Parts list ………………………………………………………………………………………………….…..… 5 Part order ordering instructions …………………………………………………………………………..6 Floor Layout……………………. …………………………………………………………………………..7 Installation / Start-up………………………………………………………………………………………. 8-11 Maintenance…………………………………………………………………………………………………… 12 Troubleshooting….…………………………………………………………………………………………… 13 All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
(contract, tort or otherwise) upon which the claim is based, and notwithstanding the failure of any agreed or other remedy of its essential purpose. Rev 17-0314 All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
LIABILITIES. ALL WARRANTIES AND LIABILITIES SHALL ALSO BE VOID IF PARTS MANUFACTURED BY MAYFRAN INTERNATIONAL ARE REPLACED WITH PARTS OBTAINED FROM A SOURCE OTHER THAN MAYFRAN INTERNATIONAL. All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
PUMP SPECIFICATIONS Motor HP Voltage Amps 208-230V 5.0A (6.8 Max) 3450 460V 2.5A (3.4 Max) 3450 All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
Shortage: If any parts are missing, other than parts marked back ordered, call the factory immediately. P.O. BOX 43038 6650 BETA DRIVE CLEVELAND, OHIO 44143 PHONE: (440) 461-4100 FAX: (440) 461-5565 All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
Mayfran International, Incorporated Installation / Startup / Maintenance Manual FLOOR LAYOUT All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
(Loosely install worm drive clamps on hose prior to sliding hose on barbed nipple for ease of installation.) All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
Page 9
AT-Cleaner on ATMS unit. (Loosely install worm drive clamps on hose prior to sliding hose on barbed nipple for ease of installation.) All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
Page 10
/ pipe assembly. 7) Install hose and piping assemblies on tank using mounting plates and provided M6 bolts and nuts. All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
ATMS to allow coolant to drain from sludge/chips back into the tank. 7) To stop the ATMS, press the red “STOP” button and turn the disconnect switch to the “OFF” position. All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
* In order for the AT-Cleaner to operate efficiently, the inlet pressure must be kept between 14 to 18 PSI. A valve and pressure gauge are supplied to regulate the flow into the AT-Cleaner. All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
Prime pump and hose. proper operating range. REVISIONS Rev. 1: Added row to “PUMP SPECIFICATIONS” showing 460V specs. – CFitzgibbon (10/9/24) All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
Page 14
Installation / Startup / Maintenance Manual P.O. BOX 43038 6650 BETA DRIVE CLEVELAND, OHIO 44143 PHONE: (440) 461-4100 FAX: (440) 461-5565 All drawings shown are typical examples of Mayfran equipment provided for customer education only and are subject to change.
Need help?
Do you have a question about the TSUBAKI ATMS and is the answer not in the manual?
Questions and answers