and elevation may cause the air inside the
PAC 1150 to expand which could cause a tube to burst. Always release
some air when these conditions occur.
Never leave your boat sitting in direct sunlight when it is out of the water.
This owner's manual will help you with initial set-up of your new
PAC 1150, provide basic maintenance tips, and covers simple
field repair.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PAC 1150 and is the answer not in the manual?

Questions and answers

Related Manuals for Outcast PAC 1150

Summary of Contents for Outcast PAC 1150

  • Page 1 Know the limits of your abilities and the limits of your equipment. Changes in air temperature and elevation may cause the air inside the PAC 1150 to expand which could cause a tube to burst. Always release some air when these conditions occur.
  • Page 2 BEFORE YOU BEGIN, Check for damaged or missing parts. 1 - PAC 1150 raft collar 1 - PAC 1150 raft floor 1 - Seat back 1 - Dry Box 1 - Seat bottoms with swivel FRONT REAR 2 - Side Rails...
  • Page 3 1 - Vinyl tube valve adapter Changes in air temperature and elevation could cause the air inside the PAC 1150 to expand which could cause damage to the AIREcells. Never leave your fully inflated tube sitting in direct sun light out of the water. Always release some air when...
  • Page 4 3. The bow of the raft collar has a built-in splash guard. The valve in the floor should be at the stern of the raft. 1 - PAC 1150 raft collar 4. Place the floor in the cam strap cradle. Be sure the drain holes in the floor are facing up toward the bottom of the raft.
  • Page 5 Step 2 Continued: Raft Floor Installation Diagram After the floor is laced in you can inflate the raft to full pressure. Full pressure is reached when you can depress about 1/4” from the top surface of the tube. If you hear a humming sound in the floor valve, it’s the pressure release valve indicating the floor has reached maximum pressure (2.5 psi) and you can stop pumping.

  • Page 6: Step 3: Main Frame Assembly

    Step 3: Main Frame Assembly TEE MOUNTS — USE SET PIN SCREWS CASTING DECK 2 - Side Rails 1 - Cross Bar with anchor bracket 1 - Cross Bar with Kick Bar Front/Bow Rear/Stern FRONT REAR 2 - End Hoops 1.
  • Page 7 Step 4: Casting Deck — Frame Assembly Items needed: Tee Mounting Bracket End Hoop Bar Set Pin Screws go here Metal Attachment Bar Springer Clips 1 - Casting Deck w/ Strap and Plastic Guard Insert Hole on Casting Deck 2- Metal Attachment Bars 4 - Springer Clips (squared) 4 - Set Pin Screws 1.

  • Page 8: Step 6-1: Seat Assembly

    Step 6: Flip Bracket Seat Base & Seat — Frame Assembly Items needed: COPED & WELDED FLIP BRACKET ANCHOR SYSTEM MAIN ROWING FRAME STRIPPING LEAN BAR BASKET CASTING DECK 1 - Flip Bracket Seat Base 2 - Springer Clips (squared) 1.
  • Page 9 Step 7: Rower Seat — Frame Assembly Items needed: 1 - Dry Box 2 - Cam Straps 1. Place Dry Box in the gap between the Rear End Hoop and the Rear Crossbar with anchor mount. Move crossbar to snugly fit the Dry Box in this slot, so the dry box slides in and the metal tabs rest on top of the crossbar and end hoop.
  • Page 10 2. Tighten all the Tee Mount Set Pin Screws on the main frame. 3. Strap each corner of the frame to side D-rings of the PAC 1150 with 4, 3’ cam straps. 4. Use the remaining 2, 3’ cam straps to attach the Lean Bar to the corner D-rings on each side of the raft.

  • Page 11: Storage Tips

    Storage Tips • It is best to store your PAC 1150 to soft pressure under a cover or car port that provides protection from environmental elements. This will help prevent weather and UV damage and will keep your AIREcells aligned.
  • Page 12 • Leafield valve wrench - Used to tighten or loosen the inflation valve and pressure release valve of your boat. • Repair needle and thread - Used to stitch tears in the PVC outer shell of the PAC 1150 • 5/32” hex key - Used to tighten or loosen the bolts on the handles or zipper bridge.

  • Page 13: Warranty

    Extensive Repairs If you have a major rip or tear in your boat that is beyond your abilities to repair, please contact Outcast at 844-556-5730 for a Return Authorization (RA) number. Please put a brief note with your contact information and a detailed description of the repairs necessary inside the box and ship the package to the address below with the RA number clearly written on the outside of the box.

Table of Contents